WARNING! The Horn Is Imminent.
WARNING! The Horn Is Imminent.
Author
Discussion

MEATANDCHEESE

Original Poster:

409 posts

198 months

Sunday 13th June 2010
quotequote all











Just bought one of these for the interior...hehe








007 VXR

64,187 posts

218 months

Sunday 13th June 2010
quotequote all
looking good

smile

always feels strange looking at an evoke r8 with no orange on it scratchchin


hehe

MEATANDCHEESE

Original Poster:

409 posts

198 months

Sunday 13th June 2010
quotequote all
007 VXR said:
looking good

smile

always feels strange looking at an evoke r8 with no orange on it scratchchin


hehe
Cheers M8

You busy?

We are ABSOLUTELY Rammed here!

007 VXR

64,187 posts

218 months

Sunday 13th June 2010
quotequote all
MEATANDCHEESE said:
007 VXR said:
looking good

smile

always feels strange looking at an evoke r8 with no orange on it scratchchin


hehe
Cheers M8

You busy?

We are ABSOLUTELY Rammed here!
all good smile has been busy . calming down now

Magic919

14,595 posts

232 months

Sunday 13th June 2010
quotequote all
Will be even better looking once the de-badging reaches the rear of the car.

MEATANDCHEESE

Original Poster:

409 posts

198 months

Sunday 13th June 2010
quotequote all
^

It's on the cards for next week.

Really hot hair dryer and some patience I reckon.

Any tips??

Magic919

14,595 posts

232 months

Sunday 13th June 2010
quotequote all
Warm sun is usually enough. You can prise it off with your fingers if you are sensible. Bit of floss under one edge to get it started. Then some solvent to remove any remainder of the glue/foam.

Monaro5.7

7,337 posts

210 months

Sunday 13th June 2010
quotequote all
Magic919 said:
Warm sun is usually enough. You can prise it off with your fingers if you are sensible. Bit of floss under one edge to get it started. Then some solvent to remove any remainder of the glue/foam.


I used a bit wire from ma strimmer lol worked it in behin the badges and it cut throw the foam pads that hold them on. Ofcourse the wire was not attached 2 the strimmer at the when did it lol. The some solvent and to remove the worst of the foam pad left behind then some tar and glue remover worked a treat laugh

Magic919

14,595 posts

232 months

Sunday 13th June 2010
quotequote all
There you go. Now you have it in two different languages.

007 VXR

64,187 posts

218 months

Sunday 13th June 2010
quotequote all
Magic919 said:
There you go. Now you have it in two different languages.
rofl

ARAF

20,759 posts

254 months

Sunday 13th June 2010
quotequote all
007 VXR said:
Magic919 said:
There you go. Now you have it in two different languages.
rofl
laugh

My strimmer wire would be too thick. Dental floss works very well.

MEATANDCHEESE

Original Poster:

409 posts

198 months

Tuesday 15th June 2010
quotequote all
Magic919 said:
Will be even better looking once the de-badging reaches the rear of the car.
How's That?




ARAF

20,759 posts

254 months

Tuesday 15th June 2010
quotequote all
That's cleaner. Did you use strimmer wire? and how did you hold the strimmer to use it without scratching the paint?

gsd2000

11,515 posts

214 months

Tuesday 15th June 2010
quotequote all
ARAF said:
That's cleaner. Did you use strimmer wire? and how did you hold the strimmer to use it without scratching the paint?
hairdryer and dental floss works well and doesnt scratch the paint

MEATANDCHEESE

Original Poster:

409 posts

198 months

Tuesday 15th June 2010
quotequote all
gsd2000 said:
ARAF said:
That's cleaner. Did you use strimmer wire? and how did you hold the strimmer to use it without scratching the paint?
hairdryer and dental floss works well and doesnt scratch the paint
Gave it a quick wash to get off surface dirt, then heated up with a hairdryer.

Got about six inches of floss and just worked it back and forth.

Broke about three times but removed in the end.

Then got off the remaining sticky stuff with the hairdryer and a rubber glove.

A toffee wheel would have been quicker but I don't have one!

I really like the clean look.

I intially left the VXR8 badge, but that went as well in the end.

I am using the same PH design on the wheel centres to finish it off. (REALLY confuse folk!)hehe


Just spent the afternoon changing the brake fluid as Picador forgot to do it and I couldn't be arsed taking it back plus I know it's been done properly.

Also cleaned and polished the calipers and wheels at the same time.

Edited by MEATANDCHEESE on Tuesday 15th June 19:43