Anyone fancy doing a VAG-COM Diagnostic for me?
Anyone fancy doing a VAG-COM Diagnostic for me?
Author
Discussion

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Tuesday 27th July 2010
quotequote all
Beer Tokens included, and i will come to you!

Need my 1999 Audi A4 diagnosing, bought a VAG-Com off ebay but it will only read Engine and Radio, fault is with ABS.

Hoping its not the dreaded pump! frown

00161wj

566 posts

239 months

Tuesday 27th July 2010
quotequote all
Have you changed your brakes recently?

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Tuesday 27th July 2010
quotequote all
ha, no, bought the car, all fine until a couple of weeks later when it started popping up.

I did get the brakes quite hot, well to the point where there smoking and glowing a dull red, just before the error came on.

need to diagnose it then start changing sensors etc!!

Im aware of the possibles and have already wiggled and cleaned all the sensors!!

Matt_N

9,045 posts

233 months

Wednesday 28th July 2010
quotequote all
I bought a cheap ebay code reader for OBDII cars and it brings up the VAGCOM codes which you just read off from the Ross Tech wiki list, cost me £17.99.

TDIfurby

1,997 posts

206 months

Wednesday 28th July 2010
quotequote all
Have vagcom near Exeter if needed. smile

00161wj

566 posts

239 months

Wednesday 28th July 2010
quotequote all
Petrolhead_Rich said:
ha, no, bought the car, all fine until a couple of weeks later when it started popping up.

I did get the brakes quite hot, well to the point where there smoking and glowing a dull red, just before the error came on.

need to diagnose it then start changing sensors etc!!

Im aware of the possibles and have already wiggled and cleaned all the sensors!!
Uusally the fault on these is the abs sensors come slightly lose when people change the brake discs. A good whack with a hammer pushes them back in. But then again could be a sensor which is actually faulty.

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Wednesday 28th July 2010
quotequote all
00161wj said:
Petrolhead_Rich said:
ha, no, bought the car, all fine until a couple of weeks later when it started popping up.

I did get the brakes quite hot, well to the point where there smoking and glowing a dull red, just before the error came on.

need to diagnose it then start changing sensors etc!!

Im aware of the possibles and have already wiggled and cleaned all the sensors!!
Uusally the fault on these is the abs sensors come slightly lose when people change the brake discs. A good whack with a hammer pushes them back in. But then again could be a sensor which is actually faulty.
Yeah, i have reseated them, but it is ok when engine/car is cold, if either the engine or weather is warm it beeps and stays on constantly!


Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Wednesday 28th July 2010
quotequote all
Matt_N said:
I bought a cheap ebay code reader for OBDII cars and it brings up the VAGCOM codes which you just read off from the Ross Tech wiki list, cost me £17.99.
I too got a VAG-COM but it will only read the engine and the radio, nothing else, just says cannot connect! frown

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Wednesday 28th July 2010
quotequote all
TDIfurby said:
Have vagcom near Exeter if needed. smile
Bit out of my way unfortunatly, should have said i live in yorkshire (near york), but travel round sheffield/leeds/york/doncaster area?!

There are beer tokens, surely someone can help??

Thanks TDIFurby, Nice Fabia too beer

TDIfurby

1,997 posts

206 months

Wednesday 28th July 2010
quotequote all
Cheers - The only reason I have vagcom is to keep my own car clean of fault codes and to find out stuff for the hardcore tuning of it. Damn useful tool and mine is fully open so can get into all sections, and run logs and stuff. smile

Matt_N

9,045 posts

233 months

Thursday 29th July 2010
quotequote all
Petrolhead_Rich said:
Matt_N said:
I bought a cheap ebay code reader for OBDII cars and it brings up the VAGCOM codes which you just read off from the Ross Tech wiki list, cost me £17.99.
I too got a VAG-COM but it will only read the engine and the radio, nothing else, just says cannot connect! frown
This is the one I bought:

http://www.amazon.co.uk/Scanner-Reader-SKODA-diagn...

It reads ABS codes.

RS4gareth

5 posts

195 months

Sunday 1st August 2010
quotequote all
Petrolhead_Rich said:
Beer Tokens included, and i will come to you!

Need my 1999 Audi A4 diagnosing, bought a VAG-Com off ebay but it will only read Engine and Radio, fault is with ABS.

Hoping its not the dreaded pump! frown
I have full Vag Com and live near lincoln if thats any good to you or others?

Cheers Gareth

RS4gareth

5 posts

195 months

Sunday 1st August 2010
quotequote all
Petrolhead_Rich said:
Beer Tokens included, and i will come to you!

Need my 1999 Audi A4 diagnosing, bought a VAG-Com off ebay but it will only read Engine and Radio, fault is with ABS.

Hoping its not the dreaded pump! frown
I have full Vag Com and live near lincoln if thats any good to you or others?

Cheers Gareth

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Monday 2nd August 2010
quotequote all
RS4gareth said:
Petrolhead_Rich said:
Beer Tokens included, and i will come to you!

Need my 1999 Audi A4 diagnosing, bought a VAG-Com off ebay but it will only read Engine and Radio, fault is with ABS.

Hoping its not the dreaded pump! frown
I have full Vag Com and live near lincoln if thats any good to you or others?

Cheers Gareth
Thanks alot Gareth, Unfortunately its still a Bit out of my way, but I will keep it in mind in case I'm ever down that way!

Anyone else (Preferably in Yorkshire!)


Defcon5

6,479 posts

222 months

Monday 2nd August 2010
quotequote all
Ive got it, in Castleford. However im off to portugal for 10 days in about 3 hours but if you havent sorted it before I get back ill do it for you.

I work in Leeds, if you are local to there or Cas?

anonymous-user

85 months

Monday 2nd August 2010
quotequote all
Try going into the settings for the USB Cable in control panel -> System -> Device manager. Select the relevant Port (under Ports), right click, properties, Port Settings you should be able to see Latency as an option. If you change this to 5 accessing ABS should now work, if not try latency 4.

Petrolhead_Rich

Original Poster:

4,659 posts

223 months

Tuesday 3rd August 2010
quotequote all
Defcon5 said:
Ive got it, in Castleford. However im off to portugal for 10 days in about 3 hours but if you havent sorted it before I get back ill do it for you.

I work in Leeds, if you are local to there or Cas?
Thanks, Castleford is pretty close to me, I will have a bash at the USB Latency Settings then if it doesnt work I will drop you a PM after your holiday!

biggrin