Coolant temp sender upgrades
Coolant temp sender upgrades
Author
Discussion

Kitchski

Original Poster:

6,552 posts

262 months

Wednesday 18th August 2010
quotequote all
Apologies for starting a new thread, but the search function is down and the Google one is a bit, well crap.
Basically I'm taking the Chim to Blackpool in a couple of weekends for the Bring It Home meet and my temp gauge is now inoperative. It's always read low, now it doesn't read at all. Fans still work fine, car behaves 100%, but no reading on gauge.
I've read about using the LR sender with a resistor, but I've since read that that isn't the best solution as the resistor/sender combo cannot provide linear readings, and that a Ford sender with a brass adapter is the better way to go.
But then I read the Ford sender isn't compatible with certain gauges and I'm not sure which gauge I have. I've no problem physically changing the parts, but I don't know which ones to use.

It's a 1995/M Serp 4.0 with white (Old English White kinda white) gauges.

Any ideas?

Cheers

walt762

240 posts

263 months

Wednesday 18th August 2010
quotequote all
You can just replace the sender in it's existing position just by removing the dizzy cap, these can be bought from "Clever Trevor"
http://www.clever-trevor.net/search-car-category.h...
third from the bottom, a bit fiddly but can be done fairly easily.
You could alternatively fit the correct sender (as above) in the Rover location & get a brass adaptor to suit.

spend

12,581 posts

282 months

Thursday 19th August 2010
quotequote all
First try touching the sender connector to ground, if it doesn't move the gauge (ignition on) the gauge/wiring is broken, if the gauge goes full scale either the connection is bad or the sender needs replacing. It is quite rare for the senders to fail, removing & cleaning all the scale/scum of the sensor tip will probably make it more accurate BTW.

Kitchski

Original Poster:

6,552 posts

262 months

Thursday 19th August 2010
quotequote all
Will try that tonight...electrics aren't my strong point! assuming i clean it up and get it working, is it accurate enough to use?

Kitchski

Original Poster:

6,552 posts

262 months

Thursday 19th August 2010
quotequote all
Right, gauge and wiring apparently ok. Connection looks good and tight, if a little manky. Nothing major, so I think I need a new sender.
Do I go original, or take the oppourtunity to improve?

Cheers

peebee

274 posts

237 months

Friday 20th August 2010
quotequote all
I replaced with the LR unit and a variable resistor. It may not move in a linear manner (although not sure I would notice) but I then ran the engine until the fans cut in, set the variable resistor so that the guage read 90 degrees and job done. It doesn't matter to me whether it's accurate since I use it to monitor abnormal temperature - generally looking out for over heating, which thankfully I haven't had.

Kitchski

Original Poster:

6,552 posts

262 months

Sunday 22nd August 2010
quotequote all
Forgive my lack of electric knowledge but where do I buy a resistor like this? Maplin? How do you set it up?

Simon says

19,466 posts

252 months

Sunday 22nd August 2010
quotequote all
peebee said:
I replaced with the LR unit and a variable resistor. It may not move in a linear manner (although not sure I would notice) but I then ran the engine until the fans cut in, set the variable resistor so that the guage read 90 degrees and job done. It doesn't matter to me whether it's accurate since I use it to monitor abnormal temperature - generally looking out for over heating, which thankfully I haven't had.
yes 200k variable resistor as i seem to remember(been fitted for about 3 years now)reads very early from cold so if you have any signs of running hotter than usual then the needle will plant itself in the hot zone which is exactly what we are interested in,mine never registers above an indicated 90 in traffic and just over 80 on the move wink Kitchski Maplins yes or R.S components.



Edited by Simon says on Sunday 22 August 10:31

Kitchski

Original Poster:

6,552 posts

262 months

Sunday 22nd August 2010
quotequote all
Simon says said:
peebee said:
I replaced with the LR unit and a variable resistor. It may not move in a linear manner (although not sure I would notice) but I then ran the engine until the fans cut in, set the variable resistor so that the guage read 90 degrees and job done. It doesn't matter to me whether it's accurate since I use it to monitor abnormal temperature - generally looking out for over heating, which thankfully I haven't had.
yes 200k variable resistor as i seem to remember(been fitted for about 3 years now)reads very early from cold so if you have any signs of running hotter than usual then the needle will plant itself in the hot zone which is exactly what we are interested in,mine never registers above an indicated 90 in traffic and just over 80 on the move wink Kitchski Maplins yes or R.S components.



Edited by Simon says on Sunday 22 August 10:31
Excellent, thanks. Does this just sit in the wiring before the sensor? I take it I have to adjust it to read approx 90 degrees when the fans begin kicking in? And fit a ring terminal to the wiring?


Kitchski

Original Poster:

6,552 posts

262 months

Wednesday 25th August 2010
quotequote all
Just been into RS Components and was met with 87 different types of 200k resistor, none of which look like what i'd expected. Would anyone know of any fitting guides available because I'm struggling to work it out!

Simon says

19,466 posts

252 months

Wednesday 25th August 2010
quotequote all
Kitchski said:
Just been into RS Components and was met with 87 different types of 200k resistor, none of which look like what i'd expected. Would anyone know of any fitting guides available because I'm struggling to work it out!
Look like this http://www.satistronics.com/variable-resistor-204-... and just set up as in Peebee's post smile once you have set it insulate the unit well with some insulation tape thumbup i have mine slightly over reading so at normal road speed it sits in the middle knowing that if temps go near abnormal the gauge will plant itself to 3/4 + smile

Edited by Simon says on Wednesday 25th August 10:42

Kitchski

Original Poster:

6,552 posts

262 months

Wednesday 25th August 2010
quotequote all
I did see one like that, thanks. So it just wires in next to the sensor? I'm guessing one feed from the sensor, one to gauge and one to earth?