Discussion
I bought all the parts & fully intended to remove the cats myself.
To do it properly I wanted to remove the manifolds, I had a small blow from one side that was getting on my nerves & helped me justify the job.
However it looked like a pain in the A to do on the drive (wish I still had my ramp) so in the end I paid Perry Mott £300 to do it for me.
Perry removed both manifolds, cut them open and extracted the cats, the manifolds were then nicely re-welded on his jig.
The manifolds were re-fitted using the correct large port metal composite gaskets, Nordlock washers and stainless ARP bolts.
He did a nice job and sorted a missing bolt from an engine mount and a few other bits & bobs all within the price.
With the best quality gaskets & fasteners used the manifolds are now properly sealed for good and the blowing when cold is solved.
The sound is a bit deeper, more Tom Jones & less Aled Jones.
Performance wise, I must admit I didn't notice much if any difference.
I am happy to recommend Perry based on the very thorough job he did for me.
Considering the time involved and the extra bits he did for me I think £300 is a fair price.
Hope this answers your questions?
To do it properly I wanted to remove the manifolds, I had a small blow from one side that was getting on my nerves & helped me justify the job.
However it looked like a pain in the A to do on the drive (wish I still had my ramp) so in the end I paid Perry Mott £300 to do it for me.
Perry removed both manifolds, cut them open and extracted the cats, the manifolds were then nicely re-welded on his jig.
The manifolds were re-fitted using the correct large port metal composite gaskets, Nordlock washers and stainless ARP bolts.
He did a nice job and sorted a missing bolt from an engine mount and a few other bits & bobs all within the price.
With the best quality gaskets & fasteners used the manifolds are now properly sealed for good and the blowing when cold is solved.
The sound is a bit deeper, more Tom Jones & less Aled Jones.
Performance wise, I must admit I didn't notice much if any difference.
I am happy to recommend Perry based on the very thorough job he did for me.
Considering the time involved and the extra bits he did for me I think £300 is a fair price.
Hope this answers your questions?
I had mine done at Topcats, probably around the same price but as it was one of a number of jobs I cant tell you exactly. They do it the same way though, cut open the manifold, remove pre-cats then weld it back up again.
You can DIY it without the cut and re-weld using long screwdrivers, files etc but I understand its a long and filthy job.
THis is for the pre-cats only, if you want to remove the main cat too you really need to replace the dustbin with an ACT jobby.
ETA: didnt notice any more noise, but then I am already sleeved .....
I gained 9bhp at the wheels after having the pre-cats removed and fitting the ACT induction pipe. As they were done together I cant say if the pre-cats actually caused any power gain, but I understand that no power gain is normally made.
The only reason I had them removed is that the manifolds were off anyway and as pre-cats are a known weak point it made sense to get rid of them now rather than wait for them to fail.
You can DIY it without the cut and re-weld using long screwdrivers, files etc but I understand its a long and filthy job.
THis is for the pre-cats only, if you want to remove the main cat too you really need to replace the dustbin with an ACT jobby.
ETA: didnt notice any more noise, but then I am already sleeved .....
I gained 9bhp at the wheels after having the pre-cats removed and fitting the ACT induction pipe. As they were done together I cant say if the pre-cats actually caused any power gain, but I understand that no power gain is normally made.
The only reason I had them removed is that the manifolds were off anyway and as pre-cats are a known weak point it made sense to get rid of them now rather than wait for them to fail.
Edited by bigdods on Wednesday 4th August 15:49
mac123yre said:
spoke to steve heath about this he recons you loose power doing this
The majority who have had this done would tell you otherwise,even if the drop was very minimal you cant tell,the point is it releases less restriction and seems to let the engine rev easier.When done with the induction system and flared trumpets from ACT and the spacer and gasket from SC POWER,the results will be significant.

Gassing Station | Chimaera | Top of Page | What's New | My Stuff





tard. Once the manifolds are off, you can remove the precats using a long masonary bit and various sized chisels. Mine took approx 1 to 2 hours each manifold.