Clutch replacement...
Clutch replacement...
Author
Discussion

Bassfiend

Original Poster:

5,530 posts

281 months

Sunday 8th August 2010
quotequote all
My clutch is slipping under hard acceleration in 2nd and 3rd so looks like it's well on the way out ... has anyone replaced their own? (and if so - is it a pig to do? I have access to a pit.) Any recommendations where to get a standard clutch for a 400HC? (Don't see any point in anything "uprated" as I'm not going to be doing any engine work on it.)

Alternatively - anyone got any recommendations for anywhere in the Salisbury (Wiltshire / Dorset) area that would be worth contacting to do the job? How much can I expect to pay?

(I did try searching but it's under maintenance.)

Cheers

Phil

ButtonIt

385 posts

209 months

Monday 9th August 2010
quotequote all
Two quotes I had were both around the £750 mark from TVR specialists. I sourced the parts myself and got a friendly local mechanic to do it for £200, although we did have a few problems (faulty parts supplied) which meant my poor mechanic had to do the job twice. It's not that difficult by all accounts.

V8NRG

854 posts

274 months

Monday 9th August 2010
quotequote all
Copied from another thread :

I did the clutch on a 400 myself, parts cost about £300.
That included friction and pressure plates, bearing and carrier, fork, pivot point pushrod and retaining clip, new gearbox oil, grease etc.

Check the history on my 400 for part numbers / prices and where I got them from.

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
I'm assuming it's just a case of dropping the propshaft and box rather than having to faff about unbolting the engine mountings and pulling the engine forward? Yes?

Have a pit in my garage so that would hopefully make life easier...

Phil

V8NRG

854 posts

274 months

Monday 9th August 2010
quotequote all
Put car on axel stands, over a pit or whatever to get access.
Remove Exhaust,
Drain gearbox oil,
Remove Prop shaft,
Undo remote gear linkage(from inside),
Remove gearbox,
Remove Bell housing,
Remove clutch plates.

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
Ta! Sounds like a pleasant day out... wink

Suppose I should do the gearbox oil as well - damn - hadn't thought about that ... hateful smelly stuff as far as I remember... frown

Phil

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
Can you do the rear engine oil seal whilst it's all out (obviously youd need to take the flywheel off also).. but may be worth it??
driving

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
TVR Beaver said:
Can you do the rear engine oil seal whilst it's all out (obviously youd need to take the flywheel off also).. but may be worth it??
driving
Are they prone to failing?

Might get a seal in case we spot a leak whilst it's out but would rather not start disturbing too much unless there's good reason. wink

Phil

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
No.. never go... until 5 miles after you've put it all back together laugh
they can become hard with age and miles.... do you ever get drips from your bell housing??... If it was me, I'd do it... but just check you can get to it first without lowering the sump or something... but if you can????? your choice.. yes

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
TVR Beaver said:
do you ever get drips from your bell housing??
rofl

...it's one of those immature days today.

Phil

Barreti

6,689 posts

268 months

Monday 9th August 2010
quotequote all
Dare I ask, and possibly make myself look really stupid here, but why do you need to drain the oil out of the gearbox to change the clutch?

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
So when you pull the prop shaft out you don't get a gob full I assume.... vomit

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
TVR Beaver said:
So when you pull the prop shaft out you don't get a gob full I assume.... vomit
Gearbox oil is hateful stuff - got some in my hair when I was young (and still had hair) and the bloody stuff would not come out. frown

I'm assuming that the advice to drain is so it doesn't gloop out too...

Phil

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
nearly as bad as Siphoning diesel and drinking a bit!!.. you cant tast it for days after... yuck.. hurl

Barreti

6,689 posts

268 months

Monday 9th August 2010
quotequote all
Wouldn't you just unbolt the prop though?

boxedin
I just knew I was going to make myself look stupid here

Edited by Barreti on Monday 9th August 17:33

TJC46

2,199 posts

237 months

Monday 9th August 2010
quotequote all
You unbolt the prop from the diff, but at the gearbox end its just a push fit onto a splined shaft. Many make the mistake [including myself] of unbolting at the diff, sliding the prop rearwards out of the gearbox and a small amount of oil comes out. You think to yourself, thats not too bad, only later when you unbolt everything and your lay on your back under the car, and you slide the gearbox away from the engine, and tilt the back end down slightly,hehe you get the entire contents of the gearbox all over yourself. Not recommended.

neal1980

2,585 posts

270 months

Monday 9th August 2010
quotequote all
TJC46 said:
and you slide the gearbox away from the engine, and tilt the back end down slightly,hehe you get the entire contents of the gearbox all over yourself. Not recommended.
I can confirm this is VERY TRUE..lol biglaugh

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
Anyone know David Batty's email address? The one I have for him (david@thegarage54.fsnet.co.uk) is bouncing...

(Thought I'd give him a try as he's near my mates house so easy to get to.)

Phil

Kitchski

6,552 posts

262 months

Monday 9th August 2010
quotequote all
I bought an AP clutch from V8 developments, £150 delivered. I also bought the uprated arm, pivot and new master cylinder to keep it all sweet.

William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!

Total cost for new, fitted clutch £300. Jobbed!

Bassfiend

Original Poster:

5,530 posts

281 months

Monday 9th August 2010
quotequote all
Kitchski said:
I bought an AP clutch from V8 developments, £150 delivered. I also bought the uprated arm, pivot and new master cylinder to keep it all sweet.

William Street Services in Southampton charged £150 pure labour (with reciept) to install it, as I didn't fancy that one on the driveway!

Total cost for new, fitted clutch £300. Jobbed!
Dropped them an email - let's se if they're up for doing another... wink

Phil