Does my MAF need cleaning?
Does my MAF need cleaning?
Author
Discussion

boggie

Original Poster:

393 posts

253 months

Monday 7th June 2010
quotequote all
Has anybody attempted cleaning their MAF? I asked this question because my car has been fitted with a K&N filter by a previous owner. These pre-oiled filters, whilst giving good airflow, are known to affect MAF sensors in certain cars. For example I know of a number VAG 20V Turbo engines that when fitted with K&N filters needed the MAF sensor cleaning or even replacing.

There are specific products for cleaning MAF sensors, such as CRC 05110 that are designed to remove all sorts of contaminants, particularly from oil ‘blow through’. See here:

http://www.youtube.com/watch?v=vPT8rL0noYg

Have any of you tried similar products with any success?

Seems to make sense and is quite cheap but has anyone tried it?

Thanks,
B


Edited by Boggie on Sunday 12th June 14:54

monkfish1

12,522 posts

255 months

Monday 7th June 2010
quotequote all
Id say you have an air leak post the MAF.

nosubstitute

750 posts

213 months

Monday 7th June 2010
quotequote all
This is very interesting for me because I too have developed an idling issue where sometimes it seems the engine might stall and at the weekend I got a 'check engine' message. Coincidence?

boggie

Original Poster:

393 posts

253 months

Tuesday 8th June 2010
quotequote all
monkfish1 said:
Id say you have an air leak post the MAF.



Hi Roger,

Grateful for your input. That was my first thought too but the gas guys had a solvent spray that they used all over the head, inlet and injector area whilst watching the Lanbda output. It seemed a good test and did not affect the results. Is the MAF a possible issue considering the car has a K&N or am I off the mark and should look elsewhere?

Cheers,
B

Boosted LS1

21,200 posts

291 months

Tuesday 8th June 2010
quotequote all
The hotwire is self cleaning. Millions of cars run hot wire without the need for cleaning. Is the monaro in some way different?

monkfish1

12,522 posts

255 months

Wednesday 9th June 2010
quotequote all
Agreed. Never seen this occur yet on these cars. Dont think i ever will.
Yes, defo look elsewhere.

Edited by monkfish1 on Wednesday 9th June 09:02

eliot

12,000 posts

285 months

Wednesday 9th June 2010
quotequote all
Boosted LS1 said:
The hotwire is self cleaning. Millions of cars run hot wire without the need for cleaning. Is the monaro in some way different?
MAF's (Bosch) on BMW's seem to need cleaning. Had surging problems around the mid-range - was told to drive it with the MAF disconnected to proove - which it did, so took it to bits and cleaned it and problem was solved.

Boggie

Original Poster:

393 posts

253 months

Wednesday 9th June 2010
quotequote all
I had a similar issue (uneven idle and surging at low load mid range) early in TT ownership after fitting a K&N. Audi blamed the K&N fitted a new MAF and standard filter which seemed to cure it. I posted the question on the Audi forum and found others who had experienced the same failure after fitting pre-oiled filters. That was a Bosch unit too.

This is why I suspected the K&N had 'oiled' my MAF on the Monaro but I guess Roger, you have seen quite a few of these cars with K&N over the years so if they were trouble free I will have to look elsewhere.

Cheers,
B

Boosted LS1

21,200 posts

291 months

Wednesday 9th June 2010
quotequote all
eliot said:
Boosted LS1 said:
The hotwire is self cleaning. Millions of cars run hot wire without the need for cleaning. Is the monaro in some way different?
MAF's (Bosch) on BMW's seem to need cleaning. Had surging problems around the mid-range - was told to drive it with the MAF disconnected to proove - which it did, so took it to bits and cleaned it and problem was solved.
Then it was probably a faulty maf. When you switch on the ignition the hotwire receives a zillion volts (give or take a few) which cooks off any contaminants. This is the cleaning process. If the hotwire's not heated automatically then the maf has a fault and should be replaced.

doleboy

747 posts

248 months

Wednesday 9th June 2010
quotequote all
Also worth having a peak to see if the MAF or mesh is damaged. Mine was before I got rid of it.

eliot

12,000 posts

285 months

Wednesday 9th June 2010
quotequote all
Boosted LS1 said:
eliot said:
Boosted LS1 said:
The hotwire is self cleaning. Millions of cars run hot wire without the need for cleaning. Is the monaro in some way different?
MAF's (Bosch) on BMW's seem to need cleaning. Had surging problems around the mid-range - was told to drive it with the MAF disconnected to proove - which it did, so took it to bits and cleaned it and problem was solved.
Then it was probably a faulty maf. When you switch on the ignition the hotwire receives a zillion volts (give or take a few) which cooks off any contaminants. This is the cleaning process. If the hotwire's not heated automatically then the maf has a fault and should be replaced.
surely if the wire wasn't heated - it wouldn't work-all. Quite a recognised procedure in bmw circles, especially M5 owers who have two mafs.

ringram

14,702 posts

279 months

Wednesday 9th June 2010
quotequote all
vomit

If you dont have a MAF you wont need to clean it, or troubleshoot it, or care about it.

Boosted LS1

21,200 posts

291 months

Thursday 10th June 2010
quotequote all
eliot said:
Boosted LS1 said:
eliot said:
Boosted LS1 said:
The hotwire is self cleaning. Millions of cars run hot wire without the need for cleaning. Is the monaro in some way different?
MAF's (Bosch) on BMW's seem to need cleaning. Had surging problems around the mid-range - was told to drive it with the MAF disconnected to proove - which it did, so took it to bits and cleaned it and problem was solved.
Then it was probably a faulty maf. When you switch on the ignition the hotwire receives a zillion volts (give or take a few) which cooks off any contaminants. This is the cleaning process. If the hotwire's not heated automatically then the maf has a fault and should be replaced.
surely if the wire wasn't heated - it wouldn't work-all. Quite a recognised procedure in bmw circles, especially M5 owers who have two mafs.
There's normal working heat and burn off heat. The latter is so hot, maybe 1000 degrees it burns contaminants off the wire. I think burn off is when the engine is switched off not when started. When started the sensor registers ambiant temp and makes the wire temp a fair bit higher then when you get air flow it can measure the voltage change.