If your dragging your car get your doughnuts checked!!!
If your dragging your car get your doughnuts checked!!!
Author
Discussion

MyM8V8

Original Poster:

9,468 posts

226 months

Saturday 19th June 2010
quotequote all
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.

I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.

Now this has happened the next thing will have to be a prop loop.

stevieturbo

18,107 posts

278 months

Saturday 19th June 2010
quotequote all
MyM8V8 said:
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.

I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.

Now this has happened the next thing will have to be a prop loop.
If you have a 2 piece prop.....if there is any point fitting a loop at all, there will need to be more than one.

Although fairly sure that most donut setups even if the donut completely fails, the shaft itself still shouldnt be able to drop ?

Best option is just a setup with no rubber.

Edited by stevieturbo on Saturday 19th June 17:44

MyM8V8

Original Poster:

9,468 posts

226 months

Saturday 19th June 2010
quotequote all
stevieturbo said:
MyM8V8 said:
Just had the old girl up on the lift today for Dave to weld up a track exhaust. While up there I gave her the once over and noticed that the front doughnut is shagged, obviously due to dead hooking at the Pod last week.

I think anyone with any kind of power or manual box, dragging theirs, get underneath with a light and check everything that gets stressed, doughnuts first.

Now this has happened the next thing will have to be a prop loop.
If you have a 2 piece prop.....if there is any point fitting a loop at all, there will need to be more than one.

Although fairly sure that most donut setups even if the donut completely fails, the shaft itself still shouldnt be able to drop ?
Yes two. The front one will go eventually anyway, have got a Hardy Spicer already.

Edited by MyM8V8 on Saturday 19th June 17:45

granada203028

1,500 posts

228 months

Saturday 19th June 2010
quotequote all
Normally prop shafts have a pilot bearing inside the doughnuts so it can't separate if the doughnuts complete fails.

In the last weeks of my dear old Granny I lost the 3 sections which are in tension going forward. So I tie wrapped up the remaining three and made a mental note not give it any welly in reverse!

Edited by granada203028 on Saturday 19th June 19:14

monkfish1

12,522 posts

255 months

Monday 21st June 2010
quotequote all
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.

Bonnie and Clyde

11,701 posts

223 months

Monday 21st June 2010
quotequote all
Roger we're due in for a service can you check our doughnuts while we're there?

I'll bring doughnuts

MyM8V8

Original Poster:

9,468 posts

226 months

Monday 21st June 2010
quotequote all
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.
Was it welded to the chassis cross member, or did you bolt it? I think i'm doing this regardless. My knackers are worth more than $99.

MyM8V8

Original Poster:

9,468 posts

226 months

Monday 21st June 2010
quotequote all
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.
My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).

monkfish1

12,522 posts

255 months

Monday 21st June 2010
quotequote all
MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.


Was it welded to the chassis cross member, or did you bolt it? I think i'm doing this regardless. My knackers are worth more than $99.


It was indeed

monkfish1

12,522 posts

255 months

Monday 21st June 2010
quotequote all
MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.


My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).


The stock output shaft will have a hole in it. The spigot is on the prop.

MyM8V8

Original Poster:

9,468 posts

226 months

Tuesday 22nd June 2010
quotequote all
monkfish1 said:
MyM8V8 said:
monkfish1 said:
The prop is located by a spigot into the gearbox tailshaft, so even if the donut is knackered, it "should" stay centred.

We fitted a BMR prop loop on harrys on the forward crossmember.
My new (auto) gearbox output shaft is a super strength 300M version and will have a sliding 1350 yoke. Just in case. (Can't remember seeing any kind of spigot hole in there?).
The stock output shaft will have a hole in it. The spigot is on the prop.
Not in the new one, I'm afraid.