Discussion
I've been changing the veneer on the dash for something a bit more modern and in doing so I noticed when I disconnected the rev counter at the rear there is a light which is not connected. It looks like it illuminates a red rectangular light on the rev counter however the cable is attached to the bulb but the other end is just tied up and not connected. Is this a rev limiter/warning light and if so was it optional (which maybe why it's not connected) or was it connected as standard and has been disconnected by a previous owner? If it is meant to be connected how do I find the connectors? Cheers for any info.
Hi fogg66, I seem to remember in a previous post that it was an optional gear change indicator light? How did you get on with re-veneering your dash? I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost? Cheers John042
It's a gear change warning lamp, not used in the Chimaera, but the same rev counter is used in the Cerbera, where the lamp is connected.
I used it as a warning lamp for the fan override.
I used it as a warning lamp for the fan override.
John042 said:
...I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost?...
I had mine re-veneered a few years ago by a mandolin maker. I think it cost around £250 for both panels and, as he hadn't applied a veneer to mild steel before, it took a bit of trial and error with different adhesives. The finished product was fantastic and included around 25 coats of lacquer. Unfortunately the car spent the subsequent winter months with the roof panel not properly fitted and the resultant damp caused it to start peeling again.At the moment I'm making two new sets of panels. One will be the original steel panels in carbon fibre; the other will be burr walnut veneer again, but on a 2mm MDF backing. Going much thicker than that would cause problems refitting it: the support brackets would need modifying, the main panel would need a curve in it and the radio panel would be difficult to fit properly, it being surface mounted.
The firm that springs to mind that will re-veneer the panels is London Carriage Craft. Over the years I've read of quite a few owners on here that have been happy with their work.
John042 said:
Hi fogg66, I seem to remember in a previous post that it was an optional gear change indicator light? How did you get on with re-veneering your dash? I've got a chap whose willing to have a 'crack' at it, either replacing the veneer or even making a complete wooden one. Which would, I guess, negate the chance of future cracking. Are there firms who will re-veneer your dash and what's the likely cost? Cheers John042
I didn't re veneer, I'm using a carbon effect wrap. Looks good so far, I've completed and installed the radio panel and I'll be finishing the main dash at the weekend. Fingers crossed scratch free!Looks like the light doesn't need to be connected, cheers.
Very impressive fog66. Against red, but, I wonder with pale tan? Does it come in different shades and from which supplier. The curved main panel fills me with concern not only with size but being 'in your face' all the time. Was it easy to apply,trim and did you use a compact glue? Thanks John042
John042 said:
Very impressive fog66. Against red, but, I wonder with pale tan? Does it come in different shades and from which supplier. The curved main panel fills me with concern not only with size but being 'in your face' all the time. Was it easy to apply,trim and did you use a compact glue? Thanks John042
This wrap stuff is self adhesive, a but like old school fablon. As long as you take your time it's really quite easy. Your interior sounds like biscuit? I think the stuff I've used only comes in black or White from the supplier I'm using (he's local to me in Newcastle upon Tyne) his business is vinyl signing. I got the two bits I've used FOC as they were off cuts but it costs £52 per metre. Why not post a picture of your current interior and we can assess how it might look, all on our own opinion if course. Phil. Thanks fog66 (Phil) very impressive against a darker surround. Unfortunately my beast is in dis-array steering wheel of bits of trim etc so a pic might not be much use. The leather trim is cream (Magnolia?) a dark covered dash might not be the answer. Veneering might be the only course of action? Thanks again for the info and pics. Cheers John042.
Gassing Station | Chimaera | Top of Page | What's New | My Stuff






