Anyone used Arch Enemies?
Anyone used Arch Enemies?
Author
Discussion

boggie

Original Poster:

393 posts

253 months

Sunday 23rd May 2010
quotequote all
Hi All,

I have been trying rime this weekend and have come across a set of BMW X5 19x9 ET48 and 19x10 ET45 rims with 245/35 fronts and 265/30 rears. With a 5mm spacer the fronts will clear the strut by 3 or 4mm. The rear rims will easily clear on their inside as there is around 30mm clearance with the standard 8J ET48 rims. The outside of both front and rear is where I am going to experience difficulties. On the front the outside edge will be 17.5mm further out than standard and the rears will be 18mm. So, Ideally I would like to roll the rear arch return edge and slightly flare the fronts.

I have been talking to a guy who used Arch Enemies to roll and slightly flare his rear arches. He said they did this for £75 using a hot air gun and an arch rolling machine. The results gave him an extra 20mm and there was no paint damage, they even removed and extended his arch liners to fit for an extra tenner. I would also consider getting a more serious flare to the rear wheel arches, perhaps 50mm or more, fitting 12" rims and repainting. Maybe in the future. Has any of you experienced their work first hand?

gsd2000

11,515 posts

214 months

Sunday 23rd May 2010
quotequote all
S800vxr has, i think

S800VXR

5,877 posts

231 months

Sunday 23rd May 2010
quotequote all
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! smile

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!

boggie

Original Poster:

393 posts

253 months

Sunday 23rd May 2010
quotequote all
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that!

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!


Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?

Thanks,
B

the_ferret82

25,627 posts

215 months

Monday 24th May 2010
quotequote all
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! smile

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?

Thanks,
B
other option for bigger rubber is VXR8 wheels and a mini tub from the fish. ill be corrected if im wrong here but you can then get 285 tires on...

007 VXR

64,187 posts

218 months

Monday 24th May 2010
quotequote all
the_ferret82 said:
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! smile

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?

Thanks,
B
other option for bigger rubber is VXR8 wheels and a mini tub from the fish. ill be corrected if im wrong here but you can then get 285 tires on...
yes fish did mine smile


Edited by 007 VXR on Monday 24th May 09:59

boggie

Original Poster:

393 posts

253 months

Monday 24th May 2010
quotequote all
At the risk of sounding stupid but throwing caution to the wind..... what is a mini tub? I was thinking Ben and Jerry's.

the_ferret82

25,627 posts

215 months

Monday 24th May 2010
quotequote all
its having the arches cut inwards by a small ammout to allow bigger wheels to be fitted. "full" tubbing is what is done on drag cars.

boggie

Original Poster:

393 posts

253 months

Monday 24th May 2010
quotequote all
Thanks for enlightening me! Sounds an expensive job though.

the_ferret82

25,627 posts

215 months

Monday 24th May 2010
quotequote all
boggie said:
Thanks for enlightening me! Sounds an expensive job though.
according to 007 aobut 2k but well worth it..

boggie

Original Poster:

393 posts

253 months

Monday 24th May 2010
quotequote all
I guess it is a fair price but I quite like the idea of flaring the rear arches if it is possible. THe worse case scenario would be some minor bodywork and rear quarter repaint. This would be a lot cheaper than tubbing and might look rather good too, especially filled with 19x10 rims and 285/30 rubber....

the_ferret82

25,627 posts

215 months

Monday 24th May 2010
quotequote all
each to there own and all that. i suggest you take a look on the yank fourms LS1 as i think there is a few that have done this..

Magic919

14,592 posts

232 months

Monday 24th May 2010
quotequote all
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! smile

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?

Thanks,
B
Bear in mind someone else used Arch Enemy (after Roger had) and they rolled the rear arches and needed zero paint work afterwards.

See here for thread - http://www.pistonheads.com/gassing/topic.asp?h=0&a...

boggie

Original Poster:

393 posts

253 months

Monday 24th May 2010
quotequote all
Hmmm. Very interesting, thanks!

Do you happen to know what extra room he got? I would imagine the fronts, being single skin, will be easy to flare slightly without paint damage. What I might do on the rears is get them to just roll the lip, if the paint gets damaged then go for a nice flare too.

S800VXR

5,877 posts

231 months

Monday 24th May 2010
quotequote all
Someone else has used AE but they only rolled the lips a little. If you want 10" on the rear (Bonnie! laugh) then you need to role totally flat! I also thought about flaring but the rears just to thick, you could stretch it a little as I did but in the end you will just start buckling the outter skin. The fronts dont need flaring, 9" will go on if your carefull.

9.5" will go out back I think with a little roll and the right offset, something around the 50 mark id guess, Tubbing whilst nice is really pointless IMHO unless you really want VXR8 wheels (big offset) and even then you could simply fit spacers to move the wheel out into the available space. If you do tub though I know the fish do a superb job from what Ive seen.

MyM8V8

9,468 posts

226 months

Monday 24th May 2010
quotequote all
Magic919 said:
boggie said:
S800VXR said:
Yes - used him. He is very carefull but the Ro arches will not roll enough without damaging the outside metal which then means you will need to have bodywork done. Also if you want to fit 10" rims you WILL need to have the lips roilled totally flat! been there done that! smile

The jap cars he deos have thin single skin metal which rolls easy, the RO has multiple layers which are spot welded together so very strong! You have been warned!
Thanks! If I were instead to fit 9" ET48 rears with 265/30 tyres, do you think I would need to roll the rears so much that it would involve paint?

Thanks,
B
Bear in mind someone else used Arch Enemy (after Roger had) and they rolled the rear arches and needed zero paint work afterwards.

See here for thread - http://www.pistonheads.com/gassing/topic.asp?h=0&a...
Chris had the GTS done as well and the outer skins are slightly rippled, so be careful.

after_shock

8,751 posts

251 months

Monday 24th May 2010
quotequote all
If im not mistaken are the VXR8 wheels not incredibly heavy in comparison with the Ro alloys?

007 VXR

64,187 posts

218 months

Monday 24th May 2010
quotequote all
after_shock said:
If im not mistaken are the VXR8 wheels not incredibly heavy in comparison with the Ro alloys?
the back ones are , but their bigger
fronts are about the same smile