Passat 130 PD Tdi hesitation
Passat 130 PD Tdi hesitation
Author
Discussion

meesterb

Original Poster:

58 posts

214 months

Tuesday 5th October 2010
quotequote all
I have a 2003 Passat 130 PD Sport TDI and it has been running very well up until last night. I picked the car up from having a CV boot changed (under warranty) and as I pulled away immediately noticed a slight hesitation. Keeping positive i just thought it may be some dirt dislodged in the tank and carried on home. I took it for a short drive later and it was definately struggling on part/light throttle and being very hesitant in general. It seemed to smoke a bit more also and larger throttle openings, although much smoother seemed to offer less sprightly progress.. I used the car this morning just before vsiting the garage and the 'emissions workshop light' came on and has now stayed on.... I am getting the car checked out on Friday but don't want to use in the mean time as it clearly is not a happy bunny.. Does anybody else here have similar experiences as I would like to try and understand what is causing this - it clearly seems fuel system related and I have heard a lot of dicsussion regarding faulty MAF sensors but would the failure of one of these exhibit such signs...? I would appreciate anyones experience/views on the subject. Many thanks.

TDIfurby

1,997 posts

206 months

Tuesday 5th October 2010
quotequote all
Could be MAF. Could be a number of things really. A scan with vagcom should bring up why the CEL came on the dash. Maybe try unplugging the MAF and going for a drive and see if it improves things more.

Tame Technician

2,467 posts

235 months

Wednesday 6th October 2010
quotequote all
Likely a boost leak, maybe a boost pipe adrift or split or a hole in the intercooler.

If the code it logged says MAF fault, definatly a boost leak.

When MAF's really fail, they dont log a code, when you get a boost leak it logs an erronious code.

meesterb

Original Poster:

58 posts

214 months

Wednesday 6th October 2010
quotequote all
Thanks TT, I was worried it may be injectors or pump. I will investigate and confirm. Rgds.

meesterb

Original Poster:

58 posts

214 months

Wednesday 6th October 2010
quotequote all
Quick update - have just had a look at the obvious and the Intercooler outlet (cool side) hose connection was loose. Took it for a quick drive after tightening and it was definatey better and smoother although there was a slight hiss. Upon returning from my quick test drive, the same connection was still a bit loose so I have re-tightened. There also seems to be a little bit of oil around the pipe connection as it goes into the EGR housing and also some movement (~5mm) for the metal section as it slides into the housing. I am assuming that from the design, the bulk of the sealing in this area is done by the O-ring internally..? Not an expert by any stretch but this is the third time a pipe has come off in a couple of years and I drive like a vicar..! Is it possible to upgrade the pipework or is it just a case of new OEM stuff and new/stronger clips. Thanks again for the advice it is very helpful. Rgds.

meesterb

Original Poster:

58 posts

214 months

Wednesday 6th October 2010
quotequote all
Interestingly the pipe was still leaking after tightening so after work i took the pipe off (intercooler to the plastic section) and noticed that not only the big C-clip was broken but also the o-ring seal at that end of the pipe was completely missing...... Very strange, can only assume that somebody had bodged it before and just relied on really winding up the jubilee-type clamp but without a proper seal... Do you know if these clips and o-ring seals are available through a dealer or would it be a complete new hose? If not, i'll check my nearest breaker. Thanks again.

TDIfurby

1,997 posts

206 months

Wednesday 6th October 2010
quotequote all
Best find someone to clear fault codes else you might find CEL stays on for a bit as the "Thrust sensor: negative deviation" code is likely to still be on there. (That's the code which usually pops up with a boost leak as turbo is say pushing 1.3 bar, but due to the leak, thrust sensor only sees perhaps 0.8 bar, i.e negative deviation from requested boost)

meesterb

Original Poster:

58 posts

214 months

Wednesday 20th October 2010
quotequote all
Quick update - i changes all the seals and clips and the fault codes automatically went out as soon as i started the engine. Car is now running lovely, thanks for the input.