Where do you run yours?
Discussion
Pupp said:
Lambda controller in n/s wing void with wiring above wheelarch to cabin works well
Had a look for this one in the past too when trying to run new cables to the lights. Wasn't able to poke something through. Remember it being close but never managed it - can't remember exactly what it was that prevented it.
Any tips, can can it be done through the access hatch in the wheel arch, ie. without removing the headlights?
Teetertank said:
Pupp said:
Lambda controller in n/s wing void with wiring above wheelarch to cabin works well
Had a look for this one in the past too when trying to run new cables to the lights. Wasn't able to poke something through. Remember it being close but never managed it - can't remember exactly what it was that prevented it.
Any tips, can can it be done through the access hatch in the wheel arch, ie. without removing the headlights?
Pupp said:
the lead to the sensor (in Y piece) enters engine bay above air hose (made small grommetted hole by simply filing upwards after removing air hose (looks like an exagerated keyhole) so the sensor lead piggy-backs above the air hose (no need to disturb plugs etc as it all goes through the large air hose aperture)
Got a picture of this ?I'm going to be fitting one soon. What extra wires are needed? I thought the only thing different was a temperature sensor rather than the MAF, which I was planning on using the MAF wire for.
I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?
I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?
drew.h said:
I'm going to be fitting one soon. What extra wires are needed? I thought the only thing different was a temperature sensor rather than the MAF, which I was planning on using the MAF wire for.
I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?
You are thinking along the right lines. I too am making up an adaptor cable to interface the Megasquirt to the TVR ECU.I was hoping just to make an adapter cable from the existing connector to the Mega squirt. Have I got it all wrong?
But you will need the following extra cables:
1. VR sensor input (I'm using Ford EDIS, which means you need a PIP & SAW signal)This is a 2-core screened cable.
2. Vacuum hose think it's 3 or 4mm internal
3. Ground cables - to be run separately if you want to be safe about your earthing. Large gauge recommended for those.
4. Ignition cables if you are driving coil packs directly.
The majority of wires in the existing loom can be reused, as you are hoping.
Teetertank said:
But you will need the following extra cables:
1. VR sensor input (I'm using Ford EDIS, which means you need a PIP & SAW signal)This is a 2-core screened cable.
2. Vacuum hose think it's 3 or 4mm internal
3. Ground cables - to be run separately if you want to be safe about your earthing. Large gauge recommended for those.
4. Ignition cables if you are driving coil packs directly.
The majority of wires in the existing loom can be reused, as you are hoping.
While you can re-use the existing engine loom if you really want to, why would you really want to given that it contains about a sackload of 'extra' cabling and connectors that is redundant and given that it'll be well oxidised by now. No brainer for a minimalist new loom in my book 1. VR sensor input (I'm using Ford EDIS, which means you need a PIP & SAW signal)This is a 2-core screened cable.
2. Vacuum hose think it's 3 or 4mm internal
3. Ground cables - to be run separately if you want to be safe about your earthing. Large gauge recommended for those.
4. Ignition cables if you are driving coil packs directly.
The majority of wires in the existing loom can be reused, as you are hoping.

Inner wing wiring, I use 2 wire coat hangers, bent and wrapped in the middle covered with tape. Create a hook in one end and feed through from the hole by glovebox all the way down to the fron light pod if needed . . . My WB sensor is plumbed in like this with the wiring coming out through a grommet by the air intake pipe as per others.
As for using the existing wiring, I wouldn't. I could wait to get rid of that god awful bag of bits, unnecessary wiring and reduce the wieght, increase it's durability and improve the overall tidyness of the engine bay. . .
I appreciate people wanting to keeop things standard, but standard can be improved without making it an obvious 'modification', then I'd go for that . .
As for using the existing wiring, I wouldn't. I could wait to get rid of that god awful bag of bits, unnecessary wiring and reduce the wieght, increase it's durability and improve the overall tidyness of the engine bay. . .
I appreciate people wanting to keeop things standard, but standard can be improved without making it an obvious 'modification', then I'd go for that . .
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



