Heavy rumble at speed?
Heavy rumble at speed?
Author
Discussion

mfp4073

Original Poster:

2,111 posts

205 months

Thursday 22nd April 2010
quotequote all
The otherday I noticed what sounded like a heavy rumble at speed this only happend at around 90 MPH then stopped if my speed dropped down even increased a little. The steering was rock steady and I have just fitted two new rear tyres which were balanced. Is it possible the prop shaft may need to be balanced? or do all Monaros do this?

Regards John

MyM8V8

9,468 posts

226 months

Thursday 22nd April 2010
quotequote all
mfp4073 said:
The otherday I noticed what sounded like a heavy rumble at speed this only happend at around 90 MPH then stopped if my speed dropped down even increased a little. The steering was rock steady and I have just fitted two new rear tyres which were balanced. Is it possible the prop shaft may need to be balanced? or do all Monaros do this?

Regards John
Check your rear wheelnuts for starters.

monkfish1

12,516 posts

255 months

Thursday 22nd April 2010
quotequote all
mfp4073 said:
The otherday I noticed what sounded like a heavy rumble at speed this only happend at around 90 MPH then stopped if my speed dropped down even increased a little. The steering was rock steady and I have just fitted two new rear tyres which were balanced. Is it possible the prop shaft may need to be balanced? or do all Monaros do this?

Regards John


No car should do that!

It could be wheels or the prop. As you have just changed the tyres, it sounds like a starting point.

scarebus

858 posts

202 months

Thursday 22nd April 2010
quotequote all
Mr Monkfish..... can propshafts be balanced? I still have vibrations on my r8, I have balanced all wheels but it still rumbles above 45mph, and seems to be coming from rear end... Ta

monkfish1

12,516 posts

255 months

Thursday 22nd April 2010
quotequote all
scarebus said:
Mr Monkfish..... can propshafts be balanced? I still have vibrations on my r8, I have balanced all wheels but it still rumbles above 45mph, and seems to be coming from rear end... Ta


Yes, but it wont be the balance.

If its not wheels, which it probably is despite the balance (see our web page on this subject!) then it could be prop related, either the drive donuts or, more expensively the spigot mose bush in the gearbox tailshaft.

Maybe a wheel bearing?

I could advise which with a test drive.

scarebus

858 posts

202 months

Thursday 22nd April 2010
quotequote all
Thanks will give you a call when back from hols....

MyM8V8

9,468 posts

226 months

Friday 23rd April 2010
quotequote all
Rog is right about the balance. Even if you've had it done, it will be down to the skill of the fitter (or not) and the quality/calibration of the equipment.

Most high volume tyre shops knock their kit around something terrible and they won't be bothered about a fine balance either.

merge

239 posts

241 months

Friday 23rd April 2010
quotequote all
MyM8V8 said:

Most high volume tyre shops knock their kit around something terrible and they won't be bothered about a fine balance either.


In fairness most main stream tyre shops are dealing with "normal" sized wheels from yonder years ( where balancing "normal" tyres needed much less fuss ). 18" was considered huge some years back. The calirabtion of these machines used has a fairly large range to stay within certified spec.
If you can accelerate through any wobble/judder then it will noramlly be end of line balancing which is the wheels, and in some cases can even be closer to the end of line balancing, and be the tyre itself.
And as per quote above , most dealers do the bare minium to keep their equipment insurance safe , let alone make them perform better. I should know I've serviced enough of them. I can spend 15 minutes just cleaning them up so they move and work properly!