Those that have done a body off or chassis restoration......
Discussion
Those of you that have done a body off chassis restoration or partial lift, can I ask how much you spent in general to get the bits done and back together ?
• Cost for striping and coating of chasis = ?
• Total spent between taking car apart and putting back on the road (including all the small jobs) = ?
I’m considering doing a body off at some point this winter but I’ve costed a few bits up and its coming out to about £3,000 if none of the chassis needs replacing !
So if the outriggers are shot it could be over 4k !
This includes all the little jobs I’d like to do at the same time which include but not limited to : Racing reds, poly bushes, new rad, silicone hoses, ball joints, tie rod ends, wheel bearings, fuel hoses, clutch hose, PAS hoses, engine mounts & throttle cable.
I think I might want to do more that I can afford (or have the time and energy to do).
Are there essential items that should be renewed / replaced while the body is off ?
• Cost for striping and coating of chasis = ?
• Total spent between taking car apart and putting back on the road (including all the small jobs) = ?
I’m considering doing a body off at some point this winter but I’ve costed a few bits up and its coming out to about £3,000 if none of the chassis needs replacing !
So if the outriggers are shot it could be over 4k !
This includes all the little jobs I’d like to do at the same time which include but not limited to : Racing reds, poly bushes, new rad, silicone hoses, ball joints, tie rod ends, wheel bearings, fuel hoses, clutch hose, PAS hoses, engine mounts & throttle cable.
I think I might want to do more that I can afford (or have the time and energy to do).
Are there essential items that should be renewed / replaced while the body is off ?
Last year due to needing an engine rebuild as a result of slipped liners I took the plunge and did a full body off chassis refurb.
My chassis wasnt rusted thro it was mainly surface rust where the plastic coating had split and allowed water underneath so it didnt need new outriggers, but it did look very tatty. Fentec in Peterboro blast cleaned and powder coated chassis, suspension arms, rear uprights, and a slection of other chassis bits for just under £250 inc VAT and they did a first class job.
I spent a total of £10500 (ouch) this included 5.5k on the engine at V8D, and the remaining 5k spent on;
Steve Heath arb links and powerflex bushes
Nitron dampers & springs
Upgrade front brake to Granada cosworth calipers & 283MM EBC grooved/dimpled discs
Upgrade rear brakes to EBC g/d discs and new calipers
TVR Power braided brake hoses & new brake pipes
New wheel bearings all round
New top & bottom ball joints to front suspension
New engine, gearbox & exhaust mounts
ACT hoses etc
New foil heatshield in engine bay and repaint engine bay
All suspension components were either zinc plated or powder coated
Stainless steel fixings for non safety critical areas.
Plus a variety of other miscellaneous bits and bobs whose cost mounted up surprisingly quickly
Apart from the engine build, the powder coating, and zinc plating I did all the work myself in my home garage during a quiet couple of months when I was 'self unemployed'.
I shopped around a lot for parts and found TVR Power took a lot of beating for many parts, Andy was a big help and offered some unbeatable prices when I sent over a list of requirements.
The EBC brake discs came from Graham Goode in Leicester no-one else came close on price for these.
I also had the friendly help of my local garage South Lincs Autos near Spalding who allowed me use of one of their workshop bays to fit the engine and more than a little help from both Steve amd Mark there.
And yes it is like a new car, but then it should be for the money spent! I hope it'll last more than 10 years.
Its not a task to be taken on lightly, I have done other 'body off' car restorations in the past (Austin Healey and TR6) so have a little experience of having the garage full of dismantled car for several years, I didnt want the TVR to drag on and had the time to concentrate on the task so if you are short on time and motivation I would suggest tailoring your ambition accordingly.
ETA: just found a pic I posted last year to show the standard you can expect if spending that amount on your chassis refurb,

My chassis wasnt rusted thro it was mainly surface rust where the plastic coating had split and allowed water underneath so it didnt need new outriggers, but it did look very tatty. Fentec in Peterboro blast cleaned and powder coated chassis, suspension arms, rear uprights, and a slection of other chassis bits for just under £250 inc VAT and they did a first class job.
I spent a total of £10500 (ouch) this included 5.5k on the engine at V8D, and the remaining 5k spent on;
Steve Heath arb links and powerflex bushes
Nitron dampers & springs
Upgrade front brake to Granada cosworth calipers & 283MM EBC grooved/dimpled discs
Upgrade rear brakes to EBC g/d discs and new calipers
TVR Power braided brake hoses & new brake pipes
New wheel bearings all round
New top & bottom ball joints to front suspension
New engine, gearbox & exhaust mounts
ACT hoses etc
New foil heatshield in engine bay and repaint engine bay
All suspension components were either zinc plated or powder coated
Stainless steel fixings for non safety critical areas.
Plus a variety of other miscellaneous bits and bobs whose cost mounted up surprisingly quickly
Apart from the engine build, the powder coating, and zinc plating I did all the work myself in my home garage during a quiet couple of months when I was 'self unemployed'.
I shopped around a lot for parts and found TVR Power took a lot of beating for many parts, Andy was a big help and offered some unbeatable prices when I sent over a list of requirements.
The EBC brake discs came from Graham Goode in Leicester no-one else came close on price for these.
I also had the friendly help of my local garage South Lincs Autos near Spalding who allowed me use of one of their workshop bays to fit the engine and more than a little help from both Steve amd Mark there.
And yes it is like a new car, but then it should be for the money spent! I hope it'll last more than 10 years.
Its not a task to be taken on lightly, I have done other 'body off' car restorations in the past (Austin Healey and TR6) so have a little experience of having the garage full of dismantled car for several years, I didnt want the TVR to drag on and had the time to concentrate on the task so if you are short on time and motivation I would suggest tailoring your ambition accordingly.
ETA: just found a pic I posted last year to show the standard you can expect if spending that amount on your chassis refurb,
Edited by MisterT on Friday 20th August 16:46
Edited by MisterT on Friday 20th August 16:47
Barkychoc said:
I think most of us that have done a body off have a wife - so the best plan is to not keep a total!
I would say that you're looking at spending the best part of the cost of a new kitchen, just keep that to yourself though eh?
I would say that you're looking at spending the best part of the cost of a new kitchen, just keep that to yourself though eh?


Absolutely true. Im pretty sure there are a few that had a wife when they started,
but not by the time they had finished.I did a partial lift 2 years ago didnt cost that much but that said I took a different approach spread the cost over 2 years
1st year
Do the lift 2" doesn't cost anything to do if you do it by yourself.
brought a complete poly bush kit approx £300.
cleaning and painting chassis with por15 approx £70
Extra's I went a bit OTT on the front suspension which wasnt necessary £50 for upper and lower ball joints.
£100 for the wishbones to be stripped and powder coated.
2nd year
rear suspension stripped and powder coated £120
fit the rest of the poly bush kit
renew rear wheel bearing £48
Complete geo set-up £80.
All in I reckon it's cost £800 with buying new nuts/bolts, anti freeze, but the biggest out lay the poly bushes but these are well worth it transformed the cars ride. To be honest you could perpare and popr15 the wishbones but i got so feed up doing the chassis i thought it would be easier to let someone else do it.
1st year
Do the lift 2" doesn't cost anything to do if you do it by yourself.
brought a complete poly bush kit approx £300.
cleaning and painting chassis with por15 approx £70
Extra's I went a bit OTT on the front suspension which wasnt necessary £50 for upper and lower ball joints.
£100 for the wishbones to be stripped and powder coated.
2nd year
rear suspension stripped and powder coated £120
fit the rest of the poly bush kit
renew rear wheel bearing £48
Complete geo set-up £80.
All in I reckon it's cost £800 with buying new nuts/bolts, anti freeze, but the biggest out lay the poly bushes but these are well worth it transformed the cars ride. To be honest you could perpare and popr15 the wishbones but i got so feed up doing the chassis i thought it would be easier to let someone else do it.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


