ECU Warning light on Gallardo
Discussion
I'm sure this has been done before but the search in PH is somewhat useless these days so can't perform one on just this forum page.
Basically, after getting caught in a heavy (well torrential) shower for the 1st time ever I'm now getting intermittant yellow warning lights on both banks.
So there's me thinking it's something to do with water creeping in somewhere. 1 week later and dried out in the garage and still it's there.
It did go out on two occassions on driving back from France. No apparent power loss. Oil and water temps fine. Oil pressure fine.
Am I right in thinking only option is to go to Lambo and get them read and then diagnosed and reset accordingly?
Car is out of warranty btw.
Cheers,
Chris
Basically, after getting caught in a heavy (well torrential) shower for the 1st time ever I'm now getting intermittant yellow warning lights on both banks.
So there's me thinking it's something to do with water creeping in somewhere. 1 week later and dried out in the garage and still it's there.
It did go out on two occassions on driving back from France. No apparent power loss. Oil and water temps fine. Oil pressure fine.
Am I right in thinking only option is to go to Lambo and get them read and then diagnosed and reset accordingly?
Car is out of warranty btw.
Cheers,
Chris
I had a warning light so bought one of these code readers http://wap.ebay.co.uk/Pages/ViewItem.aspx?aid=3304...
It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
andrew. said:
rusty exhaust particles upset mineThen a few days ago I got simultaneous OBDII checks on both banks. I made Lamborghini Assist get off their lazy idle fat corporate arse and send a man with a code reader; partially in retribution for their shabby cheapskate unhelpful witless idiot performance when I'd had a tyre blow out in the back of beyond a few days prior to that, and mainly to make sure the car was OK to drive round to the workshop. In this case it was a P0506, 'idle air control system RPM lower than expected', and the problem turned out to be that a vacuum pipe had become detached somewhere in the bowels of the engine. Inevitably, though, the dashboard OBDII check indicators all went out within about 500 yards of my setting out to take the car round to the workshop.
If you have a code reader, or a man with a code reader, this turns out to be quite useful:
http://www.lamboweb.com/Repairs_Section/Gallardo_R...
On the rusty particles occasion, Lamborghini Assist sent a man from something called RAC de luxe, or RAC prestige, or something like that. The RAC man's lap-top software did not have Lambo decodes, but it did have Bentley ones which he was adamant would be close enough. The Bentley decodes interpreted the stored fault as a misfire in cylinder 11 which the RAC man was staunchly reluctant to accept was improbable on a Gallardo.
Peter101 said:
I had a warning light so bought one of these code readers http://wap.ebay.co.uk/Pages/ViewItem.aspx?aid=3304...
It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
Was this the exact one you bought, the Autel maxiscan GS500? It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
ChrisFitz said:
Peter101 said:
I had a warning light so bought one of these code readers http://wap.ebay.co.uk/Pages/ViewItem.aspx?aid=3304...
It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
Was this the exact one you bought, the Autel maxiscan GS500? It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
It even has a database of Lamborghini codes.
This one
http://cgi.ebay.co.uk/Autel-Maxiscan-MS509-Car-Dia...
Sorry the previous link of the GS500 is wrong and I didn't notice, although that one may work too, just not the one I ordered.
Edited by Peter101 on Wednesday 14th July 14:41
Peter101 said:
ChrisFitz said:
Peter101 said:
I had a warning light so bought one of these code readers http://wap.ebay.co.uk/Pages/ViewItem.aspx?aid=3304...
It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
Was this the exact one you bought, the Autel maxiscan GS500? It showed the fault was on a heat sensor, with the help of a friend we removed the sensor, cleaned it, replaced it then used the code reader to clear the code. The error light has as of yet not returned.
It even has a database of Lamborghini codes.
This one
http://cgi.ebay.co.uk/Autel-Maxiscan-MS509-Car-Dia...
Hey thanks for that............................................
...............................hope i never have to call you
In the meantime could you.
1 get in your car.
2 turn on and off the ignition 3 times.
3 then lock the doors
4 turn on ignition.
Do you have ecu light still on ?
And no this is not a joke.
...............................hope i never have to call you

In the meantime could you.
1 get in your car.
2 turn on and off the ignition 3 times.
3 then lock the doors
4 turn on ignition.
Do you have ecu light still on ?
And no this is not a joke.
V10 BAT said:
Hey thanks for that............................................
...............................hope i never have to call you
In the meantime could you.
1 get in your car.
2 turn on and off the ignition 3 times.
3 then lock the doors
4 turn on ignition.
Do you have ecu light still on ?
And no this is not a joke.
ok, if my engine goes bang I'm straight round your house mate! lol ...............................hope i never have to call you

In the meantime could you.
1 get in your car.
2 turn on and off the ignition 3 times.
3 then lock the doors
4 turn on ignition.
Do you have ecu light still on ?
And no this is not a joke.

Will give it a go and let you know then.....
Np Will.... Likewise hope none of other need to use it, but for £50 a sound investment I think.
ChrisFitz said:
ok dumb question time...
where is the OBDII cable/socket to plug the reader into?
I thought it was by the fuse box so have looked in here and can't seem to find anything that fits.
help anyone!
It's just below the steering wheel, if you stick your head under you will see it.where is the OBDII cable/socket to plug the reader into?
I thought it was by the fuse box so have looked in here and can't seem to find anything that fits.
help anyone!
Gassing Station | Supercar General | Top of Page | What's New | My Stuff


