Lost my splitter
Lost my splitter
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Monday 9th August 2010
quotequote all
I lost my splitter over the weekend (it came off and hit a caravan yikes)
There was some alternative diy options on here a little while back has anyone got a link or any information i dont fancy shelling out another £50 for a new one.
Cheers

sapper

1,134 posts

236 months

Monday 9th August 2010
quotequote all
TVR car parts have got a replacement for £30, not cheap but less than £50

BliarOut

72,863 posts

270 months

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
http://cgi.ebay.co.uk/TVR-Griffith-Chimaera-Splitt...

These are very good units..(or so I'm told!). driving

M@H

11,298 posts

303 months

Monday 9th August 2010
quotequote all
TVR Beaver said:
...(or so I'm told!). driving
..of course. wink

and are they available off ebay also? angel

Cheers,
Matt

C3BER

4,714 posts

254 months

Monday 9th August 2010
quotequote all
TVR Beaver said:
http://cgi.ebay.co.uk/TVR-Griffith-Chimaera-Splitt...

These are very good units..(or so I'm told!). driving
Can you do cerb ?

TVR Beaver

2,874 posts

211 months

Monday 9th August 2010
quotequote all
I think they are indeed... try barrans.j@heights-uk.com and I'll pass the message on wink

how does a Cerby one differ?.. any dim's etc?? driving

Golflion

2,782 posts

252 months

Monday 9th August 2010
quotequote all
Meatball said:
I lost my splitter over the weekend (it came off and hit a caravan yikes)
There was some alternative diy options on here a little while back has anyone got a link or any information i dont fancy shelling out another £50 for a new one.
Cheers
Just use plastic gutter,use the half round section type and cut in half,secure with screws but bed on Sikaflex silicone,very flexible when going over speed bumps etc unlike the ridgid aluminium.
idea

nikman

878 posts

236 months

Thursday 19th August 2010
quotequote all
I always argued for the necessity of the splitter and had long discussions right here about the correct way they should face, location on the valance and of course the undoubted benefits... high speed stability improvements, preventing the n/s trailing edge of bonnets lfting on cars so affected and of course, engine cooling.

But when mine came off for the thrid time (in nearly 3 years) on a mound in the grass at Chatsworth, I decided to fill the holes and leave it off for a bit.

Conclusion is that unless you are track 'daying' or very frequently seeing triple digit speeds come up in front of you, the annoyance outweighs any benefits. I'd caught mine on innocent looking country lanes, turning into relatively level looking suburban side roads, and driveways etc.

9k miles later I'm no longer pussyfooting around on anything that doesn't look billiard table flat and have not touched any part of the uinderside of my car on anything at all. I'm not recommending removing or leaving off the splitter but wouldn't say it's as vital as some think.

Nick.

Don1

16,887 posts

239 months

Thursday 19th August 2010
quotequote all
Meatball said:
it came off and hit a caravan
Good shot!

TVR Beaver

2,874 posts

211 months

Thursday 19th August 2010
quotequote all
nikman said:
I always argued for the necessity of the splitter and had long discussions right here about the correct way they should face, location on the valance and of course the undoubted benefits... high speed stability improvements, preventing the n/s trailing edge of bonnets lfting on cars so affected and of course, engine cooling.

But when mine came off for the thrid time (in nearly 3 years) on a mound in the grass at Chatsworth, I decided to fill the holes and leave it off for a bit.

Conclusion is that unless you are track 'daying' or very frequently seeing triple digit speeds come up in front of you, the annoyance outweighs any benefits. I'd caught mine on innocent looking country lanes, turning into relatively level looking suburban side roads, and driveways etc.

9k miles later I'm no longer pussyfooting around on anything that doesn't look billiard table flat and have not touched any part of the uinderside of my car on anything at all. I'm not recommending removing or leaving off the splitter but wouldn't say it's as vital as some think.

Nick.
Nick.. that is strange as I've run with.. and without.. and it makes a big difo.... also going to work, I run over 3 full speed humps and about 6 sets of thoes small mound type humps.. and yes, I have to slow down.. but I've never hit it at all.. even going into my Mums drive thats about 30 deg off the road, I have no issue... What size of splitter have you been fitting? The ones I have sit's down just under 30mm but I am on the orig Billy's.. may be if you lower your car on other shocks you'd have more of an issue?? driving




nikman

878 posts

236 months

Friday 20th August 2010
quotequote all
TVR Beaver said:
nikman said:
I always argued for the necessity of the splitter and had long discussions right here about the correct way they should face, location on the valance and of course the undoubted benefits... high speed stability improvements, preventing the n/s trailing edge of bonnets lfting on cars so affected and of course, engine cooling.

But when mine came off for the thrid time (in nearly 3 years) on a mound in the grass at Chatsworth, I decided to fill the holes and leave it off for a bit.

Conclusion is that unless you are track 'daying' or very frequently seeing triple digit speeds come up in front of you, the annoyance outweighs any benefits. I'd caught mine on innocent looking country lanes, turning into relatively level looking suburban side roads, and driveways etc.

9k miles later I'm no longer pussyfooting around on anything that doesn't look billiard table flat and have not touched any part of the uinderside of my car on anything at all. I'm not recommending removing or leaving off the splitter but wouldn't say it's as vital as some think.

Nick.
Nick.. that is strange as I've run with.. and without.. and it makes a big difo.... also going to work, I run over 3 full speed humps and about 6 sets of thoes small mound type humps.. and yes, I have to slow down.. but I've never hit it at all.. even going into my Mums drive thats about 30 deg off the road, I have no issue... What size of splitter have you been fitting? The ones I have sit's down just under 30mm but I am on the orig Billy's.. may be if you lower your car on other shocks you'd have more of an issue?? driving



Yes, there certainly is A difference as I discovered one windy day at, errm, well didn't really notice how fast exactly as I was puzzling over why I'd almost changed lanes without really intending to!!

This is very strange because my splitter sits down closer to 20mm than your 30 and I too am on the orig shocks. I measured the ride height against a friends Chim also on original shocks and found my car to be about 10mm lower (taking different tyre profiles into account etc). Maybe it was this that made the difference.

I really am aware of what I'm driving over yet 'banged' it on the road more times than I can remember. Usually it would be one corner or the other. I'm not talking about speed humps etc here!! I can even remember hitting in on the tarmac connecting a petrol station forecourt with the public road outside!!

If/when I change shocks I will probably try again with a higher ride height because I agree there is A difference - just not enough for me right now to warrant the hassle.

S4CJO

429 posts

290 months

Friday 20th August 2010
quotequote all
Try Ian @ sportmotive Stoke

hiltonig

3,153 posts

239 months

Friday 20th August 2010
quotequote all

TVR Beaver

2,874 posts

211 months

Saturday 21st August 2010
quotequote all

SILICONE KID

14,997 posts

262 months

Saturday 21st August 2010
quotequote all
Does anyone have any pics for the correct position.

TJC46

2,199 posts

237 months

Saturday 21st August 2010
quotequote all
Forward facing is the correct way. You are trying to create pressure behind it which helps cooling.
TJC46 said:
Thanks for all the input, this topic started a somewhat interesting discussion. Anyway ive fitted it now. It will or wont have any aerodynamic effects, it will or wont have any cooling effects, im pretty sure it will stop bonnet lift at higher speeds, and im definetly sure it will work as a mini snow plough, if it snows again. hehe

BliarOut

72,863 posts

270 months

Saturday 21st August 2010
quotequote all
You're actually trying to create a low pressure area wink

TJC46

2,199 posts

237 months

Saturday 21st August 2010
quotequote all
BliarOut said:
You're actually trying to create a low pressure area wink
Thats what i was tryin to say

BliarOut

72,863 posts

270 months

Saturday 21st August 2010
quotequote all
thumbup when you get it right it evacuates the underbonnet very effectively biggrin