What/Which gaskets?
Discussion
I am going to replace the exhaust gaskets.
My question is any old motor factor or specialist dealer/parts supplier? Are simply just RV8 gaskets or are they special?
Will the ports surfaces need cleaning therefore requiring full removal?
This would, I assume, require disconnecting the manifold from the Y piece, so will I need to get gaskets for the connection to the Y piece as well?
I have started getting tooled up (thanks for the advice in my previous post). The good news so far is the top 4 bolts on the drivers side are loose (slightly worryingly easy to get loose).
Now just need to try and reach the bottom ones!
Kwacker
My question is any old motor factor or specialist dealer/parts supplier? Are simply just RV8 gaskets or are they special?
Will the ports surfaces need cleaning therefore requiring full removal?
This would, I assume, require disconnecting the manifold from the Y piece, so will I need to get gaskets for the connection to the Y piece as well?
I have started getting tooled up (thanks for the advice in my previous post). The good news so far is the top 4 bolts on the drivers side are loose (slightly worryingly easy to get loose).
Now just need to try and reach the bottom ones!
Kwacker
I have just bought some gaskets off ebay...£13 inc postage for metal big bore gaskets...looko much better than the tat i put on a couple of years ago...they have a slightly larger opening as well which is good and seem to fit perfectly.
There are no gaskets on the Y section if you have the aero clamps and not the flanges.
Clean up all faces as much as you can as it makes getting a good seal easier.
Have a look at my thread below...Ticking something or other...people have put some good pointers on their.
There are no gaskets on the Y section if you have the aero clamps and not the flanges.
Clean up all faces as much as you can as it makes getting a good seal easier.
Have a look at my thread below...Ticking something or other...people have put some good pointers on their.
I bought the real steel 'high performance' gaskets for my V8S - I was very sceptical but trust me I have tested them extensively
and they have help up well - no leaks at all.
The price is also for a set not each, £10.81 a set on page 10.
These are apparently buick gaskets from the States.
I've also got Nord Lock washers, I think they came from ACT via ebay.
http://www.realsteel.co.uk
and they have help up well - no leaks at all. The price is also for a set not each, £10.81 a set on page 10.
These are apparently buick gaskets from the States.
I've also got Nord Lock washers, I think they came from ACT via ebay.
http://www.realsteel.co.uk
Edited by barkychoc on Thursday 7th October 19:05
Go for the alloy sandwich type gaskets from most good tvr suppliers - V8 developments, act etc. The arp stainless bolts are a must, much easier getting them on/off in the future. You will need to clean the faces on the head and manifold and at the y piece if you are splitting it.
For me putting the car on ramps is a must; removing the exhaust and removing the starter motor helps get to the rear bolts on both sides.
I needed to grind some spanners to get the bolts on or off and used a number of different spanners -swan necks etc. For a first timer it is a pita but certainley doable. PM if you need any help and good luck
For me putting the car on ramps is a must; removing the exhaust and removing the starter motor helps get to the rear bolts on both sides.
I needed to grind some spanners to get the bolts on or off and used a number of different spanners -swan necks etc. For a first timer it is a pita but certainley doable. PM if you need any help and good luck
Thanks all for the advice.
Update: I managed to get 7 of the 8 bolts free with relative ease the hardest one was the bottom front near the alternator. But with that removed it was pretty easy.
now comes the hard part the bottom rear. I will have to take off the starter motor (which is not a bad thing I have been meaning to clean up the connectors for a while and give it an inspection) then it should be relatively easy.
One thing I did think of whilst under the car a 14mm spanner that is about 18 inches long would be really handy. And if I need to do the passenger side thats just what I will get/manufacture because having had a look, all four bolts would be accessible with just such a beast.
I will keep you updated, if you are interested. (well I'll do it even if you're not interested to be honest)
Kwacker
Ps. the hardest thing so far has been moving all the stuff, the bikes, the car, jacking up the car, and putting it all away again!
Update: I managed to get 7 of the 8 bolts free with relative ease the hardest one was the bottom front near the alternator. But with that removed it was pretty easy.
now comes the hard part the bottom rear. I will have to take off the starter motor (which is not a bad thing I have been meaning to clean up the connectors for a while and give it an inspection) then it should be relatively easy.
One thing I did think of whilst under the car a 14mm spanner that is about 18 inches long would be really handy. And if I need to do the passenger side thats just what I will get/manufacture because having had a look, all four bolts would be accessible with just such a beast.
I will keep you updated, if you are interested. (well I'll do it even if you're not interested to be honest)
Kwacker
Ps. the hardest thing so far has been moving all the stuff, the bikes, the car, jacking up the car, and putting it all away again!
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



t of a job