Patch of oil under the clutch pedal
Patch of oil under the clutch pedal
Author
Discussion

paul100

Original Poster:

17 posts

202 months

Sunday 19th September 2010
quotequote all
Hi

Whilst cleaning the inside of '95 Chimaera 4.0, I noticed a small patch of oil on the carpet under the clutch pedal.

Any help in identifying what the problem might be would be much appreciated.

Thanks

Paul

Edited by paul100 on Sunday 19th September 23:15

Tyre Tread

10,697 posts

247 months

Sunday 19th September 2010
quotequote all
It's more likely to be brake fluid than oil I think.

Put a little on your index finger and rub it between finger and thumb. If it feels dry when its wet then almost certainly brake fluid and could be the master cylinder is weeping past the seals.

kevin63

4,661 posts

284 months

Sunday 19th September 2010
quotequote all
I would say clutch master cylinder. There are two ways of sorting it, a new master cylinder or buy a seal kit, seals can be done while cylinder is left in place, changing master cylinder is fairly easy but better done with another pair of hands on stand by.

paul100

Original Poster:

17 posts

202 months

Monday 20th September 2010
quotequote all
Thanks for your fast responses.

Will investigate further .....

kevin63

4,661 posts

284 months

Monday 20th September 2010
quotequote all
Just for the info, the Lucas seal kit is SP2102

paul100

Original Poster:

17 posts

202 months

Monday 20th September 2010
quotequote all

On closer inspection at the top of the clutch rod, there is a very slight weeping of fluid from the seal. I also checked the checked the clutch reservoir and the fluid level looked ok.

Thanks for the info Kevin. I decided to go ahead and order the seal kit.

Can anybody please point me in the direction of any instructions on how to fit the seal ?

Thanks

Paul

Teetertank

358 posts

218 months

Monday 20th September 2010
quotequote all
Take the cyliner out first (or leave in if you're sure you can do it in situ) I reckon you probably could do it without removing, but it's a bit awkward to get at from the footwell.
If you can get under the car, drain as much fluid as you can from the bleed niple on the slave cylinder. If you can't get to it, you'll have to mop out as much fluid as you can from the top of the reservoir.

You need to unclip the pedal arm from the rod/actuator. This is just one clip that swings down, then the pin comes out and you will be free to get at the assembly.

You need to pull off the rubber boot (which you can see from the footwell),then there's a circlip holding the gubins in. Remove that and the piston should pull straight out. Have some rags underneath to catch the fluid! Once you have the piston out you can remove the fork from the end, and start disassembling as required.

The seal kit comes with about 7 or so separate seals. Just identify each one and replace like for like with what you have. (The big one is for the lid on the reservoir).


paul100

Original Poster:

17 posts

202 months

Monday 20th September 2010
quotequote all

Many thanks Teetertank.

Will give it a go when the seals arrive in a couple of days !!

kevin63

4,661 posts

284 months

Monday 20th September 2010
quotequote all
It is fairly easy doing it in situ but you need to be a very slim contortionist.

paul100

Original Poster:

17 posts

202 months

Monday 20th September 2010
quotequote all
I will have to take it easy on the Weetabix then Kevin !!

When these components start to leak (albeit very slowly at the moment), do they generally tend to deterioate slowly/gradually or is there a high-risk that they will completely fail ?

Simon says

19,466 posts

252 months

Monday 20th September 2010
quotequote all
kevin63 said:
It is fairly easy doing it in situ but you need to be a very slim contortionist.
Well described wink have done 3 now like this and none have failed biggrin

kevin63

4,661 posts

284 months

Monday 20th September 2010
quotequote all
In my opinion in this case it won't just let go, the problem is the damage it can do to the carpet. If you can't do it for a few weeks you should be ok but keep an eye on the fluid level.

paul100

Original Poster:

17 posts

202 months

Monday 20th September 2010
quotequote all
I plan to fit the seals later this week, but I have a few short journeys planned between now and then. Thanks again for your thoughts on this.

Tyre Tread

10,697 posts

247 months

Monday 20th September 2010
quotequote all
Don't forget that brake fluid is excellent paint stripper so make sure you keep it well away from any paintwork and throw the rags you use to wipe things straight into the bin.

If you get any on your clothes make sure you don't then wipe it on the bodywork.

IF you do get any on paintwork then wash it off with copious amounts of water as quickly as possible.

paul100

Original Poster:

17 posts

202 months

Tuesday 21st September 2010
quotequote all
Will do Tyre Tread and thanks for the advice.