Cost of VR6 rebuild.
Discussion
Why a rebuild? They are pretty strong. They can suffer bore wear sometimes on 1 and 6 and stem seals can go. Timing chain tensioners can wear out leading to rattles and eventual chain failure.
Get the timing chains / tensioners replaced if they are rattly. But if the engine has issues then I'd just replace with a OBDII 2.8 from a breaker golf (you would struggle to notice any difference in power). Used golf vr6s are so cheap its hardly worth rebuilding.
"new" recon basic engine (no ancilliaries) with 2yr warrnaty is less than £3k outright from VW.
Recon engine exchange from VEGE is under £2k
Gearbox IIRC is a VW 02a and any will fit. Best to fit a VR6 donor as the ratios are different - some people like to change the final drive to alter gearing.
There are some very knowledgeable guys on the-corrado.net
Get the timing chains / tensioners replaced if they are rattly. But if the engine has issues then I'd just replace with a OBDII 2.8 from a breaker golf (you would struggle to notice any difference in power). Used golf vr6s are so cheap its hardly worth rebuilding.
"new" recon basic engine (no ancilliaries) with 2yr warrnaty is less than £3k outright from VW.
Recon engine exchange from VEGE is under £2k
Gearbox IIRC is a VW 02a and any will fit. Best to fit a VR6 donor as the ratios are different - some people like to change the final drive to alter gearing.
There are some very knowledgeable guys on the-corrado.net
Edited by was8v on Wednesday 21st July 12:40
Edited by was8v on Wednesday 21st July 12:41
I'm afraid the anser is, how long is a piece of string.
You have to decide how far you are going to go with it. Most engines will benefit masivly from a set of rings and shells, a light hone of the bores and lap the valve seats in, new stem seals + and a new oil pump, and thats it. The problem with VR6 is all the timing chains and guides and tensioners etc are like an extra £500+ on the bill, when on a normal engine you would only be looking a rings shells seals and gaskets ect.
A true rebuild is measuring everthing and replacing/machining everything thats out of spec. If you go down this rebuild route, be aware that when striped you might find it needs the crank grinding, bores honing, head skimming + valve seats recutting, maybe some new valve guides pressing in. Hom much play is there in the litle ends, might need a set of pistons + conrods etc etc and that all adds up pretty quickly.
I would open the yellow pages and call a few local engine rebuilders/engineers and ask for prices. And compare that with the cost of a recon unit from VW.
You have to decide how far you are going to go with it. Most engines will benefit masivly from a set of rings and shells, a light hone of the bores and lap the valve seats in, new stem seals + and a new oil pump, and thats it. The problem with VR6 is all the timing chains and guides and tensioners etc are like an extra £500+ on the bill, when on a normal engine you would only be looking a rings shells seals and gaskets ect.
A true rebuild is measuring everthing and replacing/machining everything thats out of spec. If you go down this rebuild route, be aware that when striped you might find it needs the crank grinding, bores honing, head skimming + valve seats recutting, maybe some new valve guides pressing in. Hom much play is there in the litle ends, might need a set of pistons + conrods etc etc and that all adds up pretty quickly.
I would open the yellow pages and call a few local engine rebuilders/engineers and ask for prices. And compare that with the cost of a recon unit from VW.
Thanks guys,
There is nothing wrong with the engine thats in her.
But just feel if I am going to track her to get her a little stronger.
I am not a tech and don't know loads about engines, but on my Golf GTi 16v I had the following done -(at 120,000)
Shells - Piston rings - head gasket - cam chains - fuel pump and valve stem seals.
I don't want to be at Spa or the 'Ring have have problems.
I know 130,000 miles is not a lot on a V6 lump, but I think its better to be safe then sorry !
I will be going down the road of - new wheel bearing/brakes/brake hose/brake line/engine mounts(upgraded)/de cat ect...
Thanks again for any input you have !
There is nothing wrong with the engine thats in her.
But just feel if I am going to track her to get her a little stronger.
I am not a tech and don't know loads about engines, but on my Golf GTi 16v I had the following done -(at 120,000)
Shells - Piston rings - head gasket - cam chains - fuel pump and valve stem seals.
I don't want to be at Spa or the 'Ring have have problems.
I know 130,000 miles is not a lot on a V6 lump, but I think its better to be safe then sorry !
I will be going down the road of - new wheel bearing/brakes/brake hose/brake line/engine mounts(upgraded)/de cat ect...
Thanks again for any input you have !
Dan7357 said:
But just feel if I am going to track her to get her a little stronger.
I wouldn't worry about this too much. The engine is very robust.I'd recommend an oil cooler for track work as my experience tracking my Corrado VR6 are that the oil can get a bit toasty (I saw 130c before I had the cooler fitted)
As another suggestion, consider just swapping it for a lower mileage engine. I sourced a complete 90k 2.8 VR6 engine last summer for just £265 delivered. A bit of negotiation with my local garage had the engine in the car for around £850, including swapping some bits over and the cost of various gaskets and a new crack pipe.
So in all it cost me £1100, but the engine is a peach and with the go-faster Corrado engine bits swapped over it's just as powerful as the 2.9 engine that preceded it. It also has 50k miles less than the dead engine.
There are ways to "strengthen" a VR6 engine (forged pistons, fancy rods, solid lifters, balancing) but that lot cost you a lot more money than swapping in an R32 engine when you get to it (think : £3k). A set of Wossner forged pistons will set you back almost a grand for example, stronger rods a similar sum, and schrick lifters another couple of hundred.
As the man said, it's a question of how long a piece of string is. If you're going to track it take the advice and fit an oil cooler though, as these engines really do need them for sustained hard track work.
HTH and good luck,
John
So in all it cost me £1100, but the engine is a peach and with the go-faster Corrado engine bits swapped over it's just as powerful as the 2.9 engine that preceded it. It also has 50k miles less than the dead engine.
There are ways to "strengthen" a VR6 engine (forged pistons, fancy rods, solid lifters, balancing) but that lot cost you a lot more money than swapping in an R32 engine when you get to it (think : £3k). A set of Wossner forged pistons will set you back almost a grand for example, stronger rods a similar sum, and schrick lifters another couple of hundred.
As the man said, it's a question of how long a piece of string is. If you're going to track it take the advice and fit an oil cooler though, as these engines really do need them for sustained hard track work.
HTH and good luck,
John
Edited by corozin on Wednesday 21st July 22:18
Iam Keyser Soze said:
If you want drive in drive out Stealth Racing charge around £2700 for a full rebuild.
Vince at Stealth is who did all the engine work on my engine - I've got the dual-tract inlet manifold, Schrick 268 degree cams and steel head gasket. He also did a custom rolling road remap for super-unleaded with a higher rev limit and disabled the factory immobiliser as it was failing and we felt the after-market alarm adequately covered security. Dan7357 said:
was8v said:
If you are looking at dropping thousands on a rebuild then just dropping in a 24v (R32 if you can stretch) is an option - they are a pretty straightforward swap apparently.
gearbox ?edition said:
VR6 gearbox mounts up.......
Yup. 24v with VR6 box with a changed final drive would make a great trackday tool!Engine mounts on 24v and VR6 match (I think you have to modify the front one slightly?) otherwise its just wiring and plumbing (need to relocate battery, eg to spare wheel well to make room for 24v airbox)).
Edited by was8v on Monday 26th July 20:37
did i miss the part where you explain why it needs a rebuild at 130k, i know of quite a few Vr6s that have much higher millage with original HG, Chains etc. We got 175k from a 2.9 before it was smoking and the chains were still fine apart from the top tensioner wearing. A 2.8block can be bought for far less than a 2.9 and you can rebore it to fit your 2.9 pistons into it.
if you are making a track car the best improvements on a VR6 are to change the final drive to a G60 or GTI 16v and get a LSD. Spend the money on those and when/if the engine needs more work then consider the 2.8 4motion/2.8VR6 bottom end swap.
dave
if you are making a track car the best improvements on a VR6 are to change the final drive to a G60 or GTI 16v and get a LSD. Spend the money on those and when/if the engine needs more work then consider the 2.8 4motion/2.8VR6 bottom end swap.
dave
Gassing Station | Audi, Seat, Skoda & VW | Top of Page | What's New | My Stuff


