Rocker Cover removal
Discussion
The subject is covered in the Griffith & Chimaera Resource, downloadable from www.RV8R.co.uk
The Land Rover parts numbers are included as they can be difficult to source from other routes.
I used a long reach 3/8" socket. Went in the recess easily.
One point to note: My car previously had been serviced at a main dealers or well known specialist, yet the bolts had been tapped open on one occasion. Two of them were quite badly damaged.
The 12 point bolts are used as a fair amount of torque is required and such bolts spread the load efficiently.
The Land Rover parts numbers are included as they can be difficult to source from other routes.
I used a long reach 3/8" socket. Went in the recess easily.
One point to note: My car previously had been serviced at a main dealers or well known specialist, yet the bolts had been tapped open on one occasion. Two of them were quite badly damaged.
The 12 point bolts are used as a fair amount of torque is required and such bolts spread the load efficiently.
Edited by Derek Smith on Monday 23 August 15:55
spend said:
Derek Smith said:
The 12 point bolts are used as a fair amount of torque is required and such bolts spread the load efficiently.
Respectfully... load of crap IMHO...It is what I was told by staff at Namrick. They didn't stock the items but advised me against an allen key replacement. Their actual quote is in the Resource. I can't support their suggestion, I'm only repeating what I was told.
Quinny said:
My own view is that, in this application, clamping force is hardly an issue.. Therefore an allen headed bolt, a normal hex bolt, or a 12 point bolt is largly irrelevent
Probably the best solution is a stud, which you could drop the gasket over and then the cover, and then put a nut on, is probably the best way.... But even that is not "really" necessary...
(Disclaimer)
IMO of course
I don't think I put over correctly what the chap at Namrick meant.
Probably the best solution is a stud, which you could drop the gasket over and then the cover, and then put a nut on, is probably the best way.... But even that is not "really" necessary...
(Disclaimer)
IMO of course

It wasn't so much the torque required to do the nut up as undo it. I mentioned the struggle I had with two or three of the bolts, hence the conversation. Nowadays, rocker covers stay on for years without being moved. Indeed, the only reason I removed mine was to paint them. A steel bolt into aluminium can, over a few years, form a bond somewhat more secure than that with Jordan and her husband (whose name I forget - which pleases me).
That was his point. Sorry to confuse.
You should tell the chap about copper slip, and the real necessity to ensure SSteel is lubricated before use in ally tappings.
Decent cap heads are fine for the torque on the rocker covers, but I much prefer studs and subtly trick nuts
Fitting everything with studs takes 10% of the time, which is a big deal for those of us that have to make regular valve clearance checks.
Decent cap heads are fine for the torque on the rocker covers, but I much prefer studs and subtly trick nuts
Fitting everything with studs takes 10% of the time, which is a big deal for those of us that have to make regular valve clearance checks.
Where a ferrous metal like steel meets a non-ferrous metal like aluminium a condition known as electrocatalytic corrosion can occur.
When the third element "water" is introduced the two metals combine to create a similar chemical reaction to a battery.
The result is the production of acids that significantly accelerate corrosion.
However I am pretty sure stainless & aluminium would not be nearly as big a problem as mild steel & aluminium.
The worst example of electrocatalytic corrosion I have seen was on an AC Ace where the steel superleggera frame met the aluminium body.
That job made our outrigger replacement seem like a walk in the park.
Chimpaholic said:

Where a ferrous metal like steel meets a non-ferrous metal like aluminium a condition known as electrocatalytic corrosion can occur.
When the third element "water" is introduced the two metals combine to create a similar chemical reaction to a battery.
The result is the production of acids that significantly accelerate corrosion.
However I am pretty sure stainless & aluminium would not be nearly as big a problem as mild steel & aluminium.
I recently got my rocker covers off to have a look at the rockers and shafts. Although worn they arent too bad. I then took off the inlet manifold and the valley gasket to have a look at the cam and followers.
The front valley gasket bolt came undone but....you can tell where this is going.....the rear bolt just necked off, leaving about 3mm sticking proud of the block.
My neighbours learnt a few new swear words shortly afterwards.
Having had a closer look at the little b
stard it looks like the bolt has corroded/welded itself to the block. The bolt's obviously never been out since the car was built, so with 10 years of moisture and heat/cool cycles, its become one with the block.Managed to drill through it into the bolt hole cavity beneath the bolt and fill it with penetrating oil, but the annoying thing wont come out. Ive tried the usual easy outs, but dont want to bugger the block.
So its engine out time and take it off to a machine shop to be drilled out and helicoiled.
On the bright side, it will give me the excuse I was after to go through the engine and give it a bit of an overhaul - new cam, followers, mains and big end bearings, timing chain and sprockets etc etc etc etc.
Happy days
Cheers
Marty
To add insult to injury, I cant get the crank pulley bolt off either. Once I get the block out of the car I'll get a bit more medieval with it. Had the wife sat in the car with both feet on the brake pedal, and car in gear. I managed to get the car to move by trying to undo the crank bolt with a long breaker bar, which was bending too. At this point I gave up.
Its all part of the 'experience' I guess.
Edited by Marty V8 on Wednesday 25th August 22:27
Chimpaholic said:

Where a ferrous metal like steel meets a non-ferrous metal like aluminium a condition known as electrocatalytic corrosion can occur.
When the third element "water" is introduced the two metals combine to create a similar chemical reaction to a battery.
The result is the production of acids that significantly accelerate corrosion.

Mark S
Marty V8 said:
Chimpaholic said:

Where a ferrous metal like steel meets a non-ferrous metal like aluminium a condition known as electrocatalytic corrosion can occur.
When the third element "water" is introduced the two metals combine to create a similar chemical reaction to a battery.
The result is the production of acids that significantly accelerate corrosion.
However I am pretty sure stainless & aluminium would not be nearly as big a problem as mild steel & aluminium.
I recently got my rocker covers off to have a look at the rockers and shafts. Although worn they arent too bad. I then took off the inlet manifold and the valley gasket to have a look at the cam and followers.
The front valley gasket bolt came undone but....you can tell where this is going.....the rear bolt just necked off, leaving about 3mm sticking proud of the block.
My neighbours learnt a few new swear words shortly afterwards.
Having had a closer look at the little b
stard it looks like the bolt has corroded/welded itself to the block. The bolt's obviously never been out since the car was built, so with 10 years of moisture and heat/cool cycles, its become one with the block.Managed to drill through it into the bolt hole cavity beneath the bolt and fill it with penetrating oil, but the annoying thing wont come out. Ive tried the usual easy outs, but dont want to bugger the block.
So its engine out time and take it off to a machine shop to be drilled out and helicoiled.
On the bright side, it will give me the excuse I was after to go through the engine and give it a bit of an overhaul - new cam, followers, mains and big end bearings, timing chain and sprockets etc etc etc etc.
Happy days
Cheers
Marty
To add insult to injury, I cant get the crank pulley bolt off either. Once I get the block out of the car I'll get a bit more medieval with it. Had the wife sat in the car with both feet on the brake pedal, and car in gear. I managed to get the car to move by trying to undo the crank bolt with a long breaker bar, which was bending too. At this point I gave up.
Its all part of the 'experience' I guess.
Edited by Marty V8 on Wednesday 25th August 22:27
Not sure if it helps but I did watch this trick once, it seemed to work.
I think you have covered step 1 & 2 already but I will detail the complete process.
1) Use a centre punch to put a dot in the centre of the bolt shaft
2) Drill to the correct size for your chosen EasyOut, do not introduce the EasyOut yet
3) Source a thin tip diesel glow plug and hook it up to a 12 volt supply, a jump lead is perfect
4) The glow plug will glow red hot so don't touch it
5) Hold the tip of the glow plug against the top of exposed part of the sheared bolt where you drilled the hole for the EasyOut
6) Wait till the sheared bolt shaft is as hot as you dare get it
7) Insert the EasyOut, give it a light tap to get it to bite & turn slowly
When I saw this demonstrated it took two attempts.
During the second attempt a small amount of cold water was added to the sheared bolt shaft using a pipette between step 6 & 7.
Basically the idea is to introduce a very direct source of heat down the sheared bolt shaft only, without all the heat being drawn out by the surrounding ally.
Just like when you do any Mig welding the car battery should be disconnected to protect the ECU & Alternator diode pack.
I'm not saying this trick will work for you but it definitely worked when I saw it demonstrated.
Sounds like a good plan, however I am past that stage now (unfortunately) and I think that I may have touched the thread with the easy out no anyway. I'm going to pull the engine and it'll give me the excuse to go right through the engine and replace/renew/refurb as required.
Whilst Im on with it, I'm also contemplating a body lift to check the outriggers. Im also going to try to retro-fit air con into it.
Needless to say, Ive sorn'd it and cashed that car tax back in, cos it aint going anywhere soon.
Whilst Im on with it, I'm also contemplating a body lift to check the outriggers. Im also going to try to retro-fit air con into it.
Needless to say, Ive sorn'd it and cashed that car tax back in, cos it aint going anywhere soon.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




