ACT smooth bore mod - fitting advice
Discussion
Hi all,
Just bought the ACT smooth bore pipe modification, the kit from the air filter to the plenum. Main reason for buying was the old tumble-dryer waste hose has partially collapsed near the bulkhead from being twisting (heavy handed mechanics by the look of it) and it has holed in the engine bay. Was nearly tempted to go with their trumpet conversion as well but didn't want to get carried away. I understand there is a technique to fitting it, what's the latest advice / experiences - anyone fitted one recently ?
Cheers, Matt
Just bought the ACT smooth bore pipe modification, the kit from the air filter to the plenum. Main reason for buying was the old tumble-dryer waste hose has partially collapsed near the bulkhead from being twisting (heavy handed mechanics by the look of it) and it has holed in the engine bay. Was nearly tempted to go with their trumpet conversion as well but didn't want to get carried away. I understand there is a technique to fitting it, what's the latest advice / experiences - anyone fitted one recently ?
Cheers, Matt
Hiya I fitted the full kit a few months back.
First top tip was from Tim who suggested the method for cutting the pipe. Put the big jubilee clamp around the pipe where you need to cut it and with a brand new stanley blade follow the edge of the clip.........worked a treat.
As for fitting I was told in advance that fitting the nose cone curley pipe from filter to stainless connecter in wheel arch was the hard bit........too right
..............the top bits in the engine bay are simple.
So I chopped elbow to fit Plenum using method above
Heres the bit I found out how to make the job simpler after 5 hours of swearing.......... remove the filter/pipe conector via bolt on top of nose inside bonnet......I relayed this info back to Tim afterwards,
Push short connector tube into long pipe and secure to AFM with about 2" sticking through nose.
Wiggle curly pipe onto it not forgetting to have the jubilee clip on it, push filter bracket pipe into other end then offer retaining bolt to it from above..........you will need to cut it but you can then see how much is needed to come off by proximity of bolt to hole
.........you also have leaway to adjust by sliding the pipes on the tube but it probably will need chopping, mine did.
Good luck with it and the main thing is REMOVE THE BLOODY FILTER BRACKET FIRST
...........I stupidly didn't realise you could.
All the best , it will be straight forward and it DOES make a difference.
Cheers,
Kenny
First top tip was from Tim who suggested the method for cutting the pipe. Put the big jubilee clamp around the pipe where you need to cut it and with a brand new stanley blade follow the edge of the clip.........worked a treat.
As for fitting I was told in advance that fitting the nose cone curley pipe from filter to stainless connecter in wheel arch was the hard bit........too right
..............the top bits in the engine bay are simple.So I chopped elbow to fit Plenum using method above
Heres the bit I found out how to make the job simpler after 5 hours of swearing.......... remove the filter/pipe conector via bolt on top of nose inside bonnet......I relayed this info back to Tim afterwards,
Push short connector tube into long pipe and secure to AFM with about 2" sticking through nose.
Wiggle curly pipe onto it not forgetting to have the jubilee clip on it, push filter bracket pipe into other end then offer retaining bolt to it from above..........you will need to cut it but you can then see how much is needed to come off by proximity of bolt to hole
Good luck with it and the main thing is REMOVE THE BLOODY FILTER BRACKET FIRST
...........I stupidly didn't realise you could.All the best , it will be straight forward and it DOES make a difference.
Cheers,
Kenny
I did it the other way around. Fitted the Air filter and stainless steel tube to the short pipe, all clips done up. Put pipe in place in nose cone with s/s pipe through the bulkhead hole. Use piece of wood to wedge between pipe and nosecone so its firmly stuck in place.
From the engine bag lay up the long pipe, measure and cut. Now stick the front end in some hot water for a minute or two (until soft) . Then push over the s/s connector. Job should be done.
And as per the earlier post only bolt the air filter back down once the jobs done
From the engine bag lay up the long pipe, measure and cut. Now stick the front end in some hot water for a minute or two (until soft) . Then push over the s/s connector. Job should be done.
And as per the earlier post only bolt the air filter back down once the jobs done
Edited by bigdods on Saturday 24th July 09:47
I started doing mine last weekend and found that the hole in the tub behind the headlamp was not big enough for the new pipe to go through. It was only a few minutes with a Dremel to widen it, but by this time the rain had started, knuckles were skinned, and spanners thrown to the floor.
I also struggled with the air filter bracket in the nose but I have an aftermarket alarm siren in the way as well that I'll need to relocate.
I also struggled with the air filter bracket in the nose but I have an aftermarket alarm siren in the way as well that I'll need to relocate.
Thanks chaps, good advice. Looking forwards to getting it now.
Hoping that it will make a difference, although have wondered if it will actually cause a loss in performance as the intake hose is presently holed in several places so air can be drawn in without having to go through the filter, which is presumably easier. Hoping that the several years of driving (probably) with it like that hasn't sandblasted the cylinder bores.
Matt
Hoping that it will make a difference, although have wondered if it will actually cause a loss in performance as the intake hose is presently holed in several places so air can be drawn in without having to go through the filter, which is presumably easier. Hoping that the several years of driving (probably) with it like that hasn't sandblasted the cylinder bores.
Matt
Edited by taylormj4 on Saturday 24th July 23:17
taylormj4 said:
Thanks chaps, good advice. Looking forwards to getting it now.
Hoping that it will make a difference, although have wondered if it will actually cause a loss in performance as the intake hose is presently holed in several places so air can be drawn in without having to go through the filter, which is presumably easier. Hoping that the several years of driving (probably) with it like that hasn't sandblasted the cylinder bores.
Matt
I gained 9bhp at the wheels when I fitted it, but I also had the pre-cats removed so that may have helped too.Hoping that it will make a difference, although have wondered if it will actually cause a loss in performance as the intake hose is presently holed in several places so air can be drawn in without having to go through the filter, which is presumably easier. Hoping that the several years of driving (probably) with it like that hasn't sandblasted the cylinder bores.
Matt
Edited by taylormj4 on Saturday 24th July 23:17
Worth getting a bucket of boiling water and place the ends of the silicone hoses in for a minute prior to fitting to soften them up.
Also clean the mating surface on the plenum and airflow meter with brake cleaner, this will degrease them both and give a 'stickier' surface to mount the hoses to. (They can pop off)
Also clean the mating surface on the plenum and airflow meter with brake cleaner, this will degrease them both and give a 'stickier' surface to mount the hoses to. (They can pop off)
Bomber Denton said:
Worth getting a bucket of boiling water and place the ends of the silicone hoses in for a minute prior to fitting to soften them up.
Also clean the mating surface on the plenum and airflow meter with brake cleaner, this will degrease them both and give a 'stickier' surface to mount the hoses to. (They can pop off)
Thanks Bomber. On ACT's advice, I bought their recommended rubber hose not the blue silicone ones (although I was tempted by the colour). Is brake cleaner Ok with rubber, won't cause them to perish in time ?Also clean the mating surface on the plenum and airflow meter with brake cleaner, this will degrease them both and give a 'stickier' surface to mount the hoses to. (They can pop off)
Matt
taylormj4 said:
Milky400 said:
not sure if you have done it yet, but i remeber removing the indicator, which allowed greater access without cut your hands up!!!
Hi Milky,Not yet, hoping parts will arrive today. How do you remove the indicator ? via the removable hatch in the wheel arch ?
Matt
The toughest part for me when I fitted the mod was having to make the hole in the bulk head larger! I had to widen its circumference considerbaly to get the u-end tube through. After that it was easy fix the pipes (after cutting to correct lengths).
My main advice would be don't cut the long pipe until you have the ubend attached to the filter bracket under the bulkhead and you've attached the two pipes together - this way its a snug fit to the AFM... and secondly once its all tightened up and the Mrs brings you a brew so you admire your handy work together its very helpful to hear her say "shouldn't that silver sleeping bag thingy be on one of those pipes!!"... oh arse I said!
My main advice would be don't cut the long pipe until you have the ubend attached to the filter bracket under the bulkhead and you've attached the two pipes together - this way its a snug fit to the AFM... and secondly once its all tightened up and the Mrs brings you a brew so you admire your handy work together its very helpful to hear her say "shouldn't that silver sleeping bag thingy be on one of those pipes!!"... oh arse I said!

roysum said:
This may help. I to needed to open the hole up a bit but no problem really. I was surprised that there wasn't another short piece of metal tube to connect the filter. The kit relies on using the original bracket and tube which is of smaller diameter.
I've noticed this as well on a dry run fitting, and wondered if I had been sent the incorrect tube, but apparantly this is correct. Does the larger diameter ACT tube tighten up Ok with the hose clips fully tightened on the AFM, plenum and airfilter bracket?I've been meaning to ring AT to check, but it keeps slipping my mind!
the 90 degree bend has one end larger diameter than the other, cannot remember of the top of my head which end goes where, but all tightened up ok.
problem i had was the orignal mounting bracket for the air filter ended up nowhere near where the original was fitted, after a short call Tim he confirmed this was not a problem and all cars varied. A couple of extra holes and a modified mount (2 bits of left over rubber from the pipe) and job done
problem i had was the orignal mounting bracket for the air filter ended up nowhere near where the original was fitted, after a short call Tim he confirmed this was not a problem and all cars varied. A couple of extra holes and a modified mount (2 bits of left over rubber from the pipe) and job done
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




that’s why I am a engineer and not a office jockey 

