Guys,Diff removal.
Guys,Diff removal.
Author
Discussion

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
Just removed my rack for an O/H.

Thought I might do the whiney diff at the same time.

Any hints and method for a speedy removal?

scotty_d

6,795 posts

225 months

Saturday 2nd October 2010
quotequote all
Quinny made a Youtube video think this is it cant check as my connection at work is slow.


http://www.youtube.com/user/big500#p/u/34/IQkz-s0k...

Edited by scotty_d on Saturday 2nd October 15:25

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
Thanks Scotty.

It was actually Part 9 but I didn't know it existed!

Any other tips gratefully received.


BliarOut

72,863 posts

270 months

Saturday 2nd October 2010
quotequote all
Pay someone else to do it hehe

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
BliarOut said:
Pay someone else to do it hehe
We're still in a recession, don't believe the polititions, I need to DIY rolleyes.

BliarOut

72,863 posts

270 months

Saturday 2nd October 2010
quotequote all
Lots of socket extensions through the wheel arch, Cortina bush tool to press the old bush out and allow plenty of time. It's a tt of a job yes

shpub

8,507 posts

303 months

Saturday 2nd October 2010
quotequote all
Undo diff. Hold diff, tilt 90 degrees and drop out of the chassis. Not too bad as gravity helps. Real swine putting it back though as gravity doesn't help as it tries to stop the diff from going up.

Moral is do not underestimate its weight - it is very heavy indeed! Makes the gearbox feel like a featherweight.

Alexdaredevilz

5,697 posts

210 months

Saturday 2nd October 2010
quotequote all
Give me a shout of you need a hand, or tools

p.s Yours phones busted! rolleyes

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
Can't wait.

Rear diff mount looks like apita.

Think I'll remove the fuel tank again for access.

Can I leave the prop in place to save g/box oil draining, (recently renewed!)?

shpub

8,507 posts

303 months

Saturday 2nd October 2010
quotequote all
Not really as it gets in the way...

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
shpub said:
Not really as it gets in the way...
Bugger!

TJC46

2,199 posts

237 months

Saturday 2nd October 2010
quotequote all
haircutmike said:
Can't wait.

Rear diff mount looks like apita.

Think I'll remove the fuel tank again for access.

Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
TJC46 said:
haircutmike said:
Can't wait.

Rear diff mount looks like apita.

Think I'll remove the fuel tank again for access.

Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.
Nice idea beer

roysum

961 posts

220 months

Saturday 2nd October 2010
quotequote all
haircutmike said:
TJC46 said:
haircutmike said:
Can't wait.

Rear diff mount looks like apita.

Think I'll remove the fuel tank again for access.

Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.
Nice idea beer
I left my prop in, didn't find it a problem (sorry SH). I have just responded to your O/T Q Peter !!

R

haircutmike

Original Poster:

22,511 posts

235 months

Saturday 2nd October 2010
quotequote all
roysum said:
haircutmike said:
TJC46 said:
haircutmike said:
Can't wait.

Rear diff mount looks like apita.

Think I'll remove the fuel tank again for access.

Can I leave the prop in place to save g/box oil draining, (recently renewed!)?
Measure the outer diameter of the prop end that goes in the gearbox and make yourself a temp plug [back to your blue peter days.] No seriously this works, i used a plastic cap off an aerosol which was slightly small in dia, plenty of tape later its the correct dia. Pull the prop from the gearbox insert your makeshift plug, jobs a good un. A bit more tape to hold it in situ incase you accidentally knock it, also helps. Your aiming to get the dia correct so it will seal itself against the rear oil seal in the gearbox.
Nice idea beer
I left my prop in, didn't find it a problem (sorry SH). I have just responded to your O/T Q Peter !!

R
Even better, ta Roy, (takes opportunity to check PH during an interval while watching a rom-com, yawn).

spend

12,581 posts

282 months

Sunday 3rd October 2010
quotequote all
Plenty of diffs have to be shoved quite a long way forward to get out, due to the various rear covers (particularly GKNs). Prop shaft can certainly prevent some diffs coming out, but also pushing forward so that the fore chassis xmember takes some of the weight whilst you twist the diff 90degs and then lower the rear is my preferred routine.

The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.

Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.

haircutmike

Original Poster:

22,511 posts

235 months

Sunday 3rd October 2010
quotequote all
spend said:
Plenty of diffs have to be shoved quite a long way forward to get out, due to the various rear covers (particularly GKNs). Prop shaft can certainly prevent some diffs coming out, but also pushing forward so that the fore chassis xmember takes some of the weight whilst you twist the diff 90degs and then lower the rear is my preferred routine.

The rear mount (bush) can be undone easily enough through the wheel arches just using rather a lot of extension bars and a suitable spanner 'jamming' the other side.

Get the car plenty high enough and use a jack & some pieces of wood across the chassis members so you don't get stuck holding the diff up. It's manageable when you are ready... but the dead weight can catch you out if you aren't prepared.
Thanks for that, I have just identified it as a GKN, I like Quinny's method of various straps to lower it.

spend

12,581 posts

282 months

Sunday 3rd October 2010
quotequote all
Since it is a GKN, take your time removing the prop so that you know how the speedo trigger and sensor brackets go back together. The sensor wiring may be siliconed to the sensor so you have to trace all the way up the trans tunnel to find a connector, be warned it's a nightmare to have to go back in later to fix a dodgy speedo connection hehe

Make sure you have some imperial hex sockets, those capheads on the front of the diff carriers are torqued up pretty high. The outside chassis bolts on the carriers can be bit of a PITA on early cars as they are much longer if you have the 'floating' side bush style. Patience is key, I'd advise cracking all the bolts then taking some rest & respite before manhandling the diff out. It is of course a doddle the second time around when you know exactly what you are doing and have nicely copper slipped all the fasteners.

Del 203

12,728 posts

280 months

Sunday 3rd October 2010
quotequote all
When you are putting it back dont let it drop on your arm/shoulder !!! curse

haircutmike

Original Poster:

22,511 posts

235 months

Sunday 3rd October 2010
quotequote all
Am I right in thinking that the rear mount needs to be released by the cap bolts?

If so, these are a pain to get to as they look backwards, that's why I removed the fuel tank and formed an aperture through the rear fibreglass panel!