Lambda probe thread size/bungs needed
Discussion
Some time back someone on these here forums posted up a link to some allen headed bolts to plug the original/stock manifold Lambda probe holes in both manifolds,would be grateful if that person could do so again
I have 12x1.25mm swimming round my had for some reason
but then there is a lot of oxygen in there too also 
but then there is a lot of oxygen in there too also 
Edited by Simon says on Sunday 19th September 10:09
Simon says said:
..didn't realize the bosses protruded so much..
They are actually rather ugly if you care to look, an attempt to get the sensor tip in the middle of the flow in the large collector I guess?As usual when you change things you have to review why existing designs were done the way they were and if it's more sensible to change them based upon new parameters... More understanding is gleaned from the decisions to dispense with / alter / modify things than actually repairing or using them IME

Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44

I just need a few tweeks and i should be

Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44

I just need a few tweeks and i should be


Edited by Simon says on Monday 20th September 10:09
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44

I just need a few tweeks and i should be


Edited by Simon says on Monday 20th September 10:09
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.

Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44

I just need a few tweeks and i should be


Edited by Simon says on Monday 20th September 10:09
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.

Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon says said:
Meatball said:
Simon let us know what you do in the end as i need to sort mine out at some point
OK Ben will do,used the car on Saturday and did some more datalogging got a real nice fuel curve at the moment,with my switchable maps hardwired I can switch between the 2 if I cock things up not needed to yet lol,my Innovate LM2 kit as finely come into its own since the recent firmware update really pleased with it now as it just works,before I was getting freezing,logging failure etc,don't you just love companies releasing hardware unfinished? 
Edited by Simon says on Sunday 19th September 18:44

I just need a few tweeks and i should be


Edited by Simon says on Monday 20th September 10:09
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.

I see that type yes I can see that making for a tidy install and no need to make up brackets I presume?
they are a bit long...they will do for now besides they are only 6 months old.Simon says said:
slightly off topic any of us lot using after-market engine management who's using the purge valve/carbon canister?
Yep, still used here.... just drive the valve off a spare output on certain rpm/load conditions being met (I forget what exactly but can check if anyone cares). Why would you not use on TBs, assuming air box(es) is/are employed? Meatball said:
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.
Did you use a plug to connect to the coil packs and if so where did you get it from.Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.

Pink_Floyd said:
Meatball said:
No mate ive got the ones that bolt onto the back of the inlet manifold/fuel rail http://cgi.ebay.co.uk/Ignition-Coil-Pack-P38-V8-Ra...
Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.
Did you use a plug to connect to the coil packs and if so where did you get it from.Its a bit of a squeeze with the twin plenum and water pipes - but its made the installation nice and tidy.

Gassing Station | Chimaera | Top of Page | What's New | My Stuff




they can come out then
I plan on pulling the motor over the autumn anyways for a freshen up so can deal with at the same time 
