Discussion
Anyone here on PH do car Smart Repair for a living. I'm thinking about getting into the business and am getting some equipment together before I do a training course, now I have done some research in Air Compressor & Spray Guns but I have not found any real would information on what the Pro use. At the moment I was looking into Air Compressors and Spray guns, I know it's important to get the correct Air compressor looking for FAD information and compering that information to the working CFM of the spray guns. At the moment I am looking at this kind of set-up for Air Compressor, and Air Gun I would appreciate any tips advise please.
Direct Drive, Air Compressor
50Lt, 2Hp, 7.0Cfm, 8Bar/116Psi.
Air Gun
Devilbiss SRI PRO TS1 Gravity Spot Repair Spray gun
Air cap - HS1: 135l /min [4.8 cfm] @ 2.0 bar [30 psi]
Air consumption - TS1: 100l /min [3.5 cfm] @ 2.0 bar [30 psi]
Direct Drive, Air Compressor
50Lt, 2Hp, 7.0Cfm, 8Bar/116Psi.
Air Gun
Devilbiss SRI PRO TS1 Gravity Spot Repair Spray gun
Air cap - HS1: 135l /min [4.8 cfm] @ 2.0 bar [30 psi]
Air consumption - TS1: 100l /min [3.5 cfm] @ 2.0 bar [30 psi]
Edited by BBS-LM on Tuesday 1st September 17:01
Edited by BBS-LM on Tuesday 1st September 17:01
I'd hold off on getting equipment until *after* you've had some training. The more you know about what you're going to be doing, with what materials etc, the less likely you are to buy something that ends up useless.
Whoever does your training will be able to advise on an equipment setup that provides enough air for the tools you're going to be using, and ensures the guns you select are appropriate for the materials you've been trained to use.
Almost any compressor with an air tank will be able to drive a SMART repair spraygun spraying a genuinely-sized SMART repair. The one you've mentioned will be fine. But if you also decide you want an air-powered palm sander, or your training is with isocyanate materials so you also need to provide for air-fed RPE, then you need something with more grunt.
Come and join in at http://www.smartrepairforum.com and you can get loads of input from people who do this for a living....
HTH
Tol
Whoever does your training will be able to advise on an equipment setup that provides enough air for the tools you're going to be using, and ensures the guns you select are appropriate for the materials you've been trained to use.
Almost any compressor with an air tank will be able to drive a SMART repair spraygun spraying a genuinely-sized SMART repair. The one you've mentioned will be fine. But if you also decide you want an air-powered palm sander, or your training is with isocyanate materials so you also need to provide for air-fed RPE, then you need something with more grunt.
Come and join in at http://www.smartrepairforum.com and you can get loads of input from people who do this for a living....
HTH
Tol
Anatol said:
I'd hold off on getting equipment until *after* you've had some training. The more you know about what you're going to be doing, with what materials etc, the less likely you are to buy something that ends up useless.
Whoever does your training will be able to advise on an equipment setup that provides enough air for the tools you're going to be using, and ensures the guns you select are appropriate for the materials you've been trained to use.
Almost any compressor with an air tank will be able to drive a SMART repair spraygun spraying a genuinely-sized SMART repair. The one you've mentioned will be fine. But if you also decide you want an air-powered palm sander, or your training is with isocyanate materials so you also need to provide for air-fed RPE, then you need something with more grunt.
Come and join in at http://www.smartrepairforum.com and you can get loads of input from people who do this for a living....
HTH
Tol
Hi AnatolWhoever does your training will be able to advise on an equipment setup that provides enough air for the tools you're going to be using, and ensures the guns you select are appropriate for the materials you've been trained to use.
Almost any compressor with an air tank will be able to drive a SMART repair spraygun spraying a genuinely-sized SMART repair. The one you've mentioned will be fine. But if you also decide you want an air-powered palm sander, or your training is with isocyanate materials so you also need to provide for air-fed RPE, then you need something with more grunt.
Come and join in at http://www.smartrepairforum.com and you can get loads of input from people who do this for a living....
HTH
Tol
So your a Chipsaway Guy, I looked into doing the ChipsAway Franchise but thought it was to mush money for what was on offer, but that just me, you seem to be doing very well for yourself. I am going to be starting my own business so at the moment I am getting the finance together for the training and equipment and then see where I go from there.
Yes, we went the franchised route, and it's been so successful that we've kept adding franchise territories - we're at five now. Having access to the dominant brand is worth so much IMHO, but each to their own. 
Do take some advice before splurging on kit. For a start, you're going to need more than one spraygun, with paints being waterborne, and clears solvent-borne. Oh, and you might want a gun for primer. And maybe one for blending thinners. And... and...
Tol

Do take some advice before splurging on kit. For a start, you're going to need more than one spraygun, with paints being waterborne, and clears solvent-borne. Oh, and you might want a gun for primer. And maybe one for blending thinners. And... and...

Tol
Gassing Station | Business | Top of Page | What's New | My Stuff


