How do you lower the compression ratio of an engine?
How do you lower the compression ratio of an engine?
Author
Discussion

after_shock

Original Poster:

8,751 posts

251 months

Friday 7th May 2010
quotequote all
After discussing a few bits with the local engine place that im wanting doing yet again lower the compression ratio got mentioned, I breezed over that conversation as to be honest have not got a bloody clue what im talking about!

Tried looking on net but cant really see an actual answer so how do you actually lower the compression ratio of an LS engine?

Is it a complete re-build job or something much more simple to do!?

crisisjez

9,209 posts

236 months

Friday 7th May 2010
quotequote all
A thicker head gasket will do the job.
Bit Heath Robinson though.

stigmundfreud

22,454 posts

241 months

Friday 7th May 2010
quotequote all
several ways

best, get Low CR pistons
worst but easier get thicker head gaskets fitted

after_shock

Original Poster:

8,751 posts

251 months

Friday 7th May 2010
quotequote all
Changing the head gasket sounds a bit of a botch job, would it be reliable? lol Also would it not create too much space between the head and the rest of the engine?

Lower CR pistons will be a full bottom end re-build I take it?

MadMaxHSV

1,816 posts

229 months

Friday 7th May 2010
quotequote all
The middle road option is large chamber heads. 72cc heads should drop it a bit and be easier to acheive. Agree the best is dished pistons wink

gsd2000

11,515 posts

214 months

Friday 7th May 2010
quotequote all
317 casting heads are cheap 72cc heads. I think they came on the lq9 and lq4 engines. Suppose to flow the same as standard 243 casting heads.

stigmundfreud

22,454 posts

241 months

Friday 7th May 2010
quotequote all
the only real best way is the pistons anything else is a comprimise.

Boosted LS1

21,200 posts

291 months

Friday 7th May 2010
quotequote all
I've used 317's on builds. Basically an ls6 head but with big chambers and stock valves ie not hollow. Ideally you want a head that has a chamber diameter the same as your bore diameter. Looking at the aftermarket stuff you'll see that different chamber sizes are offerred. If using decent boost the proper way would be bowled forged pistons (try to keep the quench pad though)and a rebalance of the crankshaft if the piston weights are different to your original items.

The piston on the right is a very good design but is a custom made item.


neiljohnson

11,298 posts

238 months

Friday 7th May 2010
quotequote all
Best way is dished pistons other ways are spacer plates and 2 head gaskets, skim the pistons (not a good idea with standard lsx pistons though) or even shorter con rods (as in nobles) there are other ways but these are the ways i have dealt with in the past and tbh all have been reliable smile

after_shock

Original Poster:

8,751 posts

251 months

Friday 7th May 2010
quotequote all
What is the bore size of the standard block so I can look at heads that match?

I take it no one does dished pistons the exact same weight as the stock ones so dont need to strip it all down and balance the lot?

2woody

919 posts

241 months

Friday 7th May 2010
quotequote all
there's always the left-field answer - reduce the stroke a bit.

but, yes the more sensible answers are all here :-

deepen the combustion chambers in the head a tad
fit thicker head gaskets
fit dished pistons

.... and why are you wanting to do this ?

after_shock

Original Poster:

8,751 posts

251 months

Friday 7th May 2010
quotequote all
As im running FI and it keeps coming up in conversations about where to go next with the car, its not a definate thing to do just an idea that as I say keeps appearing and im wanting to look into it a bit more before make any decisions.

Would rather research a number of avenues before take the plunge and regret it!

stevieturbo

18,105 posts

278 months

Friday 7th May 2010
quotequote all
stigmundfreud said:
the only real best way is the pistons anything else is a comprimise.
Many would say adjusting cylinder head chamber size is the best way, not alwys the easiest though.

There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.


Easiest cheapest option is to drill a hole in the pistons. Might run a bit funny after though tongue out

behold81

2,931 posts

200 months

Saturday 8th May 2010
quotequote all
stevieturbo said:
stigmundfreud said:
the only real best way is the pistons anything else is a comprimise.


Many would say adjusting cylinder head chamber size is the best way, not alwys the easiest though.

There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.


Easiest cheapest option is to drill a hole in the pistons. Might run a bit funny after though


Is that just one at a time till the result is desired??? LOL

Mr2Mike

20,143 posts

286 months

Sunday 9th May 2010
quotequote all
[quote=stevieturbo
There is little wrong with using different gasket thickness to adjust CR, but the scope for adjustment is quite small. With modern steel shim gaskets, its little different than skimming lots off a head to increase CR.
[/quote]

Except you change the squish clearance, which might be quite important for a given application.

ringram

14,702 posts

279 months

Sunday 9th May 2010
quotequote all
If your pistons are stock now, then replacing them with dished ones is a no brainer.

after_shock

Original Poster:

8,751 posts

251 months

Sunday 9th May 2010
quotequote all
ringram said:
If your pistons are stock now, then replacing them with dished ones is a no brainer.


Yeah its starting to look that way!

Im definately going to change the heads when the car goes in for the next round of mods, been trying to avoid doing them and should have done them at the same time as the cam last year but given in and going to order some when (if) the exchange rate alters a bit.

J. J.

832 posts

248 months

Sunday 9th May 2010
quotequote all
Aftershock said
"so how do you actually lower the compression ratio of an LS engine?"

Why?? Seems hard work; am I missing something?

Boosted LS1

21,200 posts

291 months

Sunday 9th May 2010
quotequote all
^ I think he wants to run boost safely, ie not rely on good luck.

J. J.

832 posts

248 months

Sunday 9th May 2010
quotequote all
Thats what I thought, but still seems a stange way to get reliability. I would have thought that reducing the compresion ratio reduces the available power, and that to significantly reduce the compression ration would cost a lot of money because of the work involved. If it needs new pistons etc, then why not get the proper uprated jobbies? Is there that much difference in cost/reliability?