Some preliminary dash change questions please.
Some preliminary dash change questions please.
Author
Discussion

kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 19th May 2010
quotequote all
1)I've searched all the threads but unfortunately some of the links referred to on them are down/obsolete. What is the definitive online recource for the dashboard swap would you say for an early 1993 black buttoned Chim? (I've read the Chimaera resources one and have the bible yet I still can't find any of the 3 fcensoredg bolts)smile)

2) Where to source a replacement s/steel/ali dash..................the only 2 vendors I can find after searching online are Leven and the guy on PH

3) People talk in the archives about junking the 3 bolts (if you ever find the buggers) and replace with velcro when refitting dash top.................wives tale or pukka??.....sounds nice if true.

4)Replacing dial bulbs etc whilst dash is out seems sensible. Would you just use standard like for like bulbs or go the led/another route?.............does going led mean the fitment of other electrickery to use them safely?..............if so as Duncan would say "I'm out"smile

5)Any other "must do's whilst dash is off?

Many thanks once more lads............if I get answers for this lot I'll give you all some peace for a few days!!!

Cheers,
Kenny

.Mark

11,104 posts

307 months

Wednesday 19th May 2010
quotequote all
kenny.R400 said:
1)

3) People talk in the archives about junking the 3 bolts (if you ever find the buggers) and replace with velcro when refitting dash top.................wives tale or pukka??.....sounds nice if true.
Not noticed that, might be a good idea. If I ever get round to taking the top off mine I think I'd use wing nuts to secure - probably a bit more secure than velcro.

darkcat

2,354 posts

201 months

Wednesday 19th May 2010
quotequote all
3)

Mines loose anyway, really cant be bothered to re attach the nuts as its a 20 minute contortionist's job to do. It sits there quite happily with the bolts in their holes but no nuts.
I hadnt thought of velcro, sounds like a good idea, however would need to be very thin velcro.

tvrman

359 posts

315 months

Wednesday 19th May 2010
quotequote all
After just finishing my dash last weekend I can offer some tips.

Velcro won;t really do it on the passenger side, as the bolt needs to pull the top flush with the lower part. To put this bolt back on I had to use a few strips of gaffer tape to stick first the washer, then to help me turn the nut. It did the trick, but my hands still show the marks.

1. Do a search in this forum and chimaerapages.co.uk, there is advice everywhere.

To get the dashtop off, once the bolts are removed, lift the passenger side, so it touches the roof and then twist it away from the screen clockwise, which wiggling the dash and avoiding walnut veneer flicking into your face. Re-fitting is the opposite.

2. A steel dash is on ebay at the moment, have a look. I do have a MK1 Chimaera dash in the garage which you could buy for £20. It's a little rusty, but would clean up well or be fantastic for a template so you can make your own.

3. Don't bother, just put the nuts on finger tight and a bit of gaffer tape over the top, job done. (Easier if you find someone with small hands).

4. Have some spare bulbs in hand, but you never know you may find the odd one behind the dash not connected. I also changed by alarm light to a blue one and hid it behind my dash covering, looks smooth.....

5. Dust and clean the leather. Pop the dash top in the bath and give it two scrubs, it will need it, do the other leather while it is off. Clean all the connections are tight and give the relays a loving tap. Tape up anything that moves so you don;t get any further rattles.

Here is a picture of my final work. Took in total 19hours, which includes sanding the dash, painting the back of it and covering (okay I did have the TV on in the background). Almost worth it. Replacing a dash with a new one would take about 3 hours I would say.

Here is the finished article :


GTvr

173 posts

269 months

Wednesday 19th May 2010
quotequote all
most people have just replaced nuts with wingnuts, once youve worked out where they are and how to get to them you can remove the dash very quickly and easily.

kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 19th May 2010
quotequote all
Right lads many thanks, loved the pic too..gives me something to aim for.

Anyhow I've bit the bullet and dived in..........reading too much can sometimes talk you out of attacking it through fear..I was falling into that trap.

Anyhow dash top off and ready for phase 2.................funnily enough there was a pile of black foam bits on passenger side when removed........looked like a mouse had done it but no damage to wiring or any droppings....the foam covered a box (see pic).

So, in all it took me 20 minutes to remove top..........the first 2 bolts are exactly as described in the bible and a doddle with no cut hands or scrapes.

Third bolt was a bugger to find at first and I thought I'd got it ...............only to find I'd undone the bonnet release catchrolleyes..............a bit further up and there it was after removing heater duct and vent.


I'm taking pics and will post on a seperate thread in a day or two.

Thanks again guys.

Kenny.

PS Still don't know where to buy new dash from any ideas pleas

spend

12,581 posts

282 months

Wednesday 19th May 2010
quotequote all
Trimming down the studs and using hex bolts is the easiest IMHO. just use masking tape to hold washers & magnets/bluetack to keep nuts in 1/4" sockets that your fingers can manipulate. I have no idea what you gain with wing nuts - trying to start them is way beyond my dexterity.

If you strip your old dash you can get it recovered - or have a word with James at MADS he had a few & I'm sure he knows the particular dash clock/size (I don't think its like the 'mk1' pictures posted! - that looks to have smaller dials & later leds). TBH I made my own because there was so much confusion, I still have the original if you need a template (but I do want to keep it for posterity), as well as a plastic template I used to check my new layout (on the road).

tvrman

359 posts

315 months

drlloyd

145 posts

224 months

Wednesday 19th May 2010
quotequote all
I've done this job multiple times and can vouch for the use of 3 wing-nuts. This makes it much easier when removing the dash again in the future. They were M5 or M6. You can also use wing-nuts for the door panels.

Daniel

kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 19th May 2010
quotequote all
Thanks TVRMAN and Daniel.

Just took the plunge and ordered one from the nice lady Julie at Leven before I saw the link.

I will do the wing nut thing for sure! Leven reccomend 90 minute araldite for re gluing leds and suchlike, can anyone second that please?..I'll pick some up from B&Q when I get the wingiesthumbup

lesstatt

4,318 posts

221 months

Wednesday 19th May 2010
quotequote all
kenny.R400 said:
1)I've searched all the threads but unfortunately some of the links referred to on them are down/obsolete. What is the definitive online recource for the dashboard swap would you say for an early 1993 black buttoned Chim? (I've read the Chimaera resources one and have the bible yet I still can't find any of the 3 fcensoredg bolts)smile)

2) Where to source a replacement s/steel/ali dash..................the only 2 vendors I can find after searching online are Leven and the guy on PH

3) People talk in the archives about junking the 3 bolts (if you ever find the buggers) and replace with velcro when refitting dash top.................wives tale or pukka??.....sounds nice if true.

4)Replacing dial bulbs etc whilst dash is out seems sensible. Would you just use standard like for like bulbs or go the led/another route?.............does going led mean the fitment of other electrickery to use them safely?..............if so as Duncan would say "I'm out"smile

5)Any other "must do's whilst dash is off?

Many thanks once more lads............if I get answers for this lot I'll give you all some peace for a few days!!!

Cheers,
Kenny
I replaced all mine with LED bulbs from these guys, all you need to do is swop them over no probs. Im sure someone will know the bulb numbers and how many as they do vary for different gauges

I tried the Velcro method for a while but it rattled around and drove me mad so back to he nuts now, once you have found them once its very easy actually
http://www.ultraleds.co.uk/index.php?osCsid=3d8411...

Chimune

4,377 posts

254 months

Wednesday 19th May 2010
quotequote all
I was thinking about this task - i have had the dash off before to replace the washer tube y piece, and it wasnt too bad.

However, the bit that worries me is damaging the leds when removing them and the removal of the dials. Anyone got any hints on these procedures ?

<edit> i see this kit on ebay: http://tinyurl.com/39h926q claims to be the heater leds. Anyone used it, and are they really that hard to purchase separately ?

I also have a mate who is 'really into veneer' and wants to do the wood for me. I want to see him do a trial run 1st - so has anyone got an old dash they no longer want ?

Edited by Chimune on Wednesday 19th May 17:29

kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 19th May 2010
quotequote all
Thanks for the tip and link Lesthumbup.will follow that up now!!!!!

Chim, the leds came off easily, they were bonded but easly taken off with light but firm pressure.

Only bugger is now I'm a bit missing, it's one of those stupid little brackets that holds the haazzard warning light button and indicator lights bracket and is bonded to back of radio panel................wonder where I'll source one of them for tomorrow??

MADMAX2

2,336 posts

225 months

Wednesday 19th May 2010
quotequote all
kenny.R400 said:
Thanks for the tip and link Lesthumbup.will follow that up now!!!!!

Chim, the leds came off easily, they were bonded but easly taken off with light but firm pressure.

Only bugger is now I'm a bit missing, it's one of those stupid little brackets that holds the haazzard warning light button and indicator lights bracket and is bonded to back of radio panel................wonder where I'll source one of them for tomorrow??
go to B & Q and look for set of brackets for windows or try to it up as close as u can!

kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 19th May 2010
quotequote all
thumbup

blueseven

27 posts

225 months

Tuesday 14th September 2010
quotequote all
Hi Kenny.

Can you remember how many of each type of instrument bulb is needed? Planning on replacing my dash and want to get LED bulbs before I start.

Cheers

Gav.

SILICONE KID

14,997 posts

262 months

Tuesday 14th September 2010
quotequote all
.Don`t forget to mask off above the top dash,the treaded bar will spring out and rip it.I can remove mine and put it back in ten minutes.If you did airfix as a kid you will be fine.


kenny.R400

Original Poster:

1,212 posts

271 months

Wednesday 15th September 2010
quotequote all
Gav, I just replaced gauge bulbs with like for like for ease, sure there was just one per gauge but hopefully someone may correct me if I'm wrong there.

The warning lights, ie indicators,main beam etc. were replaced with these, they are hidden behind the smoked plasic covers, think there were 9 off. This is what I used http://www.vintagecarparts.co.uk/en/3127~panel+war...

Only problem was I had to fettle them as they stood prouder than old ones and covers wouldn't sit flush at first..........and old covers weren't interchangeable with new bulbs...sorted now though.

I also took lads advice here and replaced the 3 dash retaining nuts with wing nuts, well worth it and easy to put back then. I had to take dash out one more time as well so they came into their own!!!!!

Only problems I had on removal was finding the "3rd" nut on drivers side. Thought I'd got the bastrad and had a go at removing dash.............t'was only when I saw my bonnet pull dangling I realised I'd detatched its bracket insteadmad

Have a drive of car when completed with dash top off, in fact leave it off for a day or so.........I was too cocky and built it back up after a quick test.........had to whip it off again after spotting a fault but wingnuts saved a lot of grief.

All the best with it, not as bad as a job as you'd think.

Kenny

DODY37

45 posts

207 months

Thursday 16th September 2010
quotequote all
Kenny
Thats a mouse, had the same in my 450!
Set some traps in the car see what you get! thought my garage air tight, was not!!

markreilly

795 posts

203 months

Friday 17th September 2010
quotequote all
www.sc-power.com will make you a bespoke dash