Back from LS Power...
Back from LS Power...
Author
Discussion

djwilk

Original Poster:

1,693 posts

200 months

Wednesday 23rd June 2010
quotequote all
To those who might have been following my other thread.

I think we established the LPG piggyback was the problem in the equasion (as many suggested). So it got disconnected and this is what Mark managed:

For a comparison I put a dyno run from December where the car was bog standard:






I would like to say thank you to Mark (for the great job), Nicola (perfect coffee and good chat) and Dave (for a sarcy but good sense of humour )

I know I will probably start a long thread, but can definitely recommend LS Power to anyone.

cheers
Bart

Boosted LS1

21,200 posts

291 months

Wednesday 23rd June 2010
quotequote all
I'd recommend Mark to although he can be hard to speak to when he's busy.

S800VXR

5,877 posts

231 months

Wednesday 23rd June 2010
quotequote all
Good to hear yrs is sorted. Hopefully Mark will be as forthcoming with the problems I have hanging over from my delivered build.

Magic919

14,595 posts

232 months

Wednesday 23rd June 2010
quotequote all
Good to hear you got the parasite removed.

Well_Fans

4,193 posts

255 months

Wednesday 23rd June 2010
quotequote all
S800VXR said:
Good to hear yrs is sorted. Hopefully Mark will be as forthcoming with the problems I have hanging over from my delivered build.


thought you'd taken your car over to Monkfish, surely if Roger has now worked on the car that would invalidate any warranty you had with Mark?

Certainly that would have been my position when I ran my own IT firm - you get someone else to take apart/modify a pc I supplied while under warranty then that would invalidate it. Maybe if you were a good customer I'd be a bit more flexible but it would depend on what the other firm had done. Only other way I'd honour your warranty would have been if you could provide documentary proof the work had been done using the correct procedures. If the fault was then tracked to something the other firm had done then I'd have issued a bill for labour costs.

In your case, and this is purely a fictional situation - not suggesting it would or even could happen, just using it as a worst case scenario - but imagine Roger decided Mark had got your map wrong and set about changing it. A week later you end up with a hole in a piston - would you expect Roger or Mark to honour any warranty????? They'd both be well within their rights to deny any liability (Mark could blame Roger, Roger could say damage was already done by the "faulty" map)and you'd be left with trying to prove who's fault it actually was. judge

I was surprised when you posted you'd taken the car over to Monkfish so soon after getting it back from Mark - I assumed you must have signed for it "as seen" and had no claim to a warranty or you'd have taken it back to the original supplier ie Mark, especially as he would have had to do any work for free to correct any faults with his work where Roger would surely have to charge you?

Anyway hopefully it wont come to any such nonsense and you'll get a satisfactory outcome if everyone behaves reasonably.

djwilk

Original Poster:

1,693 posts

200 months

Wednesday 23rd June 2010
quotequote all
S800VXR, I saw your car in the workshop the morning it was being dropped off to you on the trailer. Very nice car I am sure they will get to the bottom of it

Tiger_kpt

708 posts

212 months

Wednesday 23rd June 2010
quotequote all
Well_Fans said:

thought you'd taken your car over to Monkfish, surely if Roger has now worked on the car that would invalidate any warranty you had with Mark?


I would have thought this too?!? In that situation, surely Mark would've been your first port of call considering the expense of the build?

To the OP, glad you got your car sorted - looking good. Mine is currently up there as well, you may have seen it - getting a pesky leaking radiator put right and a few other things.

Well_Fans

4,193 posts

255 months

Wednesday 23rd June 2010
quotequote all
Tiger_kpt said:
Well_Fans said:

thought you'd taken your car over to Monkfish, surely if Roger has now worked on the car that would invalidate any warranty you had with Mark?


I would have thought this too?!? In that situation, surely Mark would've been your first port of call considering the expense of the build?

To the OP, glad you got your car sorted - looking good. Mine is currently up there as well, you may have seen it - getting a pesky leaking radiator put right and a few other things.


you going for a new radiatior? get Mark to supply one of the shiny all alloy PWR jobs with the built in oil cooler and power steering rad - he'll enjoy the challenge lol

djwilk

Original Poster:

1,693 posts

200 months

Wednesday 23rd June 2010
quotequote all
Tiger_kpt said:
To the OP, glad you got your car sorted - looking good. Mine is currently up there as well, you may have seen it - getting a pesky leaking radiator put right and a few other things.


I bet I have, just tell me if it was a red Monaro or maybe an ocean blue CV8 or hmmm what else I saw there

doleboy

747 posts

248 months

Wednesday 23rd June 2010
quotequote all
Slightly off topic from the original post (but nothing unusual for us lot) but on the topic of replacement radiators that might facilitate steering & oil coolers but also leave room for an intercooler upfront aswell, who's got what?

Is an OEM replacement plus the secondary coolers the only alternative or is there something cooler (no pun intended) that's less plasticky?

Tiger_kpt

708 posts

212 months

Wednesday 23rd June 2010
quotequote all
djwilk said:
Tiger_kpt said:
To the OP, glad you got your car sorted - looking good. Mine is currently up there as well, you may have seen it - getting a pesky leaking radiator put right and a few other things.


I bet I have, just tell me if it was a red Monaro or maybe an ocean blue CV8 or hmmm what else I saw there


It's a black VXR, black wheels, private plate and orange Wortec body stripes down it.

spudmonkeybikes

1,205 posts

241 months

Wednesday 23rd June 2010
quotequote all
Only go for a pwr if you can get enough air to it, cv8 struggles without modding. Also make sure the eons shroud gets fitted or it will do nothing.

stigmundfreud

22,454 posts

241 months

Wednesday 23rd June 2010
quotequote all
glad its sorted, i was only 912 out on my estimate

spudmonkeybikes

1,205 posts

241 months

Wednesday 23rd June 2010
quotequote all
Mark, does this mean I now get the 2.5k (half my costs, pre the recent issues found) you have been promising me since the end of last year.

S800VXR

5,877 posts

231 months

Wednesday 23rd June 2010
quotequote all
Lots of discussion regarding what I have done with absolutely no knowledge relating to whats happening what so ever! rolleyes

well_fans

4,193 posts

255 months

Wednesday 23rd June 2010
quotequote all
spudmonkeybikes said:
Only go for a pwr if you can get enough air to it, cv8 struggles without modding. Also make sure the eons shroud gets fitted or it will do nothing.


well funnily enough I have the PWR in mine, took a fair bit of work to get it in there but I managed it and with some fairly minor use of a grinder and some aluminium plate arrange everything in such a way as to be able to still install the intercooler on the front of it for a Magnacharger supercharger.

Oh and its an 04 CV8 and I havent had to modify anything to get air to it - even sitting in long queues the temp guage never passes the mid point (where the horizontal bar is as opposed to the angled marks elsewhere round the dial.

PWR is significantly bigger capacity and doesnt suffer from the crappy plastic end tanks on the oem radiator which will just keep failing no matter how many you fit, its a bad design end of. They do two versions - the radiator on its own and the radiator with oil and power steering coolers built in, the latter being significantly more expensive but when you consider you dont get much change out 100 quid with vat and carriage on the replacement oem power steering cooler and thats at monkfish discount price the combined price isnt so bad.

spudmonkeybikes

1,205 posts

241 months

Wednesday 23rd June 2010
quotequote all
Guage only move (if we talking about the dash) after the engine has cooked itself, 170 to 220 and the needle hardly changes position. Scan gauges show the actual temp in degrees F and there is a major difference. My experience though with my setup.

TerryS

1,382 posts

279 months

Wednesday 23rd June 2010
quotequote all
spudmonkeybikes said:
Guage only move (if we talking about the dash) after the engine has cooked itself, 170 to 220 and the needle hardly changes position. Scan gauges show the actual temp in degrees F and there is a major difference. My experience though with my setup.


Regarding your deleted thread, CAPA sold their own Vortech kits using self contained oiling systems. This was possibly the forerunner to Vortech releasing their V3 unit but it did exist and there are lots of guys in Oz running them. I am not surprised the UK dealer knew nothing of this as it is an Oz thing.

HTH

spudmonkeybikes

1,205 posts

241 months

Wednesday 23rd June 2010
quotequote all
I stayed up and called CAPA too and they seemed a little confused about it all.

TerryS

1,382 posts

279 months

Wednesday 23rd June 2010
quotequote all
They shouldn't be they bloody sold them LOL. Seriously, I had to go looking for the info once before, but they do exist, and it was a CAPA only system AFAIK.