SLP Oil Pump setup
Author
Discussion

MadMaxHSV

Original Poster:

1,816 posts

229 months

Saturday 1st May 2010
quotequote all
Anyone use one of these? Is it a good idea to fit the stiffer pressure relief valve spring to bump the pressure or is this unecessary/cause any problems?

scratchchin

mym8v8

9,468 posts

226 months

Saturday 1st May 2010
quotequote all
MadMaxHSV said:
Anyone use one of these? Is it a good idea to fit the stiffer pressure relief valve spring to bump the pressure or is this unecessary/cause any problems?

scratchchin


I think the extra volume is more important. The extra pressure could play havoc with your seals. Unless advised otherwise by an expert, I'm not fitting the high pressure spring in mine.

stevieturbo

18,105 posts

278 months

Saturday 1st May 2010
quotequote all
Havoc with what seals ? There arent any seals on an LS engine that are under pressure.
Apart from the oil filter seals themselves, and if you want to call them seals, the front and rear cam plates.
Amazingly, even the damn oil pump doesnt have a seal where it meets the block !

I just used a standard pump, although did shim it slightly. Dont run huge amounts of pressure though.
Strangely, the standard GM pump did appear to already have been ported when I opened it up. Maybe just newer OE pumps are like that ?

ARAF

20,759 posts

254 months

Saturday 1st May 2010
quotequote all
If some of the engines have a habit of firing the dipstick out of the block when cold, then this is one place where additional pressure may not be wanted.

stevieturbo

18,105 posts

278 months

Saturday 1st May 2010
quotequote all
ARAF said:
If some of the engines have a habit of firing the dipstick out of the block when cold, then this is one place where additional pressure may not be wanted.
Firing the dipstick out is crankcase pressure...not oil pressure.

In no way whatsoever could oil pressure ever force the dipstick out.

Blowby and inadequate crankcase ventilation could though.

MyM8V8

9,468 posts

226 months

Saturday 1st May 2010
quotequote all
[quote=stevieturbo]

the oil filter seals themselves, .


Dont run huge amounts of pressure though.
[quote]

Edited by MyM8V8 on Saturday 1st May 17:08

stevieturbo

18,105 posts

278 months

Saturday 1st May 2010
quotequote all
MyM8V8 said:
stevieturbo said:

the oil filter seals themselves, .


Dont run huge amounts of pressure though.
[quote]

Edited by MyM8V8 on Saturday 1st May 17:08
It would require horrendous oil pressure to burt the filter seals. Anyone running that much deserves damage to occur.
I would think hundreds of psi, as Ive seen plenty of engines of all shapes and sizes make 100+psi when cold and never damage the filters.

iacs_hsv

167 posts

261 months

Saturday 1st May 2010
quotequote all
While you've got the sump off to do your pump, take a look at the 90 degree drillings for the filter relay pipes (front sump). Mine were in a dreadful state from the factory CNC - need to port these out to get good flow to and from the filter. IMO, much more of a problem than the OEM machine work on the pump...

mym8v8

9,468 posts

226 months

Sunday 2nd May 2010
quotequote all
iacs_hsv said:
While you've got the sump off to do your pump, take a look at the 90 degree drillings for the filter relay pipes (front sump). Mine were in a dreadful state from the factory CNC - need to port these out to get good flow to and from the filter. IMO, much more of a problem than the OEM machine work on the pump...


Great positive help & advice Paul.

MadMaxHSV

Original Poster:

1,816 posts

229 months

Sunday 2nd May 2010
quotequote all
Well its on, kept to stock pressure.
As a side note, the Edelbrock two piece cover does not fit with this pump (even with plenty of grinding/clearancing)

Thanks for all the advice smile

MyM8V8

9,468 posts

226 months

Sunday 2nd May 2010
quotequote all
MadMaxHSV said:
Well its on, kept to stock pressure.
As a side note, the Edelbrock two piece cover does not fit with this pump (even with plenty of grinding/clearancing)

Thanks for all the advice smile
I got the QTP billet item. A lot dearer but a good piece and looking more like the stock cover shape. Do hope mine fits OK.

MyM8V8

9,468 posts

226 months

Sunday 2nd May 2010
quotequote all
stevieturbo said:
MyM8V8 said:
stevieturbo said:

the oil filter seals themselves, .


Dont run huge amounts of pressure though.
[quote]

Edited by MyM8V8 on Saturday 1st May 17:08
It would require horrendous oil pressure to burt the filter seals. Anyone running that much deserves damage to occur.
I would think hundreds of psi, as Ive seen plenty of engines of all shapes and sizes make 100+psi when cold and never damage the filters.
I suppose that would depend on how hot the motor got too. High temp and high pressure never too good together.