Will These Wheel Specs Fit?
Will These Wheel Specs Fit?
Author
Discussion

after_shock

Original Poster:

8,751 posts

251 months

Friday 30th April 2010
quotequote all
Found some wheels I quite like however im concerned if they will fit or not!

Std specs:

19'
8' Wide
ET48 Offset

New Specs

19'
8.5' Wide
ET43 Offset

Concerns are with the extra width and slightly lower offset, I believe can still fit the exact same size tyres to the wheels, 245/35/19's even though they are slightly wider?

Any opinions!?

gsd2000

11,515 posts

214 months

Friday 30th April 2010
quotequote all
I woud say no, i have 18 x 8.5 +50 on the rear of mine and they look tight on the rear.

I know the americans run much wider wheels and claim to have no issues but how true this is i dont know

after_shock

Original Poster:

8,751 posts

251 months

Friday 30th April 2010
quotequote all
gsd2000 said:
I woud say no, i have 18 x 8.5 +50 on the rear of mine and they look tight on the rear.

I know the americans run much wider wheels and claim to have no issues but how true this is i dont know


In which way are yours tight as your offsett is in the opposite direction to the wheels that im looking at, inner suspension tight or wheel arch tight?

gsd2000

11,515 posts

214 months

Friday 30th April 2010
quotequote all
after_shock said:
gsd2000 said:
I woud say no, i have 18 x 8.5 +50 on the rear of mine and they look tight on the rear.

I know the americans run much wider wheels and claim to have no issues but how true this is i dont know
In which way are yours tight as your offsett is in the opposite direction to the wheels that im looking at, inner suspension tight or wheel arch tight?
it looks like a tight fit to the outer lip, i will get some measurements today and some pictures. I will do a proper check over the weekend if the weather is decent

after_shock

Original Poster:

8,751 posts

251 months

Friday 30th April 2010
quotequote all
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?

Trampy

143 posts

207 months

Friday 30th April 2010
quotequote all
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


You are the wrong way round mate

I have 8.5 with 45 offset and the tryes hit the lip on full travel.

Edited by Trampy on Friday 30th April 10:22

monkfish1

12,522 posts

255 months

Friday 30th April 2010
quotequote all
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


Wrong way round! 43mm offset with a 245 tyre is probably going to have you rubbing the rear arch near full bump. It will however at 5mm less offset depend very much on the exact shape of the tyre. If you did find one that could potentially clear, id suggest a rear end pac, and maybe even trailing arm bushes to keep the transverse movement to a minimum.

As ever, the only way to really prove it is to remove the springs and lower it to the bumpstops. With stock bushes you would want getting on for 8-10mm clearance all round, dropping to 5 ish if you did the bushes. Unless you go through this process, you cannot be sure.

There is a couple of mm to be trimmed from the rear arch.

gsd2000

11,515 posts

214 months

Friday 30th April 2010
quotequote all
monkfish1 said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?
Wrong way round! 43mm offset with a 245 tyre is probably going to have you rubbing the rear arch near full bump. It will however at 5mm less offset depend very much on the exact shape of the tyre. If you did find one that could potentially clear, id suggest a rear end pac, and maybe even trailing arm bushes to keep the transverse movement to a minimum.

As ever, the only way to really prove it is to remove the springs and lower it to the bumpstops. With stock bushes you would want getting on for 8-10mm clearance all round, dropping to 5 ish if you did the bushes. Unless you go through this process, you cannot be sure.

There is a couple of mm to be trimmed from the rear arch.
Is that all you have to do to check full wheel travel, pull the springs out and drop it down and have a good nose around at the space

gsd2000

11,515 posts

214 months

Friday 30th April 2010
quotequote all
Trampy said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?
You are the wrong way round mate

I have 8.5 with 45 offset and the tryes hit the lip on full travel.

Edited by Trampy on Friday 30th April 10:22
Dont you run 265 tryes aswell? Would it be best to run 255 tyres and gain a bit of room or is the offset too far off?

monkfish1

12,522 posts

255 months

Friday 30th April 2010
quotequote all
gsd2000 said:
monkfish1 said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


Wrong way round! 43mm offset with a 245 tyre is probably going to have you rubbing the rear arch near full bump. It will however at 5mm less offset depend very much on the exact shape of the tyre. If you did find one that could potentially clear, id suggest a rear end pac, and maybe even trailing arm bushes to keep the transverse movement to a minimum.

As ever, the only way to really prove it is to remove the springs and lower it to the bumpstops. With stock bushes you would want getting on for 8-10mm clearance all round, dropping to 5 ish if you did the bushes. Unless you go through this process, you cannot be sure.

There is a couple of mm to be trimmed from the rear arch.


Is that all you have to do to check full wheel travel, pull the springs out and drop it down and have a good nose around at the space


Yep! Bit more tedious to do at the front though! A wide tywrap works well for checking the areas you cant get to.

gsd2000

11,515 posts

214 months

Friday 30th April 2010
quotequote all
I only need to do the rear as the fronts on my bmw wheels are 18x8 +47 smile

Trampy

143 posts

207 months

Friday 30th April 2010
quotequote all
gsd2000 said:
Trampy said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


You are the wrong way round mate

I have 8.5 with 45 offset and the tryes hit the lip on full travel.

Edited by Trampy on Friday 30th April 10:22


Dont you run 265 tryes aswell? Would it be best to run 255 tyres and gain a bit of room or is the offset too far off?


255's still hit. There is an engineering company close to me that make parts for Pegeot rally and McLaren. They are going to look at the wheels to see if they can machine a couple of mm off the hub. Then I will get the grinder out and remove as much of the lip as possible. If the wheels can be machined then this should then give the space required at next to chuff all cost. If not, the wheels will be coming off.

after_shock

Original Poster:

8,751 posts

251 months

Friday 30th April 2010
quotequote all
gsd2000 said:
Trampy said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


You are the wrong way round mate

I have 8.5 with 45 offset and the tryes hit the lip on full travel.

Edited by Trampy on Friday 30th April 10:22


Dont you run 265 tryes aswell? Would it be best to run 255 tyres and gain a bit of room or is the offset too far off?


Currently on 255 tyres on the bacl which have never caught so could drop to 245 tyres to help a bit.

Could also take a touch out of the arches if needed to aswell, may just buy one wheel and see if it fits first lol

after_shock

Original Poster:

8,751 posts

251 months

Friday 30th April 2010
quotequote all
monkfish1 said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


Wrong way round! 43mm offset with a 245 tyre is probably going to have you rubbing the rear arch near full bump. It will however at 5mm less offset depend very much on the exact shape of the tyre. If you did find one that could potentially clear, id suggest a rear end pac, and maybe even trailing arm bushes to keep the transverse movement to a minimum.

As ever, the only way to really prove it is to remove the springs and lower it to the bumpstops. With stock bushes you would want getting on for 8-10mm clearance all round, dropping to 5 ish if you did the bushes. Unless you go through this process, you cannot be sure.

There is a couple of mm to be trimmed from the rear arch.


Cheers for the reply, the rear end pac is on the shopping list to be done this year as you didnt have the time on that Sat morning I was in, although you did end up doing all sorts of other things we were not expecting!

Is it the rear of the car I have to be more concerned about or the front?

monkfish1

12,522 posts

255 months

Friday 30th April 2010
quotequote all
after_shock said:
monkfish1 said:
after_shock said:
Just trying to get my head round which way the offsets go!!

So yours are ET50 which pushes them 2mm further outwards hence the tightness on the outer lip, correct??

If the ones I got are ET43 then they are 5mm further inwards on the car?

Or am I the wrong way round!?


Wrong way round! 43mm offset with a 245 tyre is probably going to have you rubbing the rear arch near full bump. It will however at 5mm less offset depend very much on the exact shape of the tyre. If you did find one that could potentially clear, id suggest a rear end pac, and maybe even trailing arm bushes to keep the transverse movement to a minimum.

As ever, the only way to really prove it is to remove the springs and lower it to the bumpstops. With stock bushes you would want getting on for 8-10mm clearance all round, dropping to 5 ish if you did the bushes. Unless you go through this process, you cannot be sure.

There is a couple of mm to be trimmed from the rear arch.


Cheers for the reply, the rear end pac is on the shopping list to be done this year as you didnt have the time on that Sat morning I was in, although you did end up doing all sorts of other things we were not expecting!

Is it the rear of the car I have to be more concerned about or the front?


There is a bit more clearance at the front then the rear.