Fitting new suspension
Discussion
I've bitten the bullet and have ordered a set of Gaz Gold Pros to replace my creaky old Avos. It looks a fairly simple job but does anyone have any useful advice before I start?
Never had a car with coilovers before so how easy is it to set the ride height just using a tape measure? Should i consider getting it checked by a pro in a week or 2 once it's settled down?
I'll be taking the car to a local tyre place in few weeks too to get the geometry setup properly, so I'm hoping for a noticeable difference by the time this is all done!
Cheers
Carl
Never had a car with coilovers before so how easy is it to set the ride height just using a tape measure? Should i consider getting it checked by a pro in a week or 2 once it's settled down?
I'll be taking the car to a local tyre place in few weeks too to get the geometry setup properly, so I'm hoping for a noticeable difference by the time this is all done!
Cheers
Carl
Piece of cake to change, done it on mine. Do one at a time, try to avoid taking the bolts all the way out unless you plan to change them (I didn't but did replace the locking nuts). I found it easier to refit the top first and then the bottom as you can move the lower part of the suspension about easier. If like me you work slowly then each corner shouldn't take more than 40 mins. Measure the height of the car to the centre of each wheel arch from the ground first and match it on the new ones. Set the clicks somewhere in the middle, drive, adjust, repeat until happy.
Got Gaz Gold Pro's on mine now but will admit to having them fitted by APM due to my own time restrictions and he had a look at the geometry too.
Got Gaz Gold Pro's on mine now but will admit to having them fitted by APM due to my own time restrictions and he had a look at the geometry too.
That doesn't sounds too bad then. I've allowed myself a couple of hours so hopefully they'll go on without too much drama and wont take too long to set up. I'm lucky enough to have access to a 4-poster ramp so that should make life pretty easy.
My other half thought I was a bit sad after opening the box tonight and getting excited about some shock absorbers. They do look good though
My other half thought I was a bit sad after opening the box tonight and getting excited about some shock absorbers. They do look good though

The job's a piece of cake, two bolts per spring, job done. I would suggest you think twice before letting tyre monkeys set up the geo though. Firstly they will have no clue what settings to use and secondly no experience of TVR suspension. There must be a local indy or someone the local TVR people can point you to.
When I say local garage I dont mean a nationwide chain of monkeys, its the local indy that my father uses and they have a proper Hunter alignment machine and a good rep. I'll give them a call before I go to check they have the settings for the Chim, but if not it shouldnt be too much trouble to get hold of them!
The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.
The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.
They may have factory settings for your Chim but I would advise you ask the PH collective. Mine is imporoved by not being on factory settings, owners have tweaked and found improvement. There was a thread on here a couple of months ago discussing this and someone posted the preferred road use settings. Worth a quick search
Will do bobfather. Just looked in the Bible and the factory settings are in there, but will also check out other opinions.
It'll probably be 2 weeks before it's adjusted anyway as I'm going to let the new suspension settle down a bit first, then I'll recheck the ride height and take it down to be properly aligned.
Can't wait!
It'll probably be 2 weeks before it's adjusted anyway as I'm going to let the new suspension settle down a bit first, then I'll recheck the ride height and take it down to be properly aligned.
Can't wait!
CarlosV8 said:
W
The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.
APM are near Liphook, if that takes you 90 mins from Scumhampton then you have a problem with your throttle travel too. The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.

Well it's all fitted now, and even without tweaking the settings the car feels so much better! Very pleased with the results, was definitely worth all the expense (and hard work!).
I set the ride height about the same as it was before, but unfortunately the rear has dropped slightly in the way home and I couldnt get the car over the lip into my garage!! Had to fashion a couple of ramps to give me that extra 1cm clearance.
Just gotta find a local garage to set the geometry and sort the ride height.
I set the ride height about the same as it was before, but unfortunately the rear has dropped slightly in the way home and I couldnt get the car over the lip into my garage!! Had to fashion a couple of ramps to give me that extra 1cm clearance.
Just gotta find a local garage to set the geometry and sort the ride height.
.Mark said:
CarlosV8 said:
W
The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.
APM are near Liphook, if that takes you 90 mins from Scumhampton then you have a problem with your throttle travel too. The nearest TVR specialist is 90mins away (unless anyone else knows of one in Southampton area) so it makes it a bit of a PITA to find the time to get there.


Gassing Station | Chimaera | Top of Page | What's New | My Stuff



