a Griff eater is ready
Discussion
Certainly looks a tidy installation; must have been very satisfying to see it take shape 
The two hoses to the side of the secondary plenum, the blue is obviously a variation on the original breather; is there a check valve in there to stop positive pressure from the blower pressurising the rocker box(es)? Where does the larger black one link to?

The two hoses to the side of the secondary plenum, the blue is obviously a variation on the original breather; is there a check valve in there to stop positive pressure from the blower pressurising the rocker box(es)? Where does the larger black one link to?
Pupp said:
Certainly looks a tidy installation; must have been very satisfying to see it take shape 
The two hoses to the side of the secondary plenum, the blue is obviously a variation on the original breather; is there a check valve in there to stop positive pressure from the blower pressurising the rocker box(es)? Where does the larger black one link to?
according to SC power the plenum box is at zero pressure, there should be no pressure going back into the rockers, because I have roller rockers its not been possible to fit the splash guards in the rockers covers so a catch tank maybe required. I asked the question about the pressure, The large black pipe is the from the blow off valve which is after the charger so it dumps its air back to the intake side of the charger.
The two hoses to the side of the secondary plenum, the blue is obviously a variation on the original breather; is there a check valve in there to stop positive pressure from the blower pressurising the rocker box(es)? Where does the larger black one link to?
Edited by hiltonig on Monday 6th September 08:30
Edited by hiltonig on Monday 6th September 08:45
Most of us with the 'proper' TVR rocker covers don't have splash guards and it hasn't been a problem even with the early inferior umbrella valve stem seals (which were paired as std with the cast rocker boxes).
Viton seals are worthwhile on hot engines IMHO, they are available for Chevys in the correct sizes - as long as you can cut the recess a little further down the guide (1mm). The viton is much more tolerant of heat so lasts & works better.
You should have just run an M5 tap down the head oil holes (5 min job) before assembly, then you can fit socket set screws down the holes to block or cut a slot in the screw to set a restricted passage.
Many roller rockers allow conversion to up the push rod oiling, as long as there is provision for oiling into the rocker arm bush this is a reasonable alternative IMHO. Personally I like to shim the sides of the rocker arm to stop the oil bleeding out of the bush and still have 'some restricted' feed up the pedestals.
Obviously a lot of the criteria for the rocker arm oiling depends on how many revs you want to use, I guess you are not wanting much in the way of rpms so would have thought the simple restriction would work for you. That is also possible using pedestal shims that block off / restrict the oil supply, but TBH I find the rocker geometry is best without them. A quick tap and a couple of socket sets is hell of a lot cheaper than custom shims and a skim of all pedestals to accomodate them
Viton seals are worthwhile on hot engines IMHO, they are available for Chevys in the correct sizes - as long as you can cut the recess a little further down the guide (1mm). The viton is much more tolerant of heat so lasts & works better.
You should have just run an M5 tap down the head oil holes (5 min job) before assembly, then you can fit socket set screws down the holes to block or cut a slot in the screw to set a restricted passage.
Many roller rockers allow conversion to up the push rod oiling, as long as there is provision for oiling into the rocker arm bush this is a reasonable alternative IMHO. Personally I like to shim the sides of the rocker arm to stop the oil bleeding out of the bush and still have 'some restricted' feed up the pedestals.
Obviously a lot of the criteria for the rocker arm oiling depends on how many revs you want to use, I guess you are not wanting much in the way of rpms so would have thought the simple restriction would work for you. That is also possible using pedestal shims that block off / restrict the oil supply, but TBH I find the rocker geometry is best without them. A quick tap and a couple of socket sets is hell of a lot cheaper than custom shims and a skim of all pedestals to accomodate them

Gassing Station | Chimaera | Top of Page | What's New | My Stuff




methinks you will not be disappointed
keep us up-dated please.


