Track Day Sumps Available

[mgbond]

I had an email from the guy sorting the stone guards out so here it is.

As for the track pans, price is $975 USD, it includes everything you see
in the pictures. I actually have 10 available, if you can find enough
interest to get all 10, I can drop the price by $50, and have everything
sea freighted (it will cost a lot less to send them this way).

We also have a track axle available for the front, to replace the large
bolt and nut. These are $600 for the pair, and will require axle nuts
like the rear.

Serban Gavrilescu
Rossion Automotive
920 SW 2nd Place
Pompano Beach, FL 33069
www.rossioncars.com
TEL: [phone]
FAX: [phone]















Bondy

[daddysumo]

$600 for the front upgraded axle bolts ? Sounds excessive, I'm sure mine from Mr Cundy were nowhere near that amount !

Steve

[Pinnacle]

Remember gents, the prices Serban / Rossion quoted are in USD, so do the math for the GBP which will be less by some margin. Further as regards the front axles that Paul C. offers, these are via Troy at Freedom Autosport in Florida, USofA whom originally developed them after extensive testing. I have some of the original pairs, and this is a NO BRAINER, even if you don't track in my opinion for safety's sake. Don't think so ? go look at the stock units vrs the redesigned spindles and you'll change immediately. As for what Rossion offers as regards the spindles ? Not sure, but I think they have "borrowed" the design which Freedom developed, but's that's between them to sort out. As for the track pans, I believe these are steel material, with earlier units the factory in SA put out being aluminum just as a FYI.

[TrackPredator]

Hey Serban,

So are you able to get the stone chip guards?

Edited by TrackPredator on Tuesday 6th October 05:54

[andygtt]

Dont forget the import duties you will pay when it comes into the UK (around 20% including handling fees)... still cheaper and by the looks of it good quality.

Is the kit fully inclusive of everything you need to fit it?

[MadMacMcMad]

Do we not need to do chassis mods to get it in or is this and easy exchange?

[gaz 7404]

AFAIK its either engine out or cut a chassis member out to get it in. And the floor pan needs trimming to suit the contour of the bigger sump. Gaz

[Adrian W]

MadMacMcMad said:

Do we not need to do chassis mods to get it in or is this and easy exchange?

You will need to either raise the engine or cut the chassis to fit it.

[gaz 7404]

Yeah engine raised not out doh!

[Urbalizer]

Noble motorsports in the UK fitted a baffled sump to my old GTO3 for £550, so i think it is cheaper to source one from the UK.

[mgbond]

TrackPredator said:

Hey Serban,

So are you able to get the stone chip guards?

Edited by TrackPredator on Tuesday 6th October 05:54

I'm not Serban, that was a copy of the email he sent. I'm tolf the SG's and DT's should be posted this week. (was told that last week ).

Bondy

[Metalman]

I'm tolf the SG's and DT's should be posted this week.
[/quote]

[Serban]

Greetings Noble owners, I figured I would join and answer any questions you guys might have regarding the parts we sell.

First off, thank you Martin for posting the pictures of the track day sump we offer. This is indeed a steel sump. The kit you see is almost complete, the only other item not pictured is the gasket. It is also included in the kit. The price of everything is $975 USD, however, I do have a total of ten sumps, if you guys were to do assemble a group buy, price would drop to $925 USD. This is actually a really good price, individually, if you were to build this kit up, it would be right around $1145 USD.

As for the stone guards and drip trays that everyone has been waiting so patiently for, I'm told they should be complete this week. Please understand that these come from the factory in South Africa, and there was a problem with the initial batch, and rather than sending defective units, they're redoing them. I do apologize for the delay, but it is beyond my control.

Best Regards,

Serban

[Gadgeroonie]

Hi Serban,

do you know if the rossion front clam will fit an m12 ?

do you know anything about the new car Lee is building ?

regards

[TrackPredator]

Sorry for the mistake bondy! I read to fast!

[wessexrfc]

Serban said:

Greetings Noble owners, I figured I would join and answer any questions you guys might have regarding the parts we sell.

First off, thank you Martin for posting the pictures of the track day sump we offer. This is indeed a steel sump. The kit you see is almost complete, the only other item not pictured is the gasket. It is also included in the kit. The price of everything is $975 USD, however, I do have a total of ten sumps, if you guys were to do assemble a group buy, price would drop to $925 USD. This is actually a really good price, individually, if you were to build this kit up, it would be right around $1145 USD.

As for the stone guards and drip trays that everyone has been waiting so patiently for, I'm told they should be complete this week. Please understand that these come from the factory in South Africa, and there was a problem with the initial batch, and rather than sending defective units, they're redoing them. I do apologize for the delay, but it is beyond my control.

Best Regards,

Serban

Serban, great to hear from you. This is what makes this site so fantastic I look forward to receiving my SG and DT soon!!!

Paul

[Serban]

Gadgeroonie said:

Hi Serban,

do you know if the rossion front clam will fit an m12 ?

do you know anything about the new car Lee is building ?

regards

The Rossion clam will not fit on a Noble. It does look very similar, but there are quite a few interferences.

And I do not have any knowledge of Lee's new car.

[Gadgeroonie]

do you think a rossion clam could be made that will fit the noble, i love the look of it ?

[Serban]

Gadgeroonie said:

do you think a rossion clam could be made that will fit the noble, i love the look of it ?

As far as I know, the mounting points are different, front 1/4 panels are different, and the supports with the 1/4 turn fastners on the body are different.