Rear number plate - MOT failure
Rear number plate - MOT failure
Author
Discussion

King Fisher

Original Poster:

739 posts

210 months

Wednesday 4th August 2010
quotequote all
My Chimaera failed its MOT today because the rear number plate is not illuminated (the plate sits flush with the rear bodywork with the lights behind it) - the tester said I had to get a smaller recessed plate fitted.

Every Chimaera I've ever seen has a number plate like mine and it was like this whan I bought it. How else can I get round this, as recessed plates look awful?

Thanks for any advice.

More Steam

698 posts

221 months

Wednesday 4th August 2010
quotequote all
If it's a pre-facelift Chim, it'll need a backlit plate. It may very well have this already, but it's hard to make it out in daylight. I always inform the tester prior to testing, as it's very unusual. Plates are available from http://www.craigsplates.com/. They have a section especially for TVR rear plates.

HTH


Meatball

1,638 posts

241 months

Wednesday 4th August 2010
quotequote all
Or get it moted at a TVR friendly place.

phillpot

17,525 posts

214 months

Wednesday 4th August 2010
quotequote all
Sounds bonkers to me !

providing you have the correct type of plate (light can shine through it)shouldn't be a problem, hundreds of us get through MOT's each year with this standard, factory fitted set up.

Sure someone with more knowledge/experience will be along soon to tell you how to appeal ?

I find it really is worth trying to find a "TVR friendly" garage for MOT's if possible

fat tony

392 posts

238 months

Wednesday 4th August 2010
quotequote all
Mine failed on this too. Ive never had a problem before. I think its down to the tester and if its a TVR friendly place.

M@H

11,298 posts

303 months

Wednesday 4th August 2010
quotequote all
I have found it helps if they can see that the lights are on so its worth showing the back of the lights to the tester with the boot open.

Cheers,
Matt

rigga

8,808 posts

232 months

Wednesday 4th August 2010
quotequote all
Be aware also that a lot of testers are now failing honeycombed plates that tivs need in order to allow tge backlit light through ...... this legislation though only aplies to post 2001 cars so if your car is pre this date and they fail it on a translucent rear number plate do not accept it.

spinbo

28 posts

207 months

Wednesday 4th August 2010
quotequote all

King Fisher

Original Poster:

739 posts

210 months

Wednesday 4th August 2010
quotequote all
Thanks to all who replied.

My car is a 1998 model and has a translucent rear plate. Clearly, I will now be able to sort this out. It was the only thing it failed on!

spinbo

28 posts

207 months

Wednesday 4th August 2010
quotequote all
Tried to link to the specific pages but it just brings up the whole manual.
Have a look through,it clearly says that backlit number plates are acceptable (obviously have to be opaque) and the failure for honeycombe plates only applies after 1st september 2001.
Chances are the tester has never come across it but should have checked,sure if you guide him in the right direction you will get a pass!

BliarOut

72,863 posts

270 months

Wednesday 4th August 2010
quotequote all
Yup, he was wrong to fail you. Show him the lights working from the inside, I always have a laugh about it with my local tester biggrin

The conversation usually goes something like "But I can't see them". "Nope, you won't, it's a TVR, that's how they are"

edward1

839 posts

297 months

Thursday 5th August 2010
quotequote all
As Blairout said, show them the lights are on behind the plate and explain that in daylight you won't see them. As long as you have the correct honeycomb plate fitted you shouldn't have a problem. Use a friendly MOT station or one that knows TVR's

finestjammy

741 posts

204 months

Thursday 5th August 2010
quotequote all
Mine failed the MOT on the number plate issue. I swapped to one made by these guys: http://www.pistonheads.com/gassing/topic.asp?h=0&a... and it passed the second time.