Temp gauge and cooling fans issue...
Discussion
Morning, any ideas on this...my temp gauge has always been consistant (who knows if accurate or not), I know that wby the time I get to work the temp is around the 90 mark. The Fans will vut in and out for 15 secs at a time.
The last few days on the same journey in the same traffic, the temp gause has only been getting upto 70 (at a struggle) yet the fans have been kicking in at the 60-70 mark, and then running often for longer than they do when the car used to get upto 90+
This is much different to the past 7 years worth of behaviour.
Any thoughts on why they may have suddently started...would a dodgy temp sensor cause this sort of thing.
Cheers
James
The last few days on the same journey in the same traffic, the temp gause has only been getting upto 70 (at a struggle) yet the fans have been kicking in at the 60-70 mark, and then running often for longer than they do when the car used to get upto 90+
This is much different to the past 7 years worth of behaviour.
Any thoughts on why they may have suddently started...would a dodgy temp sensor cause this sort of thing.
Cheers
James

You're right to ignore the accuracy of the readings and to concentrate on the change in behaviour. Unfortunately the cause may be difficult to diagnose correctly.
The fans are controlled by the otter switch. AFAIK, when it fails it tends to either leaves the fans permanently or or permanently off. So let's assume for the moment it's working correctly.
The temperature gauge approximates the coolant temperature near the thermostat. If it's working correctly it should reach a peak just before the thermostat opens. This should coincide with the fans operating, assuming the coolant temperature is within the operating range of the otter switch.
The most logical solution I can come up with is the thermostat has failed, probably by sticking open. That would explain why the temperature gauge isn't reaching its normal peak. And if it's allowing a more continuous flow of coolant rather than a stop/start flow (and the coolant temperature's in the otter switch range), the fans would probably run for longer periods.
Next time you start the car from cold, leave it to idle and feel the top hose (from thermostat to swirl pot). It should warm slightly as the engine warms up and coolant flows through the bypass drilling in the thermostat. When normal coolant temperature is reached it should suddenly become very hot. If the thermostat's stuck open it will warm up steadily.
The fans are controlled by the otter switch. AFAIK, when it fails it tends to either leaves the fans permanently or or permanently off. So let's assume for the moment it's working correctly.
The temperature gauge approximates the coolant temperature near the thermostat. If it's working correctly it should reach a peak just before the thermostat opens. This should coincide with the fans operating, assuming the coolant temperature is within the operating range of the otter switch.
The most logical solution I can come up with is the thermostat has failed, probably by sticking open. That would explain why the temperature gauge isn't reaching its normal peak. And if it's allowing a more continuous flow of coolant rather than a stop/start flow (and the coolant temperature's in the otter switch range), the fans would probably run for longer periods.
Next time you start the car from cold, leave it to idle and feel the top hose (from thermostat to swirl pot). It should warm slightly as the engine warms up and coolant flows through the bypass drilling in the thermostat. When normal coolant temperature is reached it should suddenly become very hot. If the thermostat's stuck open it will warm up steadily.
I had something similar, only the other way. The car now reads at a good 95 degrees when normal then somewhere at 100 when the fans kick in, where as before it was lower.
Turns out the sensor had failed/malfunctioned. I checked the cooling temps with a thermal probe and replaced all the eaisly fixable parts (otter switch, thermostat, rad) then checked for leaks and bled it like there was no tomorrow. Car runs fine, gauge is just out.
I have a new sensopr to fit once I have some time.
Check the temp with a digital thermometer.
Turns out the sensor had failed/malfunctioned. I checked the cooling temps with a thermal probe and replaced all the eaisly fixable parts (otter switch, thermostat, rad) then checked for leaks and bled it like there was no tomorrow. Car runs fine, gauge is just out.
I have a new sensopr to fit once I have some time.
Check the temp with a digital thermometer.
spend said:
Take it very seriously... You may have air in the coolant system! this can be early warning of a leak.
I agree... air.. taking the sensor for the gauge out of the coolant so cant read it (hence the cool indication).. but water reaching temp if not hotter than before... Could be a leak for sure......Are you loosing coolant / getting bubbles in the header tank at all??.. Try run it with the cap off and see what happens?
Gassing Station | Chimaera | Top of Page | What's New | My Stuff


