rover 4.6 HSE V8 versus TVR V8 ??what are the differences???
rover 4.6 HSE V8 versus TVR V8 ??what are the differences???
Author
Discussion

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
i guys i just found out what could be the solution at my "need more power for not too much money".i found out that the v8 4.6HSE engine were selling in Malaysia for less than 1Kpounds.was wondering is it possible to fit it in a Chimaera???what's the differences???looking at 280hp to 300hp.tks guys

spend

12,581 posts

282 months

Thursday 30th September 2010
quotequote all
Pocketed pistons, cam, heads, valves, springs, spring seats, mapping...

Rob stated pretty much that in your other thread, but he has said in the past that he's seen TVR 450 engines that look pretty much like std LR variants (but these are unlikely to be the 300bhp candidates?). I've certainly known folks I trust that have measured some TVR450's that really are BV heads (just a little left on the porting front) and pocketed pistons + skimmed head/block for a bit of CR (well the bits that were left anyway eh Derek? hehe - he's just told me your exhausts measured 1.45" which seems unusual BTW?)

dbv8

8,676 posts

251 months

Thursday 30th September 2010
quotequote all
spend said:
(well the bits that were left anyway eh Derek? hehe - he's just told me your exhausts measured 1.45" which seems unusual BTW?)
Oh yeah have a laugh at my expense!
1.45"??? what are the standard and 500 sizes?

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
how much will it takes to make around 280hp with this engine and still be reliable?

SILICONE KID

14,997 posts

262 months

Thursday 30th September 2010
quotequote all

Your the new silicone kid ,your driving every one mad and that includes me.madWhats maks the engine produce more power is the cam,heads,ported intakes etc.The 4.6 out of a range rover is made for pulling weight etc.If you want to improve your engine change the heads put a new cam in and fit a after market fueling system..or a complete rebuilt 4.6 or 5l engine.You have been told so many times even by engine specialists (v8 Racing)confusedYou keep going on about reliability,They are all reliable

if maintained ..



confused



Edited by SILICONE KID on Thursday 30th September 18:21

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
take it easy tvr brother if i drive u mad stop reading my post.u live in UK where they have V8 guru everywhere.well not here ok.i ask for help even if u have to tell me the same thing again so what??/u think i spend my money without thinking properly???sorry if it drives u mad.i thought this site was for people in need of help concerning their car.do u think i ll ask for help if i was working in UK???its ok i guess i ll go to the griffith forum then maybe they are more friendly.
SILICONE KID said:
Your the new silicone kid ,your driving every one mad and that includes me.madWhats maks the engine produce more power is the cam,heads,ported intakes etc.The 4.6 out of a range rover is made for pulling weight etc.If you want to improve your engine change the heads put a new cam in and fit a after market fueling system..or a complete rebuilt 5l engine.You have been told so many times even by engine specialists (v8 Racing)confused

SILICONE KID

14,997 posts

262 months

Thursday 30th September 2010
quotequote all
CHIMAERA1885 Read this will help you.


http://en.wikipedia.org/wiki/Rover_V8_engine



Thought you would have no problem going by those TUT TUTS
tongue out


Edited by SILICONE KID on Thursday 30th September 19:25

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
sorry i use taxi when i am in thailand and i have a pretty asian wife so i dont need to pay for a thai gal to follow me everywhere i go trying to understand the english words coming out of my mouth.tks for the link i checked already last night.i though by asking u guys i would get my answers faster.its ok i guess cant ask real questions then.tks for ur help anyway chill

v8 racing

2,064 posts

282 months

Thursday 30th September 2010
quotequote all
Ha ha dont you just love forums!!, ok before you piss me off any more, PLEASE TELL ME IF THE ROLLING FIGURES ARE AT THE WHEELS???????????
Only kidding but it would be usefull! The 4.6 you can buy would be more usefull than your 4.0, on the rv8 as a given rule for every 100cc extra in capacity you will gain 10ftlb of torque, so you instantly gain 60ftlb, outright horsepower is going to be very similar to what you have now, to get your 280 bhp from a 4.6 engine you are going to need........
Pocketed pistons to allow you to run a decent cam, a minimum of stage 3 heads, a polished and ported inlet manifold, a 45mm trumpet base, a raise in the compression ratio, and either a chip or management sytem.
There are 2 types of 450 engine we have over here, one being a stock range rover 4.6 with a mild cam and double valve springs, thats it nothing else engine wise, the other is the 450 hc, which has big valves/a bit of throat work but standard ports, it runs the same cam as the 500, tvr 435, again fitted with double valve springs, it also has pocketed pistons, both are 9.35-1 cr, and both are fitted with tvr chips.

I am not saying dont buy the 4.6 you have out there but all you will be using in effect is the short engine? There are several companies over here that will sell you a base long engine capable of the horsepower you are wanting for around the £3000 figure, dont forget to price in your labour etc to swap the engine....

spend

12,581 posts

282 months

Thursday 30th September 2010
quotequote all
dbv8 said:
spend said:
(well the bits that were left anyway eh Derek? hehe - he's just told me your exhausts measured 1.45" which seems unusual BTW?)
Oh yeah have a laugh at my expense!
1.45"??? what are the standard and 500 sizes?
@1.5" which would be 461's, you're inlets are 1.69" 460's (the old fart could read those but not the exhausts - but I'm fairly confident he got the diameter measurement correct wink ). I'll let him have some inlets to choose the best match from as soon as he wants them, I think he wants to get at it now you have those new metal thingies rofl

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
u are always the one giving me the answers i am looking for.about the dyno i am not sure.i was so surprise by the number that i really forgot if it was at the wheels.but one thing a friend of mine has a 4 litres with ACT trumpets,MA chip and a bit more.but my car is faster than his car in any gear at any speed.even him doesn't understand.the problem is i used to have a 590hp car.so i guess i need something with a bit more guts.trust me i love my car very much and will not sell it ever.been my dream car for almost 10years.i guess after ur answers i have 2 options.1 sckit but would like more feedback by owners.second get a 5litres from TVRland.ok guys i wont disturb u no more about what i should do.oh just one last question what cam can i use now which will give me a bit more power and will still be compatible with a blower in case i get one???u said the cylinder heads is basically from rover.so how about the MERLIN F85???the price seems pretty good for what u end up???i think that ll be all for now i guess tks for ur help please be patient i understand fast but need to explain to me longer.

Ant.

5,254 posts

312 months

Thursday 30th September 2010
quotequote all
rofl I love these threads!!!!


WhatifhowtowhenwherewhathowmuchBHP !!

We have all been there and had to learn along the way, and some of us still have sooo much more to learn, but the important thing is to ask the right questions and supply the right answers..


But hey I only have a lil ole 4.6.....

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
well as i told u only 10 units here and all standard.so not really easy to get the answers u need.so have no choice then asking u guys.cause u really know those cars.tks for ur understand and help.

Sparky99

87 posts

201 months

Thursday 30th September 2010
quotequote all
hehe I used to like this thread(s). Very useful info but geez even i've got the clue as to the options available now.

No more !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

chimaera1855

Original Poster:

334 posts

199 months

Thursday 30th September 2010
quotequote all
i do too.but still have a few questions.here nobody will buy my engine so i guess will have to use it.so what cam i can use now and will be able to use with supercharge too.how about the Merlin head can it be use too with a blower???ahahha dont be mad at me ok guys lol

dbv8

8,676 posts

251 months

Thursday 30th September 2010
quotequote all
spend said:
dbv8 said:
spend said:
(well the bits that were left anyway eh Derek? hehe - he's just told me your exhausts measured 1.45" which seems unusual BTW?)
Oh yeah have a laugh at my expense!
1.45"??? what are the standard and 500 sizes?
@1.5" which would be 461's, you're inlets are 1.69" 460's (the old fart could read those but not the exhausts - but I'm fairly confident he got the diameter measurement correct wink ). I'll let him have some inlets to choose the best match from as soon as he wants them, I think he wants to get at it now you have those new metal thingies rofl
Either i am very tired after a 5 hour drive or you are far too cryptic for me. Please talk in English and tell me whats going on in detail. I dont get much out of Mike.