VXR8 Bonnet vents
Author
Discussion

EssexVXR8

Original Poster:

1,790 posts

218 months

Wednesday 7th April 2010
quotequote all
Im looking at reducing my temps under the bonnet, looked at Aston V12 vantage vents but HOW MUCH yikes now considering Focus RS as the angles are right for bonnet lines, fitted above the headers. What do you think!!!!!!!!

the_ferret82

25,627 posts

215 months

Wednesday 7th April 2010
quotequote all
what are your temps under the bonnet? the only other one i know that has done this is haryOZ...

monkfish1

12,516 posts

255 months

Wednesday 7th April 2010
quotequote all
EssexVXR8 said:
Im looking at reducing my temps under the bonnet, looked at Aston V12 vantage vents but HOW MUCH yikes now considering Focus RS as the angles are right for bonnet lines, fitted above the headers. What do you think!!!!!!!!


How high are your temps. Which ones, IAT or coolant?

gsd2000

11,515 posts

214 months

Wednesday 7th April 2010
quotequote all
S800vxr has some vents in his monaro, dont think it cost him much

SimonV8ster

13,035 posts

259 months

Wednesday 7th April 2010
quotequote all
gsd2000 said:
S800vxr has some vents in his monaro, dont think it cost him much
Yeah, got them cut in, looks the best way to do it IMO.

EssexVXR8

Original Poster:

1,790 posts

218 months

Wednesday 7th April 2010
quotequote all
Only had one real big issue with underbonnet temps, stuck in crawling traffic for 2.5 hours, killed HT leads and couldnt be good for everything else under the bonnet. Headers going to Zircotec for plasma sprayed ceramic coating, thought id do a belt and braces job. Also got a stone dent on bonnet line near where id put vents, so smart man could then access that.

ARAF

20,759 posts

254 months

Wednesday 7th April 2010
quotequote all
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.

ringram

14,702 posts

279 months

Wednesday 7th April 2010
quotequote all
The joys of supercharging never end smile

EssexVXR8

Original Poster:

1,790 posts

218 months

Wednesday 7th April 2010
quotequote all
Doubt the supercharger had anything to do with it crawling in traffic, the rest of the time IAT's are really low its just radiant heat from a large capacity engine in a confined space!

Edited by EssexVXR8 on Wednesday 7th April 11:40

S800VXR

5,877 posts

231 months

Wednesday 7th April 2010
quotequote all
Removing the underbonnet insulation and stamping in vents transformed my concerns with heat, fans hardly ever come on now! (or didnt when I used to have a car!) As for "the joys of SC", IL remind you of that at the next drag day or Thunder Road. smile

How is yr broken NA engine BTW! tongue out

Vez

239 posts

289 months

Wednesday 7th April 2010
quotequote all
ARAF said:
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.
Whats your logic behind that then? This is a high pressure area on the car therefore only let more air into the bay and not let any out. Waste of time and looks shiiiite.

stigmundfreud

22,454 posts

241 months

Wednesday 7th April 2010
quotequote all
S800VXR said:

How is yr broken NA engine BTW!

closer to road use than yow's

S800VXR

5,877 posts

231 months

Wednesday 7th April 2010
quotequote all
stigmundfreud said:
S800VXR said:
How is yr broken NA engine BTW! tongue out
closer to road use than yow's tongue out
Really.... should since its gonna have alot less power! tongue out

ARAF

20,759 posts

254 months

Wednesday 7th April 2010
quotequote all
Vez said:
ARAF said:
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.
Whats your logic behind that then? This is a high pressure area on the car therefore only let more air into the bay and not let any out. Waste of time and looks shiiiite.
I don't think I mentioned winning any beauty contest prizes. If the problem is heat build-up in the engine area when the car is stationary, then raising the trailing edge of the bonnet will allow hot air to escape, before you go to the expense of cutting holes in the bonnet.

S800VXR

5,877 posts

231 months

Wednesday 7th April 2010
quotequote all
ARAF said:
Vez said:
ARAF said:
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.
Whats your logic behind that then? This is a high pressure area on the car therefore only let more air into the bay and not let any out. Waste of time and looks shiiiite.
I don't think I mentioned winning any beauty contest prizes. If the problem is heat build-up in the engine area when the car is stationary, then raising the trailing edge of the bonnet will allow hot air to escape, before you go to the expense of cutting holes in the bonnet.
Its a bit Chavvy though, bloody Corsa boys will be wanting to play with you then.

Vez

239 posts

289 months

Wednesday 7th April 2010
quotequote all
ARAF said:
Vez said:
ARAF said:
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.
Whats your logic behind that then? This is a high pressure area on the car therefore only let more air into the bay and not let any out. Waste of time and looks shiiiite.
I don't think I mentioned winning any beauty contest prizes. If the problem is heat build-up in the engine area when the car is stationary, then raising the trailing edge of the bonnet will allow hot air to escape, before you go to the expense of cutting holes in the bonnet.
It will hinder getting rid of heat when on the move though.

monkfish1

12,516 posts

255 months

Wednesday 7th April 2010
quotequote all
Vez said:
ARAF said:
Vez said:
ARAF said:
Before actually getting the bonnet vented, I'd be inclined to raise the bonnet at the scuttle by an inch or so (as a temporary measure), just to see if that cools things.


Whats your logic behind that then? This is a high pressure area on the car therefore only let more air into the bay and not let any out. Waste of time and looks shiiiite.


I don't think I mentioned winning any beauty contest prizes. If the problem is heat build-up in the engine area when the car is stationary, then raising the trailing edge of the bonnet will allow hot air to escape, before you go to the expense of cutting holes in the bonnet.


It will hinder getting rid of heat when on the move though.


It will reduce airflow over the rad on the move at speed too.

donk r8

2,755 posts

227 months

Thursday 8th April 2010
quotequote all

I am going to have this done, bonnet louvres. There is a company just up the road from me called cool louvres (they did rogers) but at the present time they are trying to find another workshop, so hopefully in a couple of months they will be up and running again.........

rickf_uk

420 posts

219 months

Thursday 8th April 2010
quotequote all
Has anyone here looked at wrapping their header pipes old muscle car style. I was speaking to a local tuner and he quite often does this Ultimas and Nobles to keep engine heat down when racing. He reckons on about £350 for the job on a 'Ro.

ARAF

20,759 posts

254 months

Thursday 8th April 2010
quotequote all
rickf_uk said:
Has anyone here looked at wrapping their header pipes old muscle car style. I was speaking to a local tuner and he quite often does this Ultimas and Nobles to keep engine heat down when racing. He reckons on about £350 for the job on a 'Ro.
You can now get the headers ceramic dipped, for the same insulating effect. There is a downside, but I can't for the life of me remember what it is, at the moment. redface