Discussion
Thinking of making a gig and fabricating some stainless steel units.
My plan is to scallop the bottom tubes to allow for the top of tghe tubes to be welded from the under side and then weld in the scallop and weld the bottom, so no need for a body lift.
I will be using NIIti TIG rods for the joints on the orginal chassis.
When I fabricated the gig is there anyone intrested in a set of stainless steel outriggers?
(I work for a very good eng firm so will be well made and in 316 grade)
Email if intrested.
Cheers
My plan is to scallop the bottom tubes to allow for the top of tghe tubes to be welded from the under side and then weld in the scallop and weld the bottom, so no need for a body lift.
I will be using NIIti TIG rods for the joints on the orginal chassis.
When I fabricated the gig is there anyone intrested in a set of stainless steel outriggers?
(I work for a very good eng firm so will be well made and in 316 grade)
Email if intrested.
Cheers
Nice to here that there is no need to scallop the pipe.
We use a TIG filler rod with a very high nickel content on some of our fabrications for the north sea with out any failure rate to my knowledge.
Few questions:
Do you have to take the battery box out to access the bolt through the passenger side plate in the front wheel arch?
Does the body work need supporting while the outrigger is being repalced?
Cheers
We use a TIG filler rod with a very high nickel content on some of our fabrications for the north sea with out any failure rate to my knowledge.
Few questions:
Do you have to take the battery box out to access the bolt through the passenger side plate in the front wheel arch?
Does the body work need supporting while the outrigger is being repalced?
Cheers
minkybob said:
Nice to here that there is no need to scallop the pipe.
We use a TIG filler rod with a very high nickel content on some of our fabrications for the north sea with out any failure rate to my knowledge.
Few questions:
Do you have to take the battery box out to access the bolt through the passenger side plate in the front wheel arch?
Does the body work need supporting while the outrigger is being repalced?
Cheers
You do need to remove the battery box, yes. And the bolt's buried right down at the back of the footwell....total PITA to get to, especially on the drivers side. Much more access if you remove the steering wheel and seats.We use a TIG filler rod with a very high nickel content on some of our fabrications for the north sea with out any failure rate to my knowledge.
Few questions:
Do you have to take the battery box out to access the bolt through the passenger side plate in the front wheel arch?
Does the body work need supporting while the outrigger is being repalced?
Cheers
In theory, no, as long as you put no extra weight on it, and perhaps leave the roof on for rigidity. Question is, why do it? Raising the body is a pretty simple excercise and I personally cannot for the life of me see how anyone can complete a weld on all the tubing with the body in situ. I'm not saying it can't be done. I'm saying I'd be very interested to see it done, because having raised the body and replaced mine, I cannot imagine even attempting to do it without the lift! It was a faff with it up as far as access goes, and for some reason I managed to get 8inches clearance....more than most manage.
I would say you'd need to protect the 316 in in the same way as you would a steel one; say waxoil or whatever your preferred method is. 316 will pit over time and may also rot due to crevice corrosion where the chassis meets the body work.....build up of salt / concentrated salt solutions is the main culprit. I've seen this loads of times in the offshore industry. Will try and dig out some pictures to let you see what can happen in reasonably benign conditions.
Its only been about 4 years since we pioneered "body in situ" complete outrigger replacement and have supplied/ supplied and fitted over 40 pairs now....so I think I can safely say it can be done and all tubes can be fully welded, lots of customers can't afford or indeed need a fully body off restoration which is why its proved so popular for us and we have a long list of satisfied customers, probably why every man and his dog is jumping on the "we replace outriggers" band wagon and are having a jig knocked up to make them...ours are made on our chassis jig. The stainless / mild steel debate raged on a few years ago, basically stainless is just not the right material to weld to a mild steel chassis and have wishbones bolted through the outriggers....imho
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


