Spark plugs won't budge
Author
Discussion

Gad-Westy

Original Poster:

16,666 posts

244 months

Tuesday 16th March 2010
quotequote all
Two of the spark plugs in my mx5 appear to have been overtightened. It also seems that I'm not the first to try and remove them as the heads are a little rounded. Anyway of getting them out without taking the head off? Have tried a few different sockets and tried doing it whilst engine is hot. Just can't grip the little buggers. Starting to think about purchasing another head to have s play with then swap over.

Edited by Gad-Westy on Tuesday 16th March 17:32

_Batty_

12,268 posts

281 months

Tuesday 16th March 2010
quotequote all
Gad-Westy said:
Two of the spark plugs in my mx5 appear to have been overtightened. It also seems that I'm not the first to try and remove them as the heads are a little rounded. Anyway of getting them out without taking the head off. Have tried a few different sockets and tried doing it whilst engine is hot. Just can't grip the little buggers. Starting to think about purchasing another head to have s play with then swap over.
have you used 6 sided sockets?

Extralien

3 posts

200 months

Tuesday 16th March 2010
quotequote all
Same with any tight nut ...be it rusted or heat seized..

TIGHTEN it first to crack the seal.. dont need to go mad, just a nip up..
Then undo... That should sort it..


Uhura_Fighter

7,018 posts

214 months

Tuesday 16th March 2010
quotequote all
Have you given the area a good spray with some penetrant and a few taps with a hammer, more penetrant, wait then try and unscrew?

Gad-Westy

Original Poster:

16,666 posts

244 months

Tuesday 16th March 2010
quotequote all
Thanks chaps. Just to re-iterate, the heads are rounded so gripping them to tighten them etc isn't an option. I have tried both hex type sockets and toothed sockets. Haven't tried the penetrant oil approach yet though have tried tapping them with a hammer. Biggest problem is, that I just can't grip them, the sockets just turn on the heads.

bimsb6

8,812 posts

252 months

Tuesday 16th March 2010
quotequote all
wall drive sockets are your friend .you may have to smash the porcelain first though as i haven't seen them deep enough for a plug .


http://www.ri-tools.co.uk/metrinch.html

mat205125

17,790 posts

244 months

Tuesday 16th March 2010
quotequote all
Uhura_Fighter said:
Have you given the area a good spray with some penetrant and a few taps with a hammer, more penetrant, wait then try and unscrew?
yes

Drown them in WD40, and also try to get a 6 sided socket that holds the faces all the way along the sides of the hex rather than just on the points.

Gad-Westy

Original Poster:

16,666 posts

244 months

Tuesday 16th March 2010
quotequote all
mat205125 said:
Uhura_Fighter said:
Have you given the area a good spray with some penetrant and a few taps with a hammer, more penetrant, wait then try and unscrew?
yes

Drown them in WD40, and also try to get a 6 sided socket that holds the faces all the way along the sides of the hex rather than just on the points.
Have tried numerous sockets of both types (see above), can't get any purchase to exert any torque on them at all.


Gad-Westy

Original Poster:

16,666 posts

244 months

Tuesday 16th March 2010
quotequote all
bimsb6 said:
wall drive sockets are your friend .you may have to smash the porcelain first though as i haven't seen them deep enough for a plug .


http://www.ri-tools.co.uk/metrinch.html
Ahhh, now here's a dilemma. As it stands, I have a working car that could do with a service which is a nuisance. If I smash the porcelain part, I could end up with a freshly service car with a new set of plugs or..... an immobile car with only two spark plugs. Last resort I think.

Starfighter

5,352 posts

209 months

Tuesday 16th March 2010
quotequote all
bimsb6 said:
wall drive sockets are your friend .you may have to smash the porcelain first though as i haven't seen them deep enough for a plug .


http://www.ri-tools.co.uk/metrinch.html
But make sure that you get the shards out with a vacuum cleaner before you remove what is left of the plug. You really don't want bits of very hard ceramics flowing through the combuistion chamber, manifold or cat. Worst of all would be a turbo, very bad news....