Pushrod engines - any still made?
Pushrod engines - any still made?
Author
Discussion

matchmaker

Original Poster:

9,091 posts

231 months

Thursday 25th March 2010
quotequote all
Are there any new cars out there that still use pushrods, rather than OHC?

I'm discounting the likes of Hindustans............

jcelee

1,082 posts

275 months

Thursday 25th March 2010
quotequote all
Suspect the old Ford Ka (with a Kent Crossflow derivative) was last of the mainstream but don't some Chrysler V8s (Hemis etc) and Chevolet V8s still use pushrods?

OnTheOverrun

3,965 posts

208 months

Rothgo Wooft

157 posts

200 months

Thursday 25th March 2010
quotequote all
Rover V8s are still in production in small numbers.

mackie1

8,169 posts

264 months

Thursday 25th March 2010
quotequote all
Yup, GM V8s like the LS series and their less performance-oriented siblings are all pushrod operated. Some have variable timing though like the L99 in the Camaro auto.

The Wookie

14,209 posts

259 months

Thursday 25th March 2010
quotequote all
As mentioned, quite often yank V8's are.

It's good for centre of gravity, overall weight and packaging, just not valvetrain friction and high engine speeds.

Just one engineering solution amongst many, like most bits of a car.

Chris71

21,549 posts

273 months

Thursday 25th March 2010
quotequote all
...at a slightly different end of the scale, wasn't the original Ford Ka (in production until a year or two back I believe) a pushrod engine? I know it owed a lot to the old crossflow, which was.

The Wookie

14,209 posts

259 months

Thursday 25th March 2010
quotequote all
Chris71 said:
...at a slightly different end of the scale, wasn't the original Ford Ka (in production until a year or two back I believe) a pushrod engine? I know it owed a lot to the old crossflow, which was.
That engine in the Ford Ka was so old the engineering drawings were recently rediscovered by an archeological dig, painted on the inside of a cave near Dagenham

750turbo

6,164 posts

255 months

Thursday 25th March 2010
quotequote all
The Wookie said:
Chris71 said:
...at a slightly different end of the scale, wasn't the original Ford Ka (in production until a year or two back I believe) a pushrod engine? I know it owed a lot to the old crossflow, which was.
That engine in the Ford Ka was so old the engineering drawings were recently rediscovered by an archeological dig, painted on the inside of a cave near Dagenham
And purchased by the Chinese to develop for the new Rover Chow Mein?

(sorry, been a long fekkin day)

LuS1fer

43,566 posts

276 months

Thursday 25th March 2010
quotequote all
Both the current American Chevy V8s and the Chrysler V8s are pushrod. Ford went ohc years ago.

Puddenchucker

5,999 posts

249 months

Thursday 25th March 2010
quotequote all
The 6.75 V8 in the bigger Bentleys still has pushrods.

Deluded

4,968 posts

222 months

Thursday 25th March 2010
quotequote all
Did the Skoda fabia not have a pushrod engine? The base spec 1.4 I believe.

Boosted LS1

21,200 posts

291 months

Thursday 25th March 2010
quotequote all
The Wookie said:
As mentioned, quite often yank V8's are.

It's good for centre of gravity, overall weight and packaging, just not valvetrain friction and high engine speeds.

.
Although some of them redline at 7k and have been known to happily go higher.

Cipher

73 posts

205 months

Thursday 25th March 2010
quotequote all
Im pretty sure some big modern-ish diesels are pushrod engines, the old 200 and 300tdi landrover engines are pushrod, the old isuzu 2.8/3.0/3.1td engines are also pushrod and from what ive been hearing they are still getting manufactured today.

dont know what else really but im guessing theres some companys that still use this technology in countrys that are a bit less well off than britain and america.

Robert060379

15,754 posts

214 months

Friday 26th March 2010
quotequote all
Doesn't the fastest car in the world use a push rod engine?

Otto

738 posts

247 months

Friday 26th March 2010
quotequote all
I love pushrods!! LS2 V8 - 6 litres, 400hp, 6600rpm redline - giggity. bounce

Marquis_Rex

7,377 posts

270 months

Friday 26th March 2010
quotequote all
matchmaker said:
I'm discounting the likes of Hindustans............
Hindustan Ambasador uses an OHC fuel injected 1817 cc engine- so why pick that?

Marquis_Rex

7,377 posts

270 months

Friday 26th March 2010
quotequote all
The Wookie said:
As mentioned, quite often yank V8's are.

It's good for centre of gravity, overall weight and packaging, just not valvetrain friction and high engine speeds.
Although the inertia loads are high on a pushrod engine- it's not a forgone conclusion that a pushrod V8 with 16 valves will automatically have higher friction than a more contemporary OHC unit.
There are les bearings for one thing, and the regime of lubrication for the cam in block is also more favourable.
I have data showing the motoring friction comparing the Ford 5.4 vs the Chevy 5.7 that shows the Chevy has MUCH lower friction.
I can well believe that in a well optimised specialist aplication, like the LS7, with Titanium valve train parts and carefully matched roller elements the valvetrain friction of the engine would be alot lower than a comparable contemporary OHC 32 valve engine- such as the Northstar, say, even at high engine speeds.

And then when you compare it with BMWs joke- valvetronic system with all that intentionally added valvetrain inertia for a bit of pumping loss benefit- (which the LS7 series engines already enjoy being 2 valvers with late intake valve closing).

Edited by Marquis_Rex on Friday 26th March 03:10

eliot

11,999 posts

285 months

Friday 26th March 2010
quotequote all
638bhp of pushrod goodness:

jbi

12,700 posts

235 months

Friday 26th March 2010
quotequote all
he's talking about the SSC Aero which holds the current record for fastest production car (beating the veyron)

It uses a supercharged GM V8