Who uses Loctite?
Discussion
t out of it rather than go near Loctite. Binding calipers are a PITA!Some bolts used to hold calipers onto the hub are stretch bolts. The reason they might loosen is because they are re-used instead of being replaced.
If bolts are the correct part, in good condition and torqued correctly there's usually no need to use any form of thread lock and it could cause bigger problems later as others have said.
I'd make sure everything is clean before re-assembly and check your torque wrench is working properly before doing anything else.
If bolts are the correct part, in good condition and torqued correctly there's usually no need to use any form of thread lock and it could cause bigger problems later as others have said.
I'd make sure everything is clean before re-assembly and check your torque wrench is working properly before doing anything else.
Unstoppable said:
Changing the brakes on the Focus, is there any harm using Loctite? I've had a caliper bolt come loose before despite being torqued up properly, but how much of a pain will removing the bolt(s) be if I have used Loctite? (granted access is tight to begin with)
Which bolts do you mean?The ones holding the caliper to the caliper mounting or the ones that retain the slide pins?
Unstoppable said:
Changing the brakes on the Focus, is there any harm using Loctite? I've had a caliper bolt come loose before despite being torqued up properly, but how much of a pain will removing the bolt(s) be if I have used Loctite? (granted access is tight to begin with)
If Ford dosen't say to use Loctite, then you using it will just be a band aid. The bolt won't come lose if the parts are all OK & the job is done properly. e.g has the bolt been over torqued before ? is it the correct bolt ? threads ok ? copperease on the threads ? When was the torque wrench last calibrated ?
Wacky Racer said:
Loctite works on the principle that the seal breaks when moderate pressure is applied, so you should not have any problem, however if the braking system is involved best to seek specialised advice.
Depends on what Loctite you use , try moderate pressure on Loctite 648.
WhoseGeneration said:
So true, many don't appreciate that there are different grades of Loctite.
Screw, nut, stud, bearing, for starters.
Screw, nut, stud, bearing, for starters.
Loctite 276
Threadlocking - High strength, especially for nickel surfaces Threadlocker
Loctite 5188
Gasketing - For machined, rigid metal flanges - highly flexible
Loctite 2400
Threadlocking - Medium Strength Threadlocker "white" Material Safety Data Sheet
Loctite 2700
Threadlocking - High Strength Threadlocker “white” Material Safety Data Sheet
Loctite 586
Thread Sealant - For metal, high strength, excellent on brass sealant
Loctite 5610
Structural bonding - 2K silicone, very fast curing
Loctite 5615
Structural bonding - 2K silicone, fast cure
Loctite 5616
Structural bonding - 2K silicone, white version of Loctite 5615
Loctite 242
Threadlocking - Medium strenght, medium viscosity, general purpose threadlocker
Loctite 561
Thread Sealant - For metal threads (Stick)
Loctite 570
Thread Sealant - For metal, low strength, very slow curing threadsealant
Loctite 5980
Gasketing - Flange sealant, black, big gaps, label free
Loctite 662
Retaining - High strength, medium viscosity, also UV-curing retainer
Loctite 121078
Retainer - High strength, good temperature resistance, high viscosity retainer
Loctite F246
Structural bonding - General purpose
Loctite 3342
Structural bonding - High temperature
Loctite 3298
Structural bonding - Glass bonding
Loctite V5004
Structural bonding - Clear bondline
Loctite 3504
Structural bonding - Additional UV cure
Loctite F245
Structural bonding - Low odour
Loctite QB533
Structural bonding - Very fast curing
Loctite V1305
Structural bonding - Very fast curing
Loctite V1315
Structural bonding - Composite/plastic bonding
Loctite 5607
Structural bonding - 2K silicone, medium cure
Loctite 5612
Structural bonding - 2K silicone, higher temperature resistance
Loctite 9480
Structural bonding - 2K Epoxy, multible purpose bonder, food contact approved
Loctite 3455
Structural bonding - 2K Epoxy, fast, high viscosity
Loctite 8154
Lubrication - Anti-Seize, MoS2 assembly spray/paste
Loctite 8014
Lubrication - Anti-Seize, Food grade
Loctite 8191
Lubrication - Dry Film, general purpose
Loctite 8192
Lubrication - Dry Film, non metal surfaces
Loctite 8001
Lubrication - Oil, penetrating oil
Loctite 8011
Lubrication - Oil, chain lubricant
Loctite 8030
Lubrication - Oil, Cutting oil, bottle
Loctite 8031
Lubrication - Oil, Cutting oil, aerosol
Loctite 8105
Lubrication - Greases, general purpose
Loctite 8106
Lubrication - Greases, corrosion protection, general purpose
Loctite 8102
Lubrication - Greases, High temperature resistance
Loctite 8103
Lubrication - Greases, Heavy load applications
Loctite 8108
Lubrication - Greases, Food processing applications
Loctite 8101
Lubrication - Greases, Special purpose, chains, gears
Loctite 7255
Wearing Compounds - Sprayable wear resistant coating
Loctite 7117
Wearing Compounds - Brushable protective coating
Loctite 8005
Surface Treatment - Belt dressing
Loctite 7800
Surface Treatment - Corrosion protection, zinc spray
Loctite 7803
Surface Treatment - Corrosion protection, metal protection coating spray
Loctite 7100
Surface Treatment - Leak detector
Loctite 7414
Surface Treatment - Tamper proofing
Loctite 7400
Surface Treatment - Tamper proofing
Loctite 5080
Surface Treatment - Fix & Repair Tape
Loctite 7388
Surface Treatment - Activator Solvent based sold as kit with Loctite 330
Loctite 7091
Surface Treatment - Activator, solvent free
Loctite 5248
Light Cure Adhesive - Highly flexible, alcoxy silicone, ISO 10993 certified
Loctite 3103
Light Cure Adhesive - For stress sensitive plastics
Loctite 3105
Light Cure Adhesive - For stress sensitive plastics
Loctite 3345
Light Cure Adhesive - High humidity and chemical resistant, ISO 10993 certified
Loctite 3090
Instant Adhesive - Gap filling, 2-component, low bloom
Loctite 97057
Light Cure Equipment - Spot Cure System
Loctite 97058
Light Cure Equipment - Spot Cure System, UVA Wand System ECO
Loctite 97324
Light Cure Equipment - Light Guide 8mm x 1500 mm
Loctite 97325
Light Cure Equipment - Dual Light Guide 2x 3mm x 1500mm
Loctite 97327
Light Cure Equipment - Light Guide 8mm x 1000mm
Loctite 97120
Dispensing - Airline Filter Regulator
Loctite 97118
Dispensing - Advancing Slide with stroke 50mm
Loctite 97119
Dispensing - Advancing Slide with stroke 100mm
Loctite 98770
Light Cure Equipment - Dosimeter-Radiometer
Loctite 98002
Light Cure Equipment - Spot Radiometer
Loctite 97069
Light Cure Equipment - Spot Cure System, LED
Loctite 985246
Manual Dispensing Applicator - 490 ml Dual Cartridge Applicator, Acrylics
Loctite 985249
Manual Dispensing Applicator - 490 ml Dual Cartridge Pneumatic Applicator, Acrylics
Loctite SYS00706
Manual Dispensing Applicator - Dual Cartridge Pneumatic Applicator
Loctite 97048
Manual Dispensing Applicator - Dual Cartridge Pneumatic Applicator for Wearing Compounds Products
Loctite 97046
Manual Dispensing Applicator - For 300ml, 310ml Cartridges, Pneumatic
Loctite 96005
Manual Dispensing Applicator - For 50ml Cartridges, Elastic adhesives and sealants, gasketing products
Loctite 97207
Accessories Syringe - Clear Syringe Barrel Kit, 10ml
Loctite 97244
Accessories Syringe - Clear Syringe Barrel Kit, 30ml
Loctite 97263
Accessories Syringe - Black Syringe Barrel Kit for UV and INDIGO adhesives, 10ml
Loctite 97264
Accessories Syringe - Black Syringe Barrel Kit for UV and INDIGO adhesives, 30ml
Loctite 97208
Accessories Syringe - Syringe Airline Adapter, 10ml
Loctite 97245
Accessories Syringe - Syringe Airline Adapter, 30ml
Loctite 98463
Accessories Mixers and Nozzles - For acrylics, 10:1, 37ml
Loctite 984569
Accessories Mixers and Nozzles - For Epoxies, polyurethanes and silane modified polymers, 1:1, 2:1, 50ml
Loctite 5289010
Accessories Mixers and Nozzles - For acrylics, 1:1, 50ml
Loctite 1034575
Accessories Mixers and Nozzles - For acrylics, 10:1, 50ml
Loctite 984570
Accessories Mixers and Nozzles - For epoxies, 1:1, 2:1, 200ml, 400ml
Loctite 98457
Accessories Mixers and Nozzles - For silicones, 1:1, 2:1, 4:1, 400ml
Loctite 8953187
Accessories Mixers and Nozzles - For acrylics, 10:1, 490ml
Loctite 97229
Accessories Dispense Needles - Flexible dispense tips Polypropylene (PPF), 15 (= Amber) ID 1,37 mm
Loctite 97230
Accessories Dispense Needles - Flexible dispense tips Polypropylene (PPF), 18 (= Green) ID 0,84 mm
Loctite 97231
Accessories Dispense Needles - Flexible dispense tips Polypropylene (PPF), 20 (= Pink) ID 0,61 mm
Loctite 97232
Accessories Dispense Needles - Flexible dispense tips Polypropylene (PPF), 25 (= Red) ID 0,25 mm
Loctite 97221
Accessories Dispense Needles - Tapered dispense tips (PPC), 16 (= Grey) ID 1,19 mm
Loctite 97222
Accessories Dispense Needles - Tapered dispense tips (PPC), 18 (= Green) ID 0,84 mm
Loctite 97223
Accessories Dispense Needles - Tapered dispense tips (PPC), 20 (= Pink) ID 0,61 mm
Loctite 97224
Accessories Dispense Needles - Tapered dispense tips (PPC), 22 (= Blue) ID 0,41 mm
Loctite 97225
Accessories Dispense Needles - Stainless steel dispense tips standard (SSS), 15 (= Amber) ID 1,37 mm
Loctite 97226
Accessories Dispense Needles - Stainless steel dispense tips standard (SSS), 18 (= Green) ID 0,84 mm
Loctite 97227
Accessories Dispense Needles - Stainless steel dispense tips standard (SSS), 20 (= Pink) ID 0,61 mm
Loctite 97228
Accessories Dispense Needles - Stainless steel dispense tips standard (SSS), 25 (= Red) ID 0,25 mm
Loctite 97201
Dispensing - Footswitch
Loctite 8953426
Light Cure Equipment - UV protection glass, grey
Loctite 8953427
Light Cure Equipment - UV protection glass, orange
Loctite 8021
Lubrication - Oil, Silicone oil
Loctite 7701
Surface Treatment - Improve adhesion, for medical applications
Loctite 96001
Manual Dispensing Applicator - 50 ml Dual Cartridge Manual Applicator
Loctite 96003
Manual Dispensing Applicator - 200 ml Dual Cartridge Manual Applicator
Loctite 97001
Manual Dispensing Applicator - For 250ml bottle
Loctite 97002
Manual Dispensing - 300 ml Cartridge Pneumatic Dispenser
Loctite 97006
Dispensing - Digital Syringe
Loctite 97009
Dispensing - Integrated Semi-Automatic Dispensing System
Loctite 97034
Light Cure Equipment - Spot Cure System
Loctite 97039
Light Cure Equipment - Flood Cure System, UVALOC 400 Chamber
Loctite 97042
Manual Dispensing Applicator - 50 ml Dual Cartridge Manual Applicator
Loctite 97055
Light Cure Equipment - Flood Cure System, UVALOC 1000 Cure Chamber
Loctite 97152
Semi Automatic Dispensing System - Controller
Loctite 97108
Semi Automatic Dispensing System - Reservoir
Loctite 97113
Semi Automatic Dispensing System - Stationary Applicator Valve
Loctite 97114
Semi Automatic Dispensing System - Stationary Applicator Valve
Loctite 97115
Dispensing - Rotorspray
Loctite 97121
Dispensing Valve - Pinch Valve Applicator
Loctite 97130
Dispensing Valve - ErgoLoc
Loctite 97135
Semi Automatic Dispensing System - Diaphragm Valve
Loctite 97136
Semi Automatic Dispensing System - Diaphragm Valve
Loctite 97153
Dispensing - Multichannel Controller
Loctite 97323
Light Cure Equipment - Light Guide 5mm x 1500mm
Loctite 97326
Light Cure Equipment - Light Guide 5mm x 1000mm
Loctite 97328
Light Cure Equipment - Dual Light Guide 2 x 3mm x 1000mm
Loctite 98009
Semi Automatic Dispensing System - Light Cure Dispense Valve
Loctite 98013
Semi Automatic Dispensing System - Light Cure Dispense Valve
Loctite 98026
Manual Dispensing - For 25ml syringes
Loctite 98727
Light Cure Equipment - Dosimeter-Radiometer
Loctite 983437
Manual Dispensing Applicator - 200 ml Dual Cartridge Pneumatic Applicator
Loctite 983438
Manual Dispensing Applicator - 400 ml Dual Cartridge Manual Applicator
Loctite 983439
Manual Dispensing Applicator - 400 ml Dual Cartridge Pneumatic Applicator
Loctite 98414
Manual Dispensing - For 50ml bottle
Loctite 98548
Dispensing - Benchtop Peristaltic Dispenser
Loctite 262
Threadlocking - High/Med Strength Torque Tension Threadlocker
Loctite 601
Retaining- High strength, low viscosity, small gaps retainer
Loctite 640
Retaining - High strength, good temperature resistance, slow curing retainer
Loctite 649
Retaining - High strength, no acrylic acid retainer
Loctite 7204
Wearing Compounds - Chemically resistant floor protection
Loctite 7230
Wearing Compounds - High temperature & abrasion resistance
Loctite 7232
Wearing Compounds - High temperature wear resistant putty
Loctite 7256
Wearing Compounds - Bonding of ceramic tiles for wear protection
Loctite 7257
Wearing Compounds - Fast concrete repair solution
Loctite 128068
Gasketing - For machined, rigid metal flanges - semi flexible, very slow curing
Loctite 221
Threadlocking - Low strength, low viscosity, small threads Threadlocker
Loctite 222
Threadlocking - Low strength, general purpose Threadlocker
Loctite 241
Threadlocking - Medium strength, low viscosity, small threads threadlocker
Loctite 243
Threadlocking - Suitable for all metal threaded assemblies.
Loctite 245
Threadlocking - Medium strength, medium viscosity, large threads threadlocker
Loctite 248
Threadlocking - Medium strength threadlocker (stick)
Loctite 268
Threadlocking - High Strenght Threadlocker (Stick)
Loctite 270
Threadlocking - High Strength Threadlocker
Loctite 2701
Threadlocking - High strength, especially for chromated surfaces Threadlocker
Loctite 271
Threadlocking - High strength, low viscosity Threadlocker
Loctite 272
Threadlocking - High temperature, high strength Threadlocker
Loctite 275
Threadlocking - High strength, high viscosity, large threads Threadlocker
Loctite 277
Threadlocking - High strength, high viscosity, large threads Threadlocker
Loctite 278
Threadlocking - High Strength, high temperature Threadlocker
Loctite 290
Threadlocking - Penetrating Threadlocking Compound
Loctite 3011
Light Cure Adhesive - Fast surface cure, ISO 10993 certified
Loctite 3030
Structural bonding - PO bonder
Loctite 3038
Structural bonding - PO bonder
Loctite 3081
Light Cure Adhesive - Fast surface cure, ISO 10993 certified
Loctite 3106
Light Cure Adhesive - For stress sensitive plastics
Loctite 319
Structural bonding - glass-metal bonder
Loctite 3211
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 322
Light Cure Adhesive - Fast surface cure
Loctite 326
Structural bonding - Magnet bonder
Loctite 329
Structural bonding - Fast fixture
Loctite 3295
Structural bonding - General purpose
Loctite 330
Structural bonding - General purpose
Loctite 3301
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 3311
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 3321
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 3341
Light Cure Adhesive - Highly flexible, for soft PVC, ISO 10993 certified
Loctite 3381
Light Cure Adhesive - Highly flexible, high thermal cycle resistance, ISO 10993 certified
Loctite 3421
Structural bonding - 2K Epoxy, general purpose, long open time
Loctite 3423
Structural bonding - 2K Epoxy, multiple purpose, excellent for metal, good humidity resistance
Loctite 3425
Structural bonding - 2K Epoxy, multiple purpose bonder, excellent for bonding metals, for large surfaces
Loctite 3430
Structural bonding - 2K Epoxy, multible purpose bonder, fast, ultra clear
Loctite 3450
Structural bonding - 2K Epoxy, fast cure, ideal for metal repair
Loctite 3463
Metal-filled Compounds - 2K Epoxy, Kneadable
Loctite 3471
Metal-filled Compounds - 2K Epoxy, Putty
Loctite 3472
Metal-filled Compounds - 2K Epoxy, Pourable
Loctite 3473
Metal-filled Compounds - 2K Epoxy, Fast cure
Loctite 3474
Metal-filled Compounds - 2K Epoxy, Wear resistant
Loctite 3475
Metal-filled Compounds - 2K Epoxy, Multi purpose
Loctite 3478
Metal-filled Compounds - 2K Epoxy, High compressive strength
Loctite 3479
Metal-filled Compounds - 2K Epoxy, High temperature resistance
Loctite 3491
Light Cure Adhesive - High transparency, low yellowing
Loctite 3494
Light Cure Adhesive - High transparency, low yellowing
Loctite 350
Light Cure Adhesive - High humidity and chemical resistance
Loctite 352
Light Cure Adhesive - High humidity and chemical resistance, toughened
Loctite 3525
Light Cure Adhesive - Toughened, high strength
Loctite 3526
Light Cure Adhesive - Glass and plastic bonder with heat cure
Loctite 3554
Light Cure Adhesive - Fast cure, for coloured transparent substrates, ISO 10993 certified
Loctite 3555
Light Cure Adhesive - Very fast, for coloured transparent substrates, ISO 10993 certified
Loctite 3556
Light Cure Adhesive - Fast cure, for coloured transparent substrates, ISO 10993 certified
Loctite 366
Structural bonding - Additional UV cure
Loctite 382
Instant Adhesive - General purpose, gel
Loctite 3921
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 3922
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 3926
Light Cure Adhesive - High viscosity, for stress sensitive plastics, ISO 10993 certified
Loctite 3936
Light Cure Adhesive - For stress sensitive plastics, ISO 10993 certified
Loctite 401
Instant Adhesive - Universal, low viscosity
Loctite 4011
Instant Adhesive - Universal, low viscosity, ISO 10993 certified
Loctite 4014
Instant Adhesive - Plastics & rubber, capillary, ISO 10993 certified
Loctite 403
Instant Adhesive - Low bloom, low odour, medium viscosity
Loctite 4031
Instant Adhesive - Low bloom, low odour, medium viscosity, ISO 10993 certified
Loctite 406
Instant Adhesive - Low viscosity, plastics & rubber
Loctite 4061
Instant Adhesive - Plastics & rubber, low viscosity, ISO 10993 certified
Loctite 4062
Instant Adhesive - Plastics & rubber, capillary
Loctite 407
Instant Adhesive - High temperature, low viscosity
Loctite 408
Instant Adhesive - Low bloom, low odour, capillary
Loctite 409
Instant Adhesive - General purpose, gel
Loctite 410
Instant Adhesive - Toughened, black, high viscosity
Loctite 414
Instant Adhesive - General purpose, low viscosity
Loctite 415
Instant Adhesive - Metals, medium viscosity
Loctite 416
Instant Adhesive - General purpose, medium viscosity
Loctite 420
Instant Adhesive - General purpose, capillary
Loctite 4204
Instant Adhesive - High temperature, good impact resistance
Loctite 422
Instant Adhesive - General purpose, high viscosity
Loctite 424
Instant Adhesive - Plastics & rubber, low viscosity
Loctite 4304
Light Cure Adhesive - High strength, high plastic adhesion, low intensity cure, ISO 10993 certified
Loctite 4305
Light Cure Adhesive - high plastic adhesion, low intensity cure, ISO 10993 certified
Loctite 431
Instant Adhesive - Universal, medium viscosity
Loctite 435
Instant Adhesive - Toughened, clear
Loctite 438
Instant Adhesive - Toughened, black, fast
Loctite 454
Instant Adhesive - Universal, gel
Loctite 460
Instant Adhesive - Low bloom, low odour, low viscosity
Loctite 4601
Instant Adhesive - Low bloom, low odour, low viscosity, ISO 10993 certified
Loctite 480
Instant Adhesive - Toughened, black, fast
Loctite 4850
Instant Adhesive - Flexible, bendable, low viscosity
Loctite 4860
Instant Adhesive - Flexible, bendable, high viscosity
Loctite 493
Instant Adhesive - Metals, capillary
Loctite 495
Instant Adhesive - General purpose, low viscosity
Loctite 496
Instant Adhesive - Metals, low viscosity
Loctite 5083
Light Cure Adhesive - Highly flexible, acetoxy silicone
Loctite 5088
Light Cure Adhesive - Highly flexible, alcoxy silicone
Loctite 5091
Light Cure Adhesive - Highly flexible, acetoxy silicone
Loctite 510
Gasketing - For machined, rigid metal flanges - high temperature resistance
Loctite 511
Thread Sealant - For metal, low strength, general purpose thread sealant
Loctite 5145
Structural bonding - 1K silicone, electrical components
Loctite 515
Gasketing - For machined, rigid metal flanges - medium cure speed
Loctite 518
Gasketing - For machined, rigid metal flanges - semiflexible
Loctite 5203
Gasketing - For machined, rigid metal flanges - easy dissassembly
Loctite 5205
Gasketing - For machined, rigid metal flanges - semi flexible
Loctite 5208
Gasketing - For machined, rigid metal flanges - semi flexible
Loctite 5331
Thread Sealant - Recommended for plastic threads, metal-to-metal and plastic-to-metal substrate combinations.
Loctite 5366
Structural bonding - 1K silicone, general purpose
Loctite 5367
Structural bonding - 1K silicone, general purpose
Loctite 5368
Structural bonding - 1K silicone, general purpose
Loctite 5398
Structural bonding - 1K silicone, flowable
Loctite 5399
Structural bonding - 1K silicone, high temperature resistance
Loctite 5404
Structural bonding - 1K silicone, thermal conductive
Loctite 542
Thread Sealant - For fine metal threaded fittings, espacially hydraulic pipes
Loctite 549
Thread Sealant - For metal, high strength, slow curing thread sealant
Loctite 55
Thread Sealant - Pipe & Threadsealing Cord
Loctite 567
Thread Sealant - For metal, low strength, coarse threads Threadsealant
Loctite 5699
Gasketing - For flexible flanges, machined or casted surfaces, metal or plastic, excellent in water/glycol
Loctite 572
Thread Sealant - For metal, slow cure thread sealant
Loctite 573
Gasketing - For machined, rigid metal flanges - slow curing
Loctite 574
Gasketing - For machined, rigid metal flanges - general purpose
Loctite 577
Thread Sealant - Medium strength pipe sealant for metal threads.
Loctite 5772
Thread Sealant - For metal, especially for nuclear power plants threadsealant
Loctite 582
Thread Sealant - For metal, medium strength, fast curing threadsealant
Loctite 5900
Gasketing - Thixotropic paste, black, excellent in engine oils
Loctite 5910
Gasketing - For flexible flanges, machined or casted surfaces, metal or plastic
Loctite 5920
Gasketing - For flexible flanges, machined or casted surfaces, high temperature resistant
Loctite 5926
Gasketing - For flexible flanges, machined or casted surfaces, metal or plastic
Loctite 5940
Structural bonding - 1K silicone, high elongation
Loctite 5970
Structural bonding - 1K silicone, oil resistance
Loctite 603
Retaining - High strength, oil tolerant retainer
Loctite 620
Retaining - High strength, high temperature resistance retainer
Loctite 638
Retaining - High strength, general purpose retainer
Loctite 641
Retaining - Medium strength, if disassembly is required retainer
Loctite 648
Retaining - High strength, good temperature resistance retainer
Loctite 660
Retaining - High strength, gap fill for repair retainer
Loctite 661
Retaining - High strength, low viscosity, also UV-curing retainer
Loctite 675
Retaining - High strength, slow curing retainer
Loctite 7039
Cleaning - Cleaner spray for cleaning electrical contacts exposed to moisture or other contaminations
Loctite 7061
Cleaning - General purpose parts cleaner and degreaser (based on acetone) prior to bonding
Loctite 7063
Cleaning - General purpose parts cleaner and degreaser prior to bonding, which leaves no residue (solvent based)
Loctite 7070
Cleaning - Cleaner and degreaser for plastic parts prior to bonding, without risk of stress cracks
Loctite 7200
Cleaning - Gasket remover, which removes gasket sealants in 10-15 minutes
Loctite 7218
Wearing Compounds - Resist abrasion & corrosion
Loctite 7219
Wearing Compounds - High impact & abrasion resistance
Loctite 7221
Wearing Compounds - Chemically resistant coating
Loctite 7222
Wearing Compounds - Wear resistant putty
Loctite 7226
Wearing Compounds - Protection from fine particle abrasion
Loctite 7227
Wearing Compounds - Brushable protective coating
Loctite 7228
Wearing Compounds - White brushable protective coating
Loctite 7229
Wearing Compounds - High temperature protection from fine particle abrasion
Loctite 7234
Wearing Compounds - High temperature brushable coating
Loctite 7239
Surface Treatment - Improve adhesion, Plastic Primer
Loctite 7240
Surface Treatment - Activator, solvent free
Loctite 7386
Surface Treatment - Activator Solvent based
Loctite 7452
Surface Treatment - Accelerate, best cosmetic appearance
Loctite 7455
Surface Treatment - Accelerate, general purpose
Loctite 7457
Surface Treatment - Accelerate, ideal for stress cracking sensitive plastics
Loctite 7458
Surface Treatment - Accelerate, general purpose
Loctite 7471
Surface Treatment - Activator, solvent based
Loctite 7500
Surface Treatment - Rust treatment
Loctite 7649
Surface Treatment - Activator, solvent based
Loctite 770
Surface Treatment - Improve adhesion, plastic primer
Loctite 7840
Cleaning - Biodegradable cleaner and degreaser for removing grease, oil cutting fluids and workshop grime
Loctite 7850
Cleaning - General purpose hand cleaner based on natural extract
Loctite 7855
Cleaning - Hand cleaner for removing paint, resin and adhesive
Loctite 8007
Lubrication - Anti-Seize, copper, Aerosol
Loctite 8008
Lubrication - Anti-Seize, copper, brush top
Loctite 8009
Lubrication - Anti-Seize, long term protection
Loctite 8012
Lubrication - Anti-Seize, high load
Loctite 8013
Lubrication - Anti-Seize, high purity
Loctite 8023
Lubrication - Anti-Seize, high water resistance
Loctite 8040
Lubrication - Oil, Freeze & Release
Loctite 8065
Lubrication - Anti-Seize, copper, stick
Loctite 8104
Lubrication - Greases, Plastic part application
Loctite 8150
Lubrication - Anti-Seize, aluminium, can
Loctite 8151
Lubrication - Anti-Seize, Aluminium, Aerosol
Loctite 8201
Lubrication - Oil, general purpose, Five way spray
Loctite 9450
Structural bonding - 2K Epoxy, multiple purpose bonder, fast, gap filling, translucent
Loctite 9461
Structural bonding - 2K Epoxy, toughened, gap filling
Loctite 9464
Structural bonding - 2K Epoxy, toughened, gap filling, fast cure
Loctite 9466
Structural bonding - 2K Epoxy, toughened multiple purpose bonder, high bonding strength for all substrates
Loctite 9483
Structural bonding - 2K Epoxy, multiple purpose bonder, ultra clear, excellent for panels and displays
Loctite 9489
Structural bonding - 2K Epoxy, general purpose, extended working life
Loctite 9492
Structural bonding - 2K Epoxy, high temperature resistant
Loctite 9497
Structural bonding - 2K Epoxy, high temperature resistant, thermally conductive, excellent for bonding metal components
Loctite 9514
Structural bonding - 1K Epoxy, high temperature resistant, heat resistant bonding, toughened, high mechanical resistance
Total loss said:
smack said:
Red = 222 ?
Blue = 243 ?
In common usage yes, but you should really go by the No. as the colours are used for other strengths as well , e.g. green = 270 AND 648 which is VERY high strength. Blue = 243 ?
smack said:
Total loss said:
smack said:
Red = 222 ?
Blue = 243 ?
In common usage yes, but you should really go by the No. as the colours are used for other strengths as well , e.g. green = 270 AND 648 which is VERY high strength. Blue = 243 ?
, maybe the red referred to is not 222 but another one that is high strength ?Total loss said:
Yes your right,although 222 is more pink , maybe the red referred to is not 222 but another one that is high strength ?
Some manufacturers take the problem of which out by providing with, a set of pads, new slide pin bolts with thread locking compound on., maybe the red referred to is not 222 but another one that is high strength ?That seems a sensible approach.
Gassing Station | General Gassing [Archive] | Top of Page | What's New | My Stuff