Misfiring
Author
Discussion

.Mark

Original Poster:

11,104 posts

307 months

Wednesday 11th August 2010
quotequote all
Noticed a misfire coming home yesterday when at the high end of the rev range, will be going out to check leads etc later, but, as it was running well at normal speeds I'm not sure I'll find anything.

Could it be the coil breaking down perhaps, or some other electrical trickery happening? It wasn't as bad, but resembled hitting the rev limiter but came on about 4k revs or so.

Don

28,378 posts

315 months

Wednesday 11th August 2010
quotequote all
Check the HT leads - particularly the ones closest to the bulkhead nearest to the driver. (RHD)

On our Chim those leads get hot and then become loose. The first indication they've come loose is misfiring under strong acceleration - as the g-force dislodges the lead from the plug!

On our holiday this year I got bad misfiring on the motorway within minutes of leaving home. One services stop later accompanied with much pushing on of leads and burning of fingers it was good to go for the rest of the fortnight!

P.S. If you can wait until it's cold you will swear less. biggrin

.Mark

Original Poster:

11,104 posts

307 months

Wednesday 11th August 2010
quotequote all
Cheers Don, will get out there later, it'll be cold alright, drove straight in the garage and left it there. Bit like a primadonna F1 driver quitting a race hehe

big geoff

387 posts

231 months

Wednesday 11th August 2010
quotequote all
Remove all 8 heat shields then road test before you look further

jvr

789 posts

278 months

Wednesday 11th August 2010
quotequote all
I had same problem,HT lead was loose,not even connected but was missing at any revs under any loads but still drove and idled ok,however when i was at the ring before all of this the car was missing under load seemed to be down on power a bit,about 4000 rpm upwards.When I got home i changed the coil as it seemed it was the original one and all seems ok now and is lot more eager to rev to 6000rpm than it used to.
Try the coil after the leads its a cheap part.
P

.Mark

Original Poster:

11,104 posts

307 months

Wednesday 11th August 2010
quotequote all
Plug leads seem ok but didn't have time to check the rest of the HT stuff, ran it in the garage and it revved through the range well enough so perhaps just an iffy connection at the plug end.

One this did worry me though, I only revved it for a few moments after letting it idle for a bit but should the manifolds glow? Appreciate they get hot quick and there was no air flow over them but glowing? I've heard that's a sign of blocked cats? Both sides were glowing too.

M@H

11,298 posts

303 months

Wednesday 11th August 2010
quotequote all
I assume you had the leads off.. in this scenario it would suggest to me that you have a couple the wrong way round - I'd double check that first smile (although usually it would just be glowing on one side if its just a couple)

Edited by M@H on Wednesday 11th August 18:49

.Mark

Original Poster:

11,104 posts

307 months

Wednesday 11th August 2010
quotequote all
Did refit the leads but one at a time (Been caught out before!) so they are all in the correct place.

M@H

11,298 posts

303 months

Wednesday 11th August 2010
quotequote all
Hmmm... shouldn't really be glowing then.. as you say, the next option could well be a blockage.. the only other thing that springs to mind is timing but that would have to be pretty well out!

.Mark

Original Poster:

11,104 posts

307 months

Wednesday 11th August 2010
quotequote all
Yes indeed, but at low revs, slow speed it behaves perfectly. Odd, will give APM a call tomorrow.

ButtonIt

385 posts

209 months

Wednesday 18th August 2010
quotequote all
I've had this with a loose plug extender, it touches the manifold at high speed and shorts out. Temp fix is using a cable tie to hold the lead up.

Barkychoc

7,848 posts

235 months

Wednesday 18th August 2010
quotequote all
Had exactly this in the V8S.
I never did really get to the bottom of it before rebuilding the engine - but the cam was pretty tired when it was stripped down.
Nothing has been changed electrically and its now perfect after the rebuild, and there's a big difference in performance now the cam has lobes on it.

M@H

11,298 posts

303 months

Wednesday 18th August 2010
quotequote all
ButtonIt said:
I've had this with a loose plug extender, it touches the manifold at high speed and shorts out. Temp fix is using a cable tie to hold the lead up.
Hmm.. I guess if you haven't got combustion in one chamber but the exhaust is hot enough for some post ignition in the manifold then you could get a glowing header quite quickly but I am mystified as to why it would be even on both sides and with the car idling normally..

Any joy with it yet Mark?



Edited by M@H on Wednesday 18th August 13:32