Vibrations from accelerator pedal on Audi A4 B7 model
Vibrations from accelerator pedal on Audi A4 B7 model
Author
Discussion

vincentlv

Original Poster:

9 posts

195 months

Sunday 1st August 2010
quotequote all
I have a 55 reg A4 B7 2.0 TDI CVT done 73K. A month a ago, I noticed a slight vibration almost feels like a hum in the gas pedal. It is always presenting even at idle, especially can be noticed when the car revo up to 1500rpm , and smooth a while around 2000rpm, then vibrates again from 2500 onwards. I can also feel this kind slight vibrations from the brak pedal and steering wheel. I suspent the vibrations from the engine side . I have had it into the dealer a number of times and they can't find it and now say that they can not feel it. Heck my friend can feel it so I think they are just trying to get out of a repair. Any helps? Thanks

Tame Technician

2,467 posts

235 months

Sunday 1st August 2010
quotequote all
Its an old PD diesel engine, they vibrate alot, ultimately you will feel some of that vibration through the controls.

If you think its pad, ask to test drive an A3 1.9TD, then you'll know what a real vibration is.

If the vibration becomes so badf it feels like a misfire when you rev the engine hard, it could be the flywheel out of balance, but its sounds quite normal to me.

vincentlv

Original Poster:

9 posts

195 months

Sunday 1st August 2010
quotequote all
Hello there, thanks for reply, I was driving A3 and it is quite smooth though. This B7 definiately seems unusual. I had it for more than a year and it was very smooth. Recently just suddently notice this vibration and really annoys me when driving on the motorway. It is CVT transmission. I don think there is a flywheel... Still can not figure out which part can cause this vibation.

Edited by vincentlv on Tuesday 10th August 00:08

Tame Technician

2,467 posts

235 months

Sunday 1st August 2010
quotequote all
There deffinatly is a flywheel, I've changed them.

The CVT box is pretty poor and can be the cause of vibration too, but when they paly up you will know about it the entire car will shake when you pull away.

Your either picking up on somthing begining to fail, or noticing some of the less likable characteristics of that engine/gearbox compination. I was at Audi when B7 were new, I can assure you they do all vibrate, most noticable with the revs raised above idle say 1500 rpm, light finger tip pressure on the steering wheel, slight buzzing.

If thats what you have, its a feature not a fault.

But if its worse than that, will be something rotational at engine speed, so likely causes are flywheel gearbox inputshaft or engine mounts.

vincentlv

Original Poster:

9 posts

195 months

Monday 2nd August 2010
quotequote all
Thanks mate, very useful information. I can definiately say that vibration got on my B7 is worse than the one u mentioned. too much buzzing on the pedals(especially on accelerator pedal). I can not bear that. It does make sense the causes are flywheel gearbox inputshaft or engine mounts. How to carry out the investigation on unputshaft or the engine mount? I been to lots of garages they all said the engine mounts are fine. Unfortunately, no faults have been found out by them. But they indeed realize the vibartion which are not usual. I ve been lots of places trying to target the fault but none. May i ask if you still working in mechanical side? Is it convinient to help me have a investiagtion on my B7 as i can see u r very much professional on this tricky problem. That would be very greatful.Thanks mate, much appreciate.

Edited by vincentlv on Tuesday 10th August 00:09

vincentlv

Original Poster:

9 posts

195 months

Friday 6th August 2010
quotequote all
Hello mate, I ve been to garage again, they took the belt and pully off when the car is warm, but still doing the vibrations. Also,they tried to check out if the wirings of injectiors are fine, open the oil cover and found out them four are good. Really dont know what to check. Do you still think that would be the engine mounts? But they are the electronic ones. If they are faulty, there should be some warning lights on. Btw, how to check out of the flywheel inputshaft? Thanks.


Edited by vincentlv on Tuesday 10th August 00:10

Tame Technician

2,467 posts

235 months

Saturday 7th August 2010
quotequote all
If the engine mounts are electronically faulty, it logs a code, but it wont put the warning light on as there is no effect on emmisions.

But mechanical failure of engine mounts can happen also, they loose there hydralic fluid and become less effective at damping vibration. You can normally see it leaking or see a stain where it has leaked out. Replace and retry.


There is no way to accuratly check the flywheel, its also a replace and see if there is any improvement type of thing. That said with the gearbox removed, you can measure the movement of the flywheel, but generally even brand new ones feel really floppy with loads more side to side in them than you would think.

Absolutely no way to check input shaft either.

Flywheel is about £500 + £350 for fitting.

Input shaft maybe £1500 ish. But it could be an internal gearbox fault causeing it to vibrate.

As I said, they do vibrate, I really would try and live with it. You wouldnt want to spend £2000 and it be exactly the same.


vincentlv

Original Poster:

9 posts

195 months

Tuesday 10th August 2010
quotequote all
I would try to get used to it, but it is getting worse now. Do you have any ideas on DIY gas pedal? I would think if it is possible cover an antivibration pad on the accelerator pedal or some antivibration washers beneath the screws? I think this will reduce the grinding feeling. Is that possible? Thanks

ecain63

10,653 posts

206 months

Tuesday 10th August 2010
quotequote all
Just like on the A6 the A4 has a rubber bush where the pedal meets the bulkhead. On the A6, any vibration through the pedal is a sign that the bush is getting worn. If you have an S-Line then the vibration will be worse due to its harder suspension. I'd be looking somewhere in that direction.

vincentlv

Original Poster:

9 posts

195 months

Tuesday 10th August 2010
quotequote all
ecain63 said:
Just like on the A6 the A4 has a rubber bush where the pedal meets the bulkhead. On the A6, any vibration through the pedal is a sign that the bush is getting worn. If you have an S-Line then the vibration will be worse due to its harder suspension. I'd be looking somewhere in that direction.
Thanks mate, will this rubber bush also cuase steering wheel vibration? I will check out this rubber~ Thanks mate

ecain63

10,653 posts

206 months

Tuesday 10th August 2010
quotequote all
vincentlv said:
ecain63 said:
Just like on the A6 the A4 has a rubber bush where the pedal meets the bulkhead. On the A6, any vibration through the pedal is a sign that the bush is getting worn. If you have an S-Line then the vibration will be worse due to its harder suspension. I'd be looking somewhere in that direction.
Thanks mate, will this rubber bush also cuase steering wheel vibration? I will check out this rubber~ Thanks mate
I dont think it would affect the steering wheel vibration, but with that info i'd be looking at the suspension / wishbones / arms as this would affect both the steering column and the pedals.

vincentlv

Original Poster:

9 posts

195 months

Tuesday 10th August 2010
quotequote all
I dont think it would affect the steering wheel vibration, but with that info i'd be looking at the suspension / wishbones / arms as this would affect both the steering column and the pedals.
[/quote]

Even the car is idle? The suspension wishbones/ arms would give out vibrations? Thanks


vincentlv

Original Poster:

9 posts

195 months

Monday 16th August 2010
quotequote all
Tame Technician said:
If the engine mounts are electronically faulty, it logs a code, but it wont put the warning light on as there is no effect on emmisions.

But mechanical failure of engine mounts can happen also, they loose there hydralic fluid and become less effective at damping vibration. You can normally see it leaking or see a stain where it has leaked out. Replace and retry.


There is no way to accuratly check the flywheel, its also a replace and see if there is any improvement type of thing. That said with the gearbox removed, you can measure the movement of the flywheel, but generally even brand new ones feel really floppy with loads more side to side in them than you would think.

Absolutely no way to check input shaft either.

Flywheel is about £500 + £350 for fitting.

Input shaft maybe £1500 ish. But it could be an internal gearbox fault causeing it to vibrate.

As I said, they do vibrate, I really would try and live with it. You wouldnt want to spend £2000 and it be exactly the same.
hello Tame, I been to garage today. They found out a problem but not sure if it is this problem causing the vibration. Right, they found out the cambelt bearing is degreasing, and making noise, it is leaking a bit. The cambelt is due to change in 2000 miles. Do you think that is the problem causing the vibrations?

Thanks


Tame Technician

2,467 posts

235 months

Monday 16th August 2010
quotequote all
vincentlv said:
hello Tame, I been to garage today. They found out a problem but not sure if it is this problem causing the vibration. Right, they found out the cambelt bearing is degreasing, and making noise, it is leaking a bit. The cambelt is due to change in 2000 miles. Do you think that is the problem causing the vibrations?

Thanks
Not sure what they mean by degreasing, or which bearing they are refering too. There is a tensioner, and two rollers on the 2.0 TDI. All would be replaced if the cam belt is replaced using the correct full kit.

Cant see that causing a vibration though, unless the tensioner has slackened off and allowed the valve timing to get out of spec, very unlikely.

There is a litle alarm bell ringing in my head now, you said its making a noise, are they 100% sure that noise is coming from the cam belt tensioner/idlers. Have the used a stetherscope or even screw driver to the ear etc.

IT is a BLB engine?????

I ask the question because the begining of the oil pump chain tensioner failure is a kind of rotational scraping sould from the front of the engine, easily mistaken for aux drive noise, such as alternator bearing or A/C compressor. (I know you said than ran the engine with the Aux belt off, so they must of thought it was in that area)

Oil pump chain also drives the counter balance shafts, a slack chain could mean the shafts running slightly out of time and that could give you the vibration.

Only way to know would be to drop the sump for inspection (a big job) so I wouldnt do so unless they pretty sure there is somthing wrong in there. Just from your description there is no way to know, so dont panic just yet.

Have you tried taking the car to an Audi centre, any dealer master tech would recognise the sound if its that, or at least say, "sounds like the A/C compressor, we'd have to try it with the Aux belt off" which you know has already been done.

This is what I mean, here is one, that the customer didnt hear and the chain snaped, which is bad.
http://www.audi-sport.net/vb/showthread.php?t=8199...

IF its as BRE engine, they dont have the chain, but a set of gears instead, these can wear and cause a similar mistiming of the balancer shafts, but is very rare indeed, unlike the chain issue which, well isnt.