Monaro front jacking points
Discussion
Has anyone strengthened the front jacking points on a monaro yet?
It's just that as part of my upgrades to my ro, i am fully stripping the old underseal off the car and tidying everything up, applying seam sealer and resealing.
My front jacking points have got a bit mangled over the years, its a 2004 car, and the sideskirts hide the damage.
This is what they look like generally cleaned up and no side skirts


Has anyone added any strengthening plates to the jacking points?
Any tips to straighten them out?
Both sides look about the same damage wise
Thankyou
It's just that as part of my upgrades to my ro, i am fully stripping the old underseal off the car and tidying everything up, applying seam sealer and resealing.
My front jacking points have got a bit mangled over the years, its a 2004 car, and the sideskirts hide the damage.
This is what they look like generally cleaned up and no side skirts


Has anyone added any strengthening plates to the jacking points?
Any tips to straighten them out?
Both sides look about the same damage wise
Thankyou
Every car Ive owned has had shyte jacking points. When will manufacturers realise garages dont generally care how they jack and home users use simple trolley jacks, neither have a nice U shapped cup for fitting properly. If your going to modify the area Id suggest a nice big flat reinforced area for either a 4 poster pad or a trolly jack foot to press against. 

Evening all.
I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.
I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.




I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.
Edited by snowwolf on Tuesday 1st June 21:06
granada203028 said:
Mine look a bit ragged too 
How is your gearbox?
still ongoing, red victor pulled it out a bit but was busy. I did tell him before he started that i can get another one, so i think he may have left it by purpose so i can put it back together, as the will accept it as exchange as long as its in one piece.
How is your gearbox?
Just need to "borrow" my dads car so i can get some scrap metal and "borrow" my uncles welder to make a frame. Bolt it to the case and drop a puller from it. Thats the plan for the weekend.
Red victor said that one of my bearings has disintergrated an bits of the case are on the magnets and some of the balls are missing. I think its the main bearing in the middle of the case but i cant check myself as i havent got a small enough mirror.
Either way i will decide which way to go on monday, monkfish rebuild or my own.
snowwolf said:
Evening all.
I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.
I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.




thats brilliant. Im using blocks of wood on my axle stands which are okay but i was trying to think of something better and i think you have done. I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.
Edited by snowwolf on Tuesday 1st June 21:06
I would have thought some foam or rubber secured to the top of the stand to protect the paint on the to a bit better.
gsd2000 said:
snowwolf said:
Evening all.
I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.
I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.




thats brilliant. Im using blocks of wood on my axle stands which are okay but i was trying to think of something better and i think you have done. I think the jacking points of the car are really unsafe to be honest and should be used with caution!
There is an area behind the jacking paints that I have expertly shaded in on the photo
that I use to jack my car up on, I have a 6mm thick steel plate that fits that area, my plates are 4" x 7" and they are placed on that area and use hyd trolly jacks to lift the car, I never just use one lifting point, ie both front jacking points or both back points or front and back on one side, the rear points for the trolly jacks are where the big chassis bolt is, you can't miss it when you look under the rear where the original jacking point is.I have also made some axle stand mods so that can be put on the main sub frame and fit just right, I have had the whole car up off the ground in this way and is really safe.
Edited by snowwolf on Tuesday 1st June 21:06
I would have thought some foam or rubber secured to the top of the stand to protect the paint on the to a bit better.

snowwolf said:
As your a man of home servicing, I will make you some if you like, will see what metal I have at work tomorrow, if you want the chassis rail axle stand mounts, I will need to know what size tube your axle stands use?
thanks snow wolf i will get some sizes for you later. Gassing Station | HSV & Monaro | Top of Page | What's New | My Stuff



