Cermachrome / Exhaist coatings
Cermachrome / Exhaist coatings
Author
Discussion

SN79

Original Poster:

18 posts

194 months

Sunday 12th September 2010
quotequote all
Seeings as so many problems in the Chim's bay seem to radiate (no pun intended) from the collosal amount of heat, is it worth me getting my manifold and downpipes stripped and treated with a ceramic coating?


Alexdaredevilz

5,697 posts

210 months

Sunday 12th September 2010
quotequote all
Would probably be easier to heat shield/wrap the parts that need to keep cooler

spend

12,581 posts

282 months

Monday 13th September 2010
quotequote all
Yes, plenty of us have had it for a few years now...

I wonder which is more technologically advanced an Egyptian mummy or the space shuttle wink

slideways

4,101 posts

252 months

Monday 13th September 2010
quotequote all
spend said:
Yes, plenty of us have had it for a few years now...

I wonder which is more technologically advanced an Egyptian mummy or the space shuttle wink
I Don't know Dave they were clever b'stards those egyptians,biggrin
I will be ringing Zircotec tomorrow for some advice on my setup,

hiltonig

3,153 posts

239 months

Monday 13th September 2010
quotequote all
You will get a shock at zircotek prices compared to cermachrome ! However both very different you pay your money and take your choice.

spend

12,581 posts

282 months

Monday 13th September 2010
quotequote all
I discounted Zircotec as soon as I discovered they could only coat externally. Insulating between the exhaust gas and metal of the exhaust just seems a very logical thing to me wink

SN79

Original Poster:

18 posts

194 months

Monday 13th September 2010
quotequote all
Iwas just going to get some of the cermachrome from Demon Tweeks, spray it and pack it off to my local matey with an oven. Wasn't too fussed, I thought the RV8 didnt respond particulalry well to exhaust mods so the drive for it was just to keep bay temps in check a bit.

Did anyone actually notice any difference whatsoever?

spend

12,581 posts

282 months

Monday 13th September 2010
quotequote all
Done properly the difference is quite amazing...

AFIK cermachrome is just a 'finish' the real coatings underneath & inside are satin black. Preparation is key, you need a fine ally oxide blast, blow off and do NOT touch (handle with sterile gloves). Then you need a very fine spray coat thin as possible just flowing yet no more, allow to air cure and then stick in the oven. Sounds simple but full of pitfalls hehe

markreilly

795 posts

203 months

Monday 13th September 2010
quotequote all
spend said:
Done properly the difference is quite amazing...
Second that..

cs174

1,271 posts

251 months

Monday 13th September 2010
quotequote all
I had the manifolds and Y-piece on my Chim ceramic coated and the under bonnet temperatures improved dramatically.

IIRC, ACT Products do an exchange service where they will supply you with refurbished manifolds (i had the pre-cats removed also) for you to have blasted and ceramic coated then fitted. Once the old manifolds and Y-piece come off to fit the new ones, you send your old ones to ACT.

This was really handy as it meant the car wasn't off the road longer than necessary and it means you have refurbished manifolds, there's no point in forking out to have them ceramic coated if they're not going to last long anyway.

I can't remember the name of the company who did the ceramic coating but I'm sure ACT will be able to advise.

HTH


SN79

Original Poster:

18 posts

194 months

Monday 13th September 2010
quotequote all
I'm not to bothered about it being off the road for a while, if it's got major chunks missing out of it I'll just take the oppurtunity to refresh everything that needs it, probably throw on new bushes etc. Wouldn't be using it till next year anyways.

macdeb

8,760 posts

286 months

Wednesday 15th September 2010
quotequote all
Had mine done and they looked great, for a while. Now not looking so good at all after only about 6k miles. Gone dull and patchy. Anyone else with this?

macdeb

8,760 posts

286 months

Wednesday 15th September 2010
quotequote all
Quinny said:
macdeb said:
Had mine done and they looked great, for a while. Now not looking so good at all after only about 6k miles. Gone dull and patchy. Anyone else with this?
Dude.... You probably just polished the finnish into oblivionhehehehe









My manifolds have gone a bit "flat" but its been over 5 years now, and I'm pretty sure they're still keeping the radiant heat in checksmile
Cool, hehe