New idle stepper, now wont run at all.
Discussion
So i thought it was time to get a new stepper as im getting all sorts of idling problems that always clear up after WD-40-ing the stepper.
arrived this morning, insterted, and it started, coughed, and stopped, tried again, same problem.
is there a procedure to calibrate it or something???
arrived this morning, insterted, and it started, coughed, and stopped, tried again, same problem.
is there a procedure to calibrate it or something???
Just bought one off EBay as Im testing them with MS and the PnP ECUs. I went to fit it to my car and it wouldnt screw in as the shaft is far too long
The plug is also different, the key ways arent the same.
Anyhow, I swapped the shafts over from the original one to the new one (pull the new one and it will come out) and used a screw driver to dig the little key way out that wasnt on the original one and now it works
So the PnP ECUs work them, which is what I wanted to prove. I see no reason why the Lucas wouldnt be the same.
My old one was completely knackered though, the shaft rotated as the keyway in the valve assembly was missing!
Phil
The plug is also different, the key ways arent the same. Anyhow, I swapped the shafts over from the original one to the new one (pull the new one and it will come out) and used a screw driver to dig the little key way out that wasnt on the original one and now it works
So the PnP ECUs work them, which is what I wanted to prove. I see no reason why the Lucas wouldnt be the same.My old one was completely knackered though, the shaft rotated as the keyway in the valve assembly was missing!
Phil
daxtojeiro said:
Just bought one off EBay as Im testing them with MS and the PnP ECUs. I went to fit it to my car and it wouldnt screw in as the shaft is far too long
The plug is also different, the key ways arent the same.
Anyhow, I swapped the shafts over from the original one to the new one (pull the new one and it will come out) and used a screw driver to dig the little key way out that wasnt on the original one and now it works
So the PnP ECUs work them, which is what I wanted to prove. I see no reason why the Lucas wouldnt be the same.
My old one was completely knackered though, the shaft rotated as the keyway in the valve assembly was missing!
Phil
+1
The plug is also different, the key ways arent the same. Anyhow, I swapped the shafts over from the original one to the new one (pull the new one and it will come out) and used a screw driver to dig the little key way out that wasnt on the original one and now it works
So the PnP ECUs work them, which is what I wanted to prove. I see no reason why the Lucas wouldnt be the same.My old one was completely knackered though, the shaft rotated as the keyway in the valve assembly was missing!
Phil
I was heavy handed and broke mine screwing it back in. Bought a cheap ebay one and the car wouldn't run at all. Noticed the shaft was too long, swapped the shaft for the old one all its been perfect the last 6 months.
blitzracing said:
The shaft liength is not the whole story on these, some of the motors fit so badly in the housings they let in air, so the idle becomes very unstable. You will find there are two versions of the Lucas unit, with as you say different sockets fitted.
Can only really comment on the one I got, I have no idea if the Lucas can control it, but its working on mine with the MS and the original shaft. I have emailed the seller and complained to him, but he wants my VIN number to check compatability, hard to explain that the engine is no longer in the TVR, but for £20 Im happy its working,
Phil
I purchased intermotor part nu ETC660 from Sutton Autofactors about 40 quid.Good quality unit works a treat.
http://www.suttonautofactors.co.uk/
http://www.suttonautofactors.co.uk/

Edited by SILICONE KID on Thursday 9th September 19:37
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



