good news and bad news...... new dizzy cap
good news and bad news...... new dizzy cap
Author
Discussion

darkcat

Original Poster:

2,354 posts

201 months

Thursday 7th October 2010
quotequote all
So i have been having some cold start misfire issues and decided to get a new cap, genuine lucas, and a rotor arm.
I cant beleive the difference!!!!!!!! starts perfectly every time now, and somehow the engine seems more "Keen"

HOWEVER!
Now its shunting like a mother f-er!!!!
trying to hold a steady speed at 30 in town is HARD...


hmm...

Sparky99

87 posts

201 months

Thursday 7th October 2010
quotequote all
Not an expert on this but would the new cap/rotor arm affect the timing setup? However the bit I don't know is if the timing wasn't correct would this amplify shunting?

More queries than answers but i'm interested in this.

darkcat

Original Poster:

2,354 posts

201 months

Thursday 7th October 2010
quotequote all
shouldnt effect timing at all no, they are fixed. I checked / adjusted my timing a couple of months ago so should be spot on still, but might fish out the timing strobe...


TVR Beaver

2,874 posts

211 months

Thursday 7th October 2010
quotequote all
Just got a new cap and arm for mine.. and it's improved on the shunting... Is the arm 'old' Lucas.... if not I'd get one.. they have the number printed on the non-contact end.... even with the 'new' Lucas units they tend not to work as well.. but usualy over time??

Chimpaholic

9,637 posts

210 months

Thursday 7th October 2010
quotequote all
Told you it was the cap & rotor arm teacher

http://www.pistonheads.com/gassing/topic.asp?h=0&a...

To solve the shunting fist you need to make sure the rest of the ignition HT side is in good health.

If you haven't done so already, change the plug leads, extenders & spark plugs for decent parts, try Tim at ACT.

If you are still shunting you have a few options.

I solved my shunting by fitting an SC Power plenum spacer, bell mouths & plenum base heat insulating gasket.

She runs smooth as a baby's bum now, but after looking at the air fuel ratio on a rolling road I expect what the plenum spacer does is mask the erratic fuelling delivered by the TVR ECU chip.

When the AFR is observed with the TVR chip installed you can see the map delivers a very lean mixture at exactly the same point shunting happens (1800 - 2200 RPM).

I did a second run with the Mark Adams Tornado chip and the AFR is very linear throughout the rev range, as such it delivers a richer mixture at 1800 - 2200 RPM.

I wouldn't mind betting that's how the Mark Adams chip eliminates shunting.



The SC Power plenum spacer works out a bit cheaper as a shunting solution than the Mark Adams chip, so its your choice.

The most important thing before you spend out on a plenum spacer or a chip is to make 100% sure all the basics are in rude health first.

To be honest there are so many possible reasons you are shunting after a set of leads and extenders it may well pay to have someone with a Sun tester and some TVR RV8 knowledge have a look at it.

darkcat

Original Poster:

2,354 posts

201 months

Thursday 7th October 2010
quotequote all
Yes chimpaholic you did :-D (Hat off)

all ignition parts are new(ish) new coil, magnacore leads, new plugs, new extenders.

ive been looking at the planum spacer, and big-bore induction kit from ACT, however having just had the clutch replaced, im a bit short of the old reddies at the mo....

TVR Beaver

2,874 posts

211 months

Thursday 7th October 2010
quotequote all
I thought it was a before / after issue?.. why get into Plenum bases and chips?? Isn,t it somethings thats been done recently thats caused the problem? or am I not understanding??

Chimpaholic

9,637 posts

210 months

Thursday 7th October 2010
quotequote all
I would say its the plenum spacer itself that made the biggest difference to the shunting on my Chim.

The bell mouths and insulating gasket are "nice to haves" but not essential.

SC Power sells just the Plenum Spacer and extended bolts for £111.62.

You can always remove your existing trumpets, drop them by 10mm or so and re-fit for no cost.

I bet if you did all this you would solve your shunting for less than £120.00 and a mornings work.

This has to be the best and most cost effective solution if my results are anything to go by.

Good luck, hope you get it sorted.

NB: A worn cam can also make the car much smoother in my experience, you can have mine if you want rofl

Chimpaholic

9,637 posts

210 months

Thursday 7th October 2010
quotequote all
TVR Beaver said:
I thought it was a before / after issue?.. why get into Plenum bases and chips?? Isn,t it somethings thats been done recently thats caused the problem? or am I not understanding??
Good point, but we should clarify with the OP.

Darkcat: Was it shunting before the distributor cap issue?

In my defence I did say the following in my first response:

"The most important thing before you spend out on a plenum spacer or a chip is to make 100% sure all the basics are in rude health first"

"To be honest there are so many possible reasons you are shunting after a set of leads and extenders it may well pay to have someone with a Sun tester and some TVR RV8 knowledge have a look at it"

TVR Beaver

2,874 posts

211 months

Thursday 7th October 2010
quotequote all
indeed.. I have a spacer (insulation thing yet to fit) but also got shorter flared trumpets on my 500.. it actualy made the shunting more noticable... I think a longer trumpett with straight walls can help the 500's (TVR did it for a reason)... once you open them up to flared items and shorter i think you can get more cross charge from reverse flow at valve crossover.. you can mask this for sure.. one thing i've done is move my vac pipe closer to the butterfly so it advances the spark sooner.. it now shunts a bit at 1.4 / 1.5k but I'm not bothered there.. 1.8 / 2.0K is a right pain in the backside as it's about 30mph in 4th...