Audi A4 B5 CV Joint Replacment
Discussion
Hi all,
Just bought this off ebay http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&am... - it seemed a good price and mine is making a clunking noise, has anyone ever changed a CV Joint on the Audi/VW B5 model? is there anything special I should know??
Just bought this off ebay http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&am... - it seemed a good price and mine is making a clunking noise, has anyone ever changed a CV Joint on the Audi/VW B5 model? is there anything special I should know??
The Riddler said:
Trying to figure what is causing my B5 to 'weave' as well as knock from the nsf.
Did yours seem to drift on mways and stuff too? When B'roading it seems stable, but constant speed on a flat it seems a bit unstable, just had new shockers all around fitted.
Sounds like your track control arms badly need replacing if your getting drift and knocking. Best replace the drop links too when your at it and they all usually go in succession. On the CV joint, when on full lock you will get a bad cracking noise from the front hub on which ever side is gone. Did yours seem to drift on mways and stuff too? When B'roading it seems stable, but constant speed on a flat it seems a bit unstable, just had new shockers all around fitted.
galenthe2nd said:
The Riddler said:
Trying to figure what is causing my B5 to 'weave' as well as knock from the nsf.
Did yours seem to drift on mways and stuff too? When B'roading it seems stable, but constant speed on a flat it seems a bit unstable, just had new shockers all around fitted.
Sounds like your track control arms badly need replacing if your getting drift and knocking. Best replace the drop links too when your at it and they all usually go in succession. On the CV joint, when on full lock you will get a bad cracking noise from the front hub on which ever side is gone. Did yours seem to drift on mways and stuff too? When B'roading it seems stable, but constant speed on a flat it seems a bit unstable, just had new shockers all around fitted.
no weaving or any vagueness in the suspension, but at 90k now and had new suspension at 80k, so my finger would point there if yours is original!
C.V. joint is silent unless im on full lock then i get a slight knocking, im going to attempt it this weekend, so might post some pictures for future reference.
C.V. joint is silent unless im on full lock then i get a slight knocking, im going to attempt it this weekend, so might post some pictures for future reference.
If this helps anyone, heres how I did it...
Time Taken: 3 hours
Special Tools: Modified 17mm Drain Plug Key
Tools Destroyed: 2x 3/8 drivers, 1x 1/2" to 3/8" adaptor
First Remove the Original Audi Nut - This is a 17mm Alan Type Bolt.
Do this with the car on the ground, in Park (or if a manual, with an assistant holding the brakes and the car in gear):

These are the tools I ended up using;
17mm Drain Plug Adaptor, modified to have an 18mm hex on the other end
18mm socket
1/2" to 3/4" adaptor
3/4" Ratchet (would be better with a solid bar, these bolts can be Really tight):

Heres my £16 kit from Ebay, notice the new Bolt had a decent 22mm hex head on, you must replace this bolt and the oil seals:

Once Loose/removed, remove the wheel (jack up the car etc as normal, advisable to lower can onto a good axle stand or large block of wood - Injury your fault, not mine)
Now remove the bolt at the top of the suspension arm:

Drive the bolt out with a suitable tool, ensuring you dont damage the bolt/nut.
KEEP THIS BOLT SAFE!

Now Drive each of the Ball Joints Out, luckily audi have designed this so you dont have to use a fork type splitter, which saves destroying the rubber cover on the ball joint:

Now your suspension should be dangling freely (apart from the bottom link, driveshaft and steering arm...
Now turn the steering so the steering arm is fully extended at the side you are working on:

Now remove the driveshaft from the wheel hub, mine needed some slight persuasion using a plastic screwdriver handle, be careful not to damage the hub (your replacing the CV Joint however!)

Once removed using the ORIGINAL bolt, screw into the cv joing until it is stiff, then Tighten until you feel the CV joint pop off the end of the driveshaft:

now remove the CV joint, oil seals, rubber boot etc (pictures coming soon, i was too greasy to take them at this point!)
Fit the new one on, good luck with this, pictures coming soon...
slide back into the Hub and secure with NEW bolt (hand tighten only at this point)
Fit the top ball joints back in, you may need to jack the hub assembly in and force the link arms down to get them in, i struggled:
Using a Pry-Bar to push the front arm down...


Fitting the new clips onto the rubber boot:

Further Tighten the CV Joint/Hub Bolt, then refit wheel and lower to ground, then Tighten to correct torque (no idea what this is, mine is "reasonably Tight") This bolt clamps your front wheel bearing too, so you must get it correct!!!!
Job Done!
Time Taken: 3 hours
Special Tools: Modified 17mm Drain Plug Key
Tools Destroyed: 2x 3/8 drivers, 1x 1/2" to 3/8" adaptor
First Remove the Original Audi Nut - This is a 17mm Alan Type Bolt.
Do this with the car on the ground, in Park (or if a manual, with an assistant holding the brakes and the car in gear):

These are the tools I ended up using;
17mm Drain Plug Adaptor, modified to have an 18mm hex on the other end
18mm socket
1/2" to 3/4" adaptor
3/4" Ratchet (would be better with a solid bar, these bolts can be Really tight):

Heres my £16 kit from Ebay, notice the new Bolt had a decent 22mm hex head on, you must replace this bolt and the oil seals:

Once Loose/removed, remove the wheel (jack up the car etc as normal, advisable to lower can onto a good axle stand or large block of wood - Injury your fault, not mine)
Now remove the bolt at the top of the suspension arm:

Drive the bolt out with a suitable tool, ensuring you dont damage the bolt/nut.
KEEP THIS BOLT SAFE!

Now Drive each of the Ball Joints Out, luckily audi have designed this so you dont have to use a fork type splitter, which saves destroying the rubber cover on the ball joint:

Now your suspension should be dangling freely (apart from the bottom link, driveshaft and steering arm...
Now turn the steering so the steering arm is fully extended at the side you are working on:

Now remove the driveshaft from the wheel hub, mine needed some slight persuasion using a plastic screwdriver handle, be careful not to damage the hub (your replacing the CV Joint however!)

Once removed using the ORIGINAL bolt, screw into the cv joing until it is stiff, then Tighten until you feel the CV joint pop off the end of the driveshaft:

now remove the CV joint, oil seals, rubber boot etc (pictures coming soon, i was too greasy to take them at this point!)
Fit the new one on, good luck with this, pictures coming soon...
slide back into the Hub and secure with NEW bolt (hand tighten only at this point)
Fit the top ball joints back in, you may need to jack the hub assembly in and force the link arms down to get them in, i struggled:
Using a Pry-Bar to push the front arm down...


Fitting the new clips onto the rubber boot:

Further Tighten the CV Joint/Hub Bolt, then refit wheel and lower to ground, then Tighten to correct torque (no idea what this is, mine is "reasonably Tight") This bolt clamps your front wheel bearing too, so you must get it correct!!!!
Job Done!
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff




