crank pulley removal
crank pulley removal
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Saturday 21st August 2010
quotequote all
Before i employ my brute force party piece any tips to removing this little sod?
Which way will the nut turn lol
Cheers

Ant.

5,254 posts

312 months

Saturday 21st August 2010
quotequote all
Meatball said:
Before i employ my brute force party piece any tips to removing this little sod?
Which way will the nut turn lol
Cheers
Car in gear, handbrake on, and someone sitting in it standing on the brakes.

15/16" socket and short extension, power bar and then standing over the O/S wing pull the from N/S to O/S.

Just torqued mine back up yesterday with the engine on the stand....

Meatball

Original Poster:

1,638 posts

241 months

Saturday 21st August 2010
quotequote all
Ant. said:
Meatball said:
Before i employ my brute force party piece any tips to removing this little sod?
Which way will the nut turn lol
Cheers
Car in gear, handbrake on, and someone sitting in it standing on the brakes.

15/16" socket and short extension, power bar and then standing over the O/S wing pull the from N/S to O/S.

Just torqued mine back up yesterday with the engine on the stand....
Nice one thanks

Meatball

Original Poster:

1,638 posts

241 months

Saturday 21st August 2010
quotequote all
Quinny said:
Better still.... if you have access to one.... Use an air impact gun or even a battery powered impact gun.... It'll whizz it off in no timesmile

And if you haven't got a 15/16 socket......24mm will also fitsmile

I tried a 24mm socket but it was too loose, ive got a 15/16 socket but my 1/2" drives broke frown Happy days
Ill sort it in the week
Cheers

Meatball

Original Poster:

1,638 posts

241 months

Saturday 21st August 2010
quotequote all
To be fair the 15/16 sockets not that tight either and the bolts not rounded?, i guess its the angle im pulling from.
Cheers

adyw

388 posts

274 months

Saturday 21st August 2010
quotequote all
Ben, are you going the whole hog with the MS installation

Meatball

Original Poster:

1,638 posts

241 months

Saturday 21st August 2010
quotequote all
adyw said:
Ben, are you going the whole hog with the MS installation
Yes mate, its about time i pulled my finger out

adyw

388 posts

274 months

Saturday 21st August 2010
quotequote all
woohoo good man, you wont be disapointed driving

Simon says

19,466 posts

252 months

Saturday 21st August 2010
quotequote all
adyw said:
woohoo good man, you wont be disapointed driving
No you won't Ben the man is right thumbup 24mm worked twice for me,don't make the mistake i made and not renew the front oil seal while your at it scratchchin mine leaked after a couple of days guess that's what you get with an original unmolested motor rolleyes thought i would do all this when i renew the cam gear in the winter but the engine thought otherwise mad a drip of non hard setting locking compound(blue)on a new bolt would not go amiss either wink keep us updated with progress thumbup

Edited by Simon says on Saturday 21st August 20:12

spend

12,581 posts

282 months

Sunday 22nd August 2010
quotequote all
Why would removing the pulley have anything to with the front oil seal? Unless you bolted on a cheese grater instead of a trigger wheel hehe

Simon says

19,466 posts

252 months

Sunday 22nd August 2010
quotequote all
spend said:
Why would removing the pulley have anything to with the front oil seal? Unless you bolted on a cheese grater instead of a trigger wheel hehe
Didn't help the fact i had used my front pulley as a press adaptor to do rear wheel bearings on a Renault Clio followed by attacking my front cover with the die grinder allowing all the swarf to enter the exposed hole Spend hehe

Meatball

Original Poster:

1,638 posts

241 months

Sunday 22nd August 2010
quotequote all
Simon says said:
followed by attacking my front cover with the die grinder allowing all the swarf to enter the exposed hole Spend hehe
Was this to get the sensor bracket to fit Simon?
It was going to be my next question hehe

Edited by Meatball on Sunday 22 August 11:37

Simon says

19,466 posts

252 months

Monday 23rd August 2010
quotequote all
Meatball said:
Simon says said:
followed by attacking my front cover with the die grinder allowing all the swarf to enter the exposed hole Spend hehe
Was this to get the sensor bracket to fit Simon?
It was going to be my next question hehe

Edited by Meatball on Sunday 22 August 11:37
Yes Ben it was smile and of course take measures with some kitchen roll or similar to stop those ally filings going where they shouldn't i was joking in my last post of course rolleyes