Change of Diff.................
Discussion
As a performance upgrade on my CV8 I'm thinking about the diff change.
Just wondering if the diff out of an early VXR would be a good 'half-way-house' between the 3.9.1 option ?
I'm sure this would be a dam bit cheaper than the other option if I got one out of a broken VXR.
At TR I managed 150 constantly but my 1/4 times were poo. What would the lower diff do to my terminal speed if anything ? Not too fussed about 1/4 mile times.
Just wondering if the diff out of an early VXR would be a good 'half-way-house' between the 3.9.1 option ?
I'm sure this would be a dam bit cheaper than the other option if I got one out of a broken VXR.
At TR I managed 150 constantly but my 1/4 times were poo. What would the lower diff do to my terminal speed if anything ? Not too fussed about 1/4 mile times.
SimonV8ster said:
As a performance upgrade on my CV8 I'm thinking about the diff change.
Just wondering if the diff out of an early VXR would be a good 'half-way-house' between the 3.9.1 option ?
I'm sure this would be a dam bit cheaper than the other option if I got one out of a broken VXR.
At TR I managed 150 constantly but my 1/4 times were poo. What would the lower diff do to my terminal speed if anything ? Not too fussed about 1/4 mile times.
Just wondering if the diff out of an early VXR would be a good 'half-way-house' between the 3.9.1 option ?
I'm sure this would be a dam bit cheaper than the other option if I got one out of a broken VXR.
At TR I managed 150 constantly but my 1/4 times were poo. What would the lower diff do to my terminal speed if anything ? Not too fussed about 1/4 mile times.
Just changing from the 3.46 to a 3.7 is a lot of trouble to go to for just 7% extra acceleration. Obviously with a 3.9:1 you get 13% for the same work and cost. I still argue changing the box is better from the TUET2100 (CV8 type) to the TUET2066 (6.0VXR type). Now a few 6.0VXRs have met their end gearboxes should start to appear 2nd hand. Changing the box doesn't effect the speedo so is a DIY proposition.
I changed just the crown wheel and pinion on the Ford 9 in axle in my 72 Mustang. This was fairly straight forward and only cost £200.
SimonV8ster said:
I'm sure this would be a dam bit cheaper than the other option if I got one out of a broken VXR.
As if by magic............
http://cgi.ebay.co.uk/Vauxhall-Holden
I paid approx £2200 all in for a new one, importing it myself from "Regal Performance" in Texas. Pound was better 3 years ago though. So look on eBay including the USA and OZ sites. Another option is www.gmpartsdirect.com, gm part number is 92155485. What ever it says on it or it's history do check at least first is the correct ratio, 2.97:1 which is nearly 3:1, e.g. input goes round 3 times for the output once.
Overall improvement is similar to a 3.9:1 diff though the spread is different. 2nd is the most different 16% shorter, 3rd the least at 10%.
If you are having a box rebuilt then maybe you can just have the gear cluster changed.
Overall improvement is similar to a 3.9:1 diff though the spread is different. 2nd is the most different 16% shorter, 3rd the least at 10%.
If you are having a box rebuilt then maybe you can just have the gear cluster changed.
I think the design of the gearbox means 4th is inherently the same 1:1. Both 5th and 6th are shorter. In my view 5th on the old box is actually better as it sits more evenly between 4th and 6th and is better judged for achieving maximum speed without over revving the engine. This is a relatively minor negative though.
A thread on here last year was claiming Vauxhall were selling off the gearboxes cheap, even £700 might have been mentioned but I don't think anyone reported buying one. A bit difficult to believe but probably still worth a phone call.
Researching the TR6060 or the vin code M10 (VXR8)version of the T56 worth while to.
A thread on here last year was claiming Vauxhall were selling off the gearboxes cheap, even £700 might have been mentioned but I don't think anyone reported buying one. A bit difficult to believe but probably still worth a phone call.
Researching the TR6060 or the vin code M10 (VXR8)version of the T56 worth while to.
granada203028 said:
In my view 5th on the old box is actually better as it sits more evenly between 4th and 6th and is better judged for achieving maximum speed without over revving the engine.
With 174 MPH available in 5th on the limiter I think the M12 5th gear is a better bet over a short distance (TR) for a higher top speed. I believe Harry only managed 160's on the Autobahns when his car was stock with all the room in the world. Its still too tall for the power on stock/low powerd modded cars.
All IMO of course....but I have spent a really really long time researching this and developing mine.
Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



