Severe clonking HELP
Severe clonking HELP
Author
Discussion

biper

Original Poster:

2,097 posts

248 months

Friday 27th August 2010
quotequote all
In need of some help here guys.
Just drove to work in my Chim 500 and as I was about half a mile away I went over a pot hole and this clonking started, fortunately I was only doing about 20mph. I had to crawl the rest of the way at about 5mph or the clonking would start and sounded like it was beating the underneath of the car. I am assuming it is a half shaft, but could it be something else that I could fix in the car park. I hate the thought of the car on the back of the AA low loader and for people to point and say 'look another broken down TVR' 55 miles from home and it is pissing it down.
Any suggestions most greatfuly received.
Barrie

haircutmike

22,511 posts

235 months

Friday 27th August 2010
quotequote all
It could be many things.

When my rear diff mount became loose, it sounded awfull, really clonky, brought on by gently throttling on and off.

It would be unusual for a pot hole to bring something on but maybe a loose ARB, broken drop link etc.

Only advice is to "get under there" and thourghly check.

biper

Original Poster:

2,097 posts

248 months

Friday 27th August 2010
quotequote all
Thanks HCM
The knocking/clonking get faster and louder the faster you go, which made me think drive shaft. Still raining at the mo, so will have a look ASAP.
Thanks for the quick response.
Barrie

Edited by biper on Friday 27th August 08:57

haircutmike

22,511 posts

235 months

Friday 27th August 2010
quotequote all
Not much else under there.

Could be rear UJ on prop, usually a vibration first.

When I renewed a CV on my drive shaft last year, I did all 4 as a matter of course. If one has gone it may not be long till another wears, they were a bit of a pig to do!.

blackchim

91 posts

195 months

Friday 27th August 2010
quotequote all
think you need to determine whether its from the drive/diff or from the wheel area ie damper/spring broken or brake caliper etc. get the jack and carefully lift/take the wheel off and have a good look.

biper

Original Poster:

2,097 posts

248 months

Friday 27th August 2010
quotequote all
Ok, just had the AA take a look, broken shock absorber. I can divert to racing green on the way home (on the low loader) to pick one up. I think I will get both sides as I am at it.
I am so happy that it was nothing more major.
And thank you for your quick replies and advice. This is what PH is all about.
Barrie

Edited by biper on Friday 27th August 10:19

haircutmike

22,511 posts

235 months

Friday 27th August 2010
quotequote all
biper said:
Ok, just had the AA take a look, broken shock absorber. I can divert to racing green on the way home (on the low loader) to pick one up. I think I will get both sides as I am at it.
I am so happy that it was nothing more major.
And thank you for your quick replies and advice. This is what PH is all about.
Barrie

Edited by biper on Friday 27th August 10:19
Given the current topics, I am sure we are all interested in the make of the offender yes

biper

Original Poster:

2,097 posts

248 months

Friday 27th August 2010
quotequote all

Given the current topics, I am sure we are all interested in the make of the offender yes
[/quote]

They are the standard ones as fitted by TVR. Fooking expensive though, £176.00 each from RG.

JonathanT

880 posts

315 months

Friday 27th August 2010
quotequote all
OOI what bit of the shocks was actually broken?

biper

Original Poster:

2,097 posts

248 months

Friday 27th August 2010
quotequote all
Not very good at this, I think it is where the ram joins to the top, if that makes any sense. When I have taken them off I will try to be more precise.
When the car was jacked up on the broken side the wheel dropped a lot lower than the other side. But the S/A was still held in place, if you know what I mean. So it wasn't broken by the fixing point.


biper

Original Poster:

2,097 posts

248 months

Saturday 28th August 2010
quotequote all
Well got car home on the transporter, however when I got out of the truck I was horrified to see that the poor old Chim had sagged down on the side of the broken shocker. I had an 'UNINVITED GUEST'
Yep you guesses it, the journey home had on the back of the transporter had bumped along and thus the spring had gone throught the floor behind the passanger seat. A very neat break I have to say and will be fixed without trauma as it had not completely gone through, more like a half opened tin of beans and pushed back into position easily.
I decided not to go via RG as I could not justify £408 for two new shocks. I will take the oppotunity of upgrading all round.
The shocker itself had snapped at the ram leaving the top mounting in place simular to that of another post on here. They were I believe to be the origional Bilsteins.



Edited by biper on Saturday 28th August 12:04