gearbox removal help
gearbox removal help
Author
Discussion

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
After breaking something in my box at thunder road i have only just got round to properly starting to remove the gearbox. Ive had a few other things come up in the mean time which meant that the ro taken a back seat for a few weeks.

Right the problem i am having is the clutch line, according to the American forums there is a quick release on the clutch line, i am struggling to find it so am i blind, were the gto's different, or are the American's lying? The only two visible clutch connections on the gearbox that i can find are shown below in some very poor photography.

So my question is, do i disconnect the clutch line from one of the fittings in the photos, or do i go somewhere else?

Is it the nut connected to the hard pipe, and is the nut a standard 10mm nut not something that i need a special spanner for?



Or is it the fitting to the other side of this, i couldn't get a good photo as the camera wouldn't fit



Also please be kind as i am young and learning smile

neiljohnson

11,298 posts

238 months

Sunday 25th April 2010
quotequote all
Not 100% but think if you reach up to the end of the pipe you should find a clip to disconnect it. It wont be the end of the world if you disconnect it there though. Am going on experiance from other cars though.

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
Thanks for the very fast reply neil thumbup ,

also is it okay to leave the lower half of the rip shifter leaver in place. The bottom part that connects direct to the ripshifter?

Its just that the lower allen bolt is being a pain to remove.

neiljohnson

11,298 posts

238 months

Sunday 25th April 2010
quotequote all
gsd2000 said:
Thanks for the very fast reply neil thumbup ,

also is it okay to leave the lower half of the rip shifter leaver in place. The bottom part that connects direct to the ripshifter?

Its just that the lower allen bolt is being a pain to remove.
depends if it will allow enough clearance to swing the box out. If it looks like it will clear the floor ok then it will be ok if not then you could damage the floor or centre console when you lift the box out

crisisjez

9,209 posts

236 months

Sunday 25th April 2010
quotequote all
Try not to unscrew any bolt from the box if you can help it.
Thats a surefire way to tear the thread out the softer material.

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
Im still not 100% sure where to disconnect the clutch line from, the nuts seem seized but i dont want to break them

L2VXR

1,014 posts

244 months

Sunday 25th April 2010
quotequote all
gsd2000 said:
Im still not 100% sure where to disconnect the clutch line from, the nuts seem seized but i dont want to break them
This any help?


stevieturbo

18,105 posts

278 months

Sunday 25th April 2010
quotequote all
Does the Monaro even use a quick disconnect like the US cars ??

When I glanced at one, I didnt notice it.


Its blatantly obvious on mine ( US ) just where it enters the bellhousing. Monaro has hardline tube here for some odd reason.


And I find its easiest to remove box from car leaving bellhousing in place, then remove bellhousing.

L2VXR

1,014 posts

244 months

Sunday 25th April 2010
quotequote all
stevieturbo said:
Does the Monaro even use a quick disconnect like the US cars ??

When I glanced at one, I didnt notice it.


You may be right,this view from another holden manual shows a normal fitting like a brakeline that you would undo with a good quality spanner or a proper brake pipe spanner

[url]|http://thumbsnap.com/KoGP00Cf[/url]

this looks like yours, so undo it then remove the fork clip to retract the flexy pipe from the bracket

Edited by L2VXR on Sunday 25th April 22:25

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
thanks for the help everyone thumbup I will give monkfish a call in the morning and see what they say

MadMaxHSV

1,816 posts

229 months

Sunday 25th April 2010
quotequote all
Can confirm there is no quick release on the clutch line frown

I found the easiest place to get a spanner on the line, without the high risk of rounding the nut was at the master cylinder. You can then unbolt the braket in the transmission tunnel and take the whole lot out with the box.

Although I took the box out through the engine bay wink

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
MadMaxHSV said:
Can confirm there is no quick release on the clutch line frown

I found the easiest place to get a spanner on the line, without the high risk of rounding the nut was at the master cylinder. You can then unbolt the braket in the transmission tunnel and take the whole lot out with the box.

Although I took the box out through the engine bay wink
i did think about disconnecting at the master but i was trying to follow the destructions that the americans had on their forums. Well at least ive learnt that the american gearboxs have quick release fittings and uk gearboxs dont. I will see if the fish have any other options other than remove the engine with the box.

MadMaxHSV

1,816 posts

229 months

Sunday 25th April 2010
quotequote all
If you can get to all the transmission mount bolts you'll get it out the bottom no trouble.
As said, if you disconnect the clutch line from wherever (eg. master cylinder) the line will feed out with the box.

Just be careful lifting the box down, don't want to bend the output shaft or damage the splines. Transmission jack helps here.

gsd2000

Original Poster:

11,515 posts

214 months

Sunday 25th April 2010
quotequote all
Thanks for the tips MadMaxHSV, i have a tranmission jack as the box weighs more than me.

crisisjez

9,209 posts

236 months

Monday 26th April 2010
quotequote all
Wish mine did

monkfish1

12,522 posts

255 months

Monday 26th April 2010
quotequote all
No Quick release fitted. Far better to leave it connected though. Pull the box back far enough to undo the slave from the gearbox. That way you wont have to bleed it later

stevieturbo

18,105 posts

278 months

Monday 26th April 2010
quotequote all
monkfish1 said:
No Quick release fitted. Far better to leave it connected though. Pull the box back far enough to undo the slave from the gearbox. That way you wont have to bleed it later wink
Just make sure nobody puts their foot on the clutch !

Edited by stevieturbo on Monday 26th April 12:46

motomk

2,188 posts

275 months

Monday 26th April 2010
quotequote all
The newer Auto transmissioned cars have quick disconnects on them. Not much help on a manual!

Edited by motomk on Monday 26th April 13:13

granada203028

1,500 posts

228 months

Monday 26th April 2010
quotequote all
I agree on seporate the gearbox from the bell housing. This means the box will have to come straight back so the shifter will have to be removed.